4WD ISUZU TROOPER 1998 Service Owner's Manual

DRIVE LINE CONTROL SYSTEM (TOD) 4B2±24
No.NAMECONTENTS
1VIGPower supply (IG)
2N.CNot used
34WD OUT4WD signal output
4SOL (+)Electromagnetic solenoid
5ADC (+)Axle disconnect output
6LIGHTING SWLighting SW input
7BRAKEBrake SW input
84H SW4H SW input
94L SW4L SW input
10AXEL SWAXEL SW input
11ABS INOperation signal input
12TOD SWTOD SW input
13DIAGSelf-diagnosis input
14D-G MAPD-G MAP recognition input (Only V6 engine)
15Ref.Vehicle speed sensor supply
16N.CNot used
17US/JAPDestination recognition input
18COM (±)Vehicle speed sensor GND
19S-GNDSensor GND
20P-GNDPower GND
21TPSThrottle position sensor
22TECH 2TECH 2 output
23Rer. SigRear vehicle speed sensor input
24Frt. SigFront vehicle speed sensor input
25IND.a4WD disply signal a
26IND.b4WD display signal b
27IND.c4WD display signal c
28IND.AUTOAUTO display output
29IND RrRear display output
30CHECKTOD warning lamp

DRIVE LINE CONTROL SYSTEM (TOD) 4B2±26
Checking Failed TOD Control Unit Pin
NOTE:
1. Unplug the ECU connector and the pins, unless
otherwise specified.2. Before removing the ECU, turn off the ignition switch.
3. If the standard values are not observed, check the
pins with other testers.
Check
Pin
No.Circuit to be
testedIgnition
Switch
PositionEngine
StateMultimeter
Scale/
RangeMeasure
between Pin
NumberStandard ValveNote
14D-G MAPOFFSTOP
14, 19Continuity : OK
(Gasoline)
20P-GNDOFFSTOP
20, 19Continuity : OK
19GNDOFFSTOP
19, GNDContinuity : OK
84H SWOFFSTOP
8, 19No continuity (high,
4L) and continuity
(N) : OK
94L SWOFFSTOP
9, 19No continuity (high)
and continuity (4L,
N) : OK
10AXLE SWONRUN
10, 19Continuity : OKRemove ECU and start the engine. Move
the vehicle forth and back to connect axle
surely.
13DIAGOFFSTOP
13 (TOD), 8
(DLC Con-
nector)Continuity : OKDLC connector terminal 8
25IND.aONSTOPDCV25 (+), 19 (±)8.0 ~14.5 VLighting SW ON : 0V
Lighting SW OFF : 8.0 ~14.5 V
26IND.bONSTOPDCV26 (+), 19 (±)8.0 ~14.5 V
27IND.cONSTOPDCV27 (+), 19 (±)8.0 ~14.5 V
30CHECK
LAMPONSTOPDCV30 (+), 19 (±)8.0 ~14.5 V
11ABS INONSTOPDCV11 (+), 19 (±)11.5 ~14.5 V
15Ref.ONSTOPDCV15 (+), 19 (±)5 ~9 VConnect ECU
24Ft.(+)ONSTOPDCV24 (+), 19 (±)0.7 ~6 VConnect ECU (off one tooth of speed
sensor ring) and move the vehicle making
sure of voltage change.
23Rr.(+)ONSTOPDCV23 (+), 19 (±)0.7 ~6 VConnect ECU (off one tooth of speed
sensor ring) and move the vehicle making
sure of voltage change.
18COM(-)ONSTOPDCV18 (+), 19 (±)0VConnect ECU
1VigONSTOPDCV1 (+), 19 (±)8 ~14.5 V
7BRAKEOFFSTOPDCV7 (+), 19 (±)8 ~14.5 VPress brake pedal
21TPSONSTOPDCV21 (+), 19 (±)0.2 ~4.6 VStep on the accelerator pedal and make
sure that voltage changes.
34WD OUTOFFSTOP
3, 197 ~12 k
Disconnect battery GND terminal
5ADC(+)OFFSTOP
5, 1910 ~30
Disconnect battery GND terminal
4SOL(+)OFFSTOP
4, 191.0 ~5.0
Disconnect battery GND terminal
12TOD SWONSTOPDCV12 (+), 19 (±)SW OFF : 0 V
SW ON : 8.0 ~14.5 VSW OFF : Contact point open
SW ON : Contact point close
6LIGHTINGONSTOPDCV6 (+), 19 (±)SW OFF : 8.0 ~14.5
V
SW ON : 0 V
28AUTO INDIONSTOPDCV28 (+), 19 (±)TOD : 0 V
2H & 4L : 8.0 ~14.5
VLighting SW ON : 0V
Lighting SW OFF : 8.0 ~14.5 V
29RR INDIONSTOPDCV29 (+), 19 (±)0 V
17US/JAPOFFSTOP
17 (+), 19 (±)No continuity : OK

