window ISUZU TFS SERIES 1997 Owner's Manual

10-8 CAB
SLIDING REAR WINDOW ASSEMBLY
DISASSEMBLY
Disassembly Steps
1. Weather strip
2. Packing ; rear window
3. Screw; binding
4. Frame ; rear window
5. Stopper
6. Rear window ; slide
7. Lock assembly with catchback window
8. Glass run
9. Glass ; rear window corner
10. Weather strip ; rear window corner

CAB 10-9
Important Operation - Removal
1. Weather Strip
Remove the weather strip with a knife.
2. Packing ; Rear Window
With a screwdriver or similar tool, remove the window stop.
4. Frame ; Rear Window
Place the window channel in a vertical position and remove the
frame rear by pulling on one end of it with your hand.
6. Rear Window ; Slide
With the window channel held in a vertical position, remove the
rear window ; slide.
9. Glass ; Rear Window Corner
Stand the window channel up and remove the glass ; rear
window corner.

10-10 CAB
REASSEMBLY
Riassembly Steps
1. Weather strip ; rear window corner
2. Glass ; rear window corner
3. Glass run
4. Frame ; rear window
5. Screw; binding
6. Rear window ; slide
7. Stopper
8. Packing ; rear window
9. Lock assembly with catchback window
10. Weather strip

CAB 10-11
Important Operation - Installation
1. Weather Strip ; Rear Window Corner
Using Semedain #560 (or equivalent) adhesive, glue the
weather strip to the complete circumference of the frame,
paying close attention to the corner areas.
2. Glass ; Rear Window Corner
Apply soap and water to the rim as a lubricant.
Place the channel in a vertical position. With your hand, apply
pressure to expand the channel. Insert the window glass in the
center of the channel.
3. Glass Run
Apply Semedain #560 (or equivalent) adhesive to the entire
length of both the upper window glass and the weather strip.
Apply adhesive to both sides of the extreme ends of the lower
portion for a distance of about 50 mm.
There should be no gap between the weather strip rear window
glass channel and the channel.
6. Rear Window ; Slide
Hold the window vertically. Apply an upward pressure to the
channel and insert the rear window slide.
8. Packing ; Rear Window
Apply a fast setting adhesive agent to both sides of the window
atop and insert it into the channel.

CAB 10-15
DISASSEMBLY
(Front Door)
87 910
11 6
Disassembly Steps
1. Power window switch/Windows regulator
handle
2. Bezel
3. Speaker grill
4. Speaker assembly
5. Door pull case
6. Door mirror cover/Tweeter
7. Door trim pad
8. Door pocket
9. Power window box
10. Inner waste seal
11. Outer waste seal
12. Door mirror assembly
13. Door mirror bracket
14. Bracket
15. Speaker box
16. Water-proof sheet
17. Window glass
18. Window regulator/Power window motor
19. Glass run
20. Glass run rear channel
21. Inside lever
22. Door lock assembly/Door lock actuator
23. Glass run front channel
24. Door lock cylinder
25. Outside handle

10-16 CAB
Important Operations
1. Power Window Switch/Window Regulator Handle
Prise out the power window switch and remove the
connectors.
To remove the regulator handle, remove the clip at the
root of the handle by using wire.
2. Bezel
Remove the screw while pulling the inside lever toward
you.
3. Speaker Grill
Pull out the clips.
4. Speaker Assembly
Remove 4 screws and disconnect the speaker harness
connector.
5. Door Pull Case
Remove the screw at the bottom of the case.

CAB 10-17
6. Door Mirror Cover/Tweeter
Pull out the upper clip, and then take out the catch at the
lower section.
If so equipped the tweeter, disconnect the speaker
harness connector.
7. Door Trim Pad
Remove the cover bottom of the trim pad (4 pcs), then
remove the screws.
8. Door Pocket
9. Power Window Box
10.Inner Waste Seal
11.Outer Waste Seal
12.Door Mirror Assembly
Remove 3 fixing bolts and then remove the connector.
13.Door Mirror Bracket
Remove 2 bolts at the lower section, and then remove 2
screws in the weather strip.
14.Bracket
15.Speaker Box
Remove 3 fixing bolts.
16.Water Proof Sheet
Take care not to damage the sheet when peeling it off.

10-18 CAB
17.Window Glass
Remove 2 screws through the access hole and pull out
the window glass upward.
18.Window Regulator/Power Window Motor
Disconnect the power window motor connector.
19.Glass Run
Pull it out of the door piller of the channel. (front/rear)
20.Glass Run Rear Channel
Remove 2 screws.
21.Inside Lever
22.Door Lock Assembly/Door Lock Actuator
Disconnect the linkage with the outside handle, the
inside lever and the lock cylinder.
23.Glass Run Front Channel
24.Door Lock Cylinder
Remove the door lock cylinder by applying finger
pressure from inside while depressing the retaining clip.
25.Outside Handle

CAB 10-19
DISASSEMBLY AND REASSEMBLY
(Rear Door)
3
2
910 181219 13
1716
15 14
6
5 4 1611
7
68
Disassembly Steps
1.Power window switch/Window regurator
handle
2. Speaker grill
3. Speaker
4. Bezel
5. Inside pull handole
6. Door trim pad
7. Arm rest sm
8. Bracket
9. Water proof sheet
10. Glass guide
11. Upper cover
12. Window regurator/Power window motor
13. Window glass
14. Bracket15. Inside lever
16. Outside handle
17. Door lock cylinder
18. Outer waste seal
19. Glass run
Reassembly Steps
To reassemble, follow the disassembly steps
in the reverse order.

10-20 CAB
Important Operations
1. Window Regulator Handle
To remove the regulator handle, remove the clip at the
root of the handle by using wire.
4. Bezel
Remove the screw while pulling the inside lever toward
you.
6. Door Trim Pad
Remove the cover bottom of the trim pad (4 pcs), then
remove the screws.
12.Window Regulator
Remove the 4 screws holding the regulator.