DRIVE LINE CONTROL SYSTEM (TOD) 4B2±50
Check flowTrouble codePhenomenonStandard
1128The shift on the fly system (front
hub) works incorrectly.Ð
NOTE: T h e s h i f t o n t h e f l y s y s t e m i s n o t changed
between 2WD and 4WD modes normally.CAUTION: If code 32 or 33 is also observed, remove
the trouble associated with code 32 or 33 first.
D04RW058

4B2±61 DRIVE LINE CONTROL SYSTEM (TOD)
Chart B±1The 4WD switch circuit wires are broken or short-circuited to the GND
Function of circuitÐ
Fail conditionEven after the transfer mode is selected from TOD to 2H, the indicator lamp status is not
changed.
Indicator lamp status
Ð
Transfer position2HÐ
D04RW062

DRIVE LINE CONTROL SYSTEM (TOD) 4B2±62
StepActionYe sNo
11. Turn on the starter switch.
When the 4WD SW is selected to the 4WD position, is 0 V
observed between terminal 12 and 19?
Go to Step 2
Repair the 4WD
SW circuit.
Go to Step 4
2When the 4WD SW is selected to the 2WD position, is 12 V
observed between terminals 12 and 19?
Go to Step 3
Repair the 4WD
SW circuit.
Go to Step 4
3When the transfer lever is shifted to the 4L position, is battery
boltage observed between terminals 28 and 19?The phenomenon
is not
reproduced.
Refer to
ªTroubles
intermittently
observedº.
Go to Step 4
Replace the
ECU.
Go to Step 4
4Check that all the parts are mounted.
Is this step complete?Repeat the
ªDiagnosis Flowº.
Return to Step 4

4B2±63 DRIVE LINE CONTROL SYSTEM (TOD)
Chart B±2The 4WD switch circuit is short to battery.
Function of circuitÐ
Fail conditionEven after the transfer mode is selected from 2H to TOD, the indicator lamp status dose
not change.
Indicator lamp status
Transfer positionTOD
D04RW062

DRIVE LINE CONTROL SYSTEM (TOD) 4B2±64
StepActionYe sNo
1When the 4WD SW is selected to the 4WD position, is 0 V
observed between terminal 12 and 19?
Go to Step 2
Repair the 4WD
SW circuit.
Go to Step 7
2When the 4WD SW is selected to the 2WD position, is 12 V
observed between terminals 12 and 19?
Go to Step 3
Repair the 4WD
SW circuit.
Go to Step 7
31. Disconnect the ECU connector.
Is the continuity established between terminals (B±67)1 and
(B±68)13?
Go to Step 4
Replace TOD
indicator lamp
bulb.
Go to Step 7
4Is the continuity established between terminals (B±67)1 and
(B±68)14?
Go to Step 5
Replace TOD
indicator lamp
bulb.
Go to Step 7
5Is the continuity established between terminals (B±67)1 and
(B±68)15?
Go to Step 6
Replace TOD
indicator lamp
bulb.
Go to Step 7
6Is the continuity established between terminals (B±67)1 and
(B±68)16?
Replace ECU.
Go to Step 7
Replace TOD
indicator lamp
bulb.
Go to Step 7
7Check that all the parts are mounted.
Is this step complete?Repeat the
ªDiagnosis Flowº.
Return to Step 7

4B2±65 DRIVE LINE CONTROL SYSTEM (TOD)
Chart C±14H switch circuit wires are broken or the battery is short-circuited.
Function of circuitÐ
Fail conditionWhen the 4WD SW is 4WD mode.
When the lever is shifted from 4L to HIGH, the 4L mode remains on the indicator and the
TOD mode is displayed without turning off the previous mode.
Indicator lamp status
Transfer position4L <ÐÐ> Neutral <ÐÐ> TOD
D04RW062

DRIVE LINE CONTROL SYSTEM (TOD) 4B2±74
StepActionYe sNo
1When the transfer lever is shifted to the high position, is 5V
observed between terminals 9 and 19 (4L switch)?
Go to Step 2Go to Step 7
2When the transfer lever is shifted to the neutral position, is 0V
observed between terminals 9 and 19 (4L switch)?
Go to Step 3Go to Step 7
3When the transfer lever is shifted to the 4L position, is 0V
observed between terminals 9 and 19 (4L switch)?
Go to Step 4Go to Step 7
41. Shift the 4WD SW to the 2H position.
Is 12V observed between terminals 25 and 19?
Go to Step 5
The ECU has
failed. Replace
the ECU.
Go to Step 16
5Is 12V observed between terminals 26 and 19?
Go to Step 6
The ECU has
failed. Replace
the ECU.
Go to Step 16
6Is 12V observed between terminals 27 and 19?The phenomenon
is not
reproduced.
Refer to
ªTroubles
intermittently
observedº.
Go to Step 16
The ECU has
failed. Replace
the ECU.
Go to Step 16
71. Turn off the starter switch.
2. Disconnect the ECU connector.
When the transfer lever is shifted to the neutral position between
High and 4L, is the continuity established between terminals
(B±68)4 and (B±67)11?
Go to Step 8Go to Step 10
8When the transfer lever is shifted to the 4L position, is the
continuity established between terminals (B±68)4 and (B±67)11?
Go to Step 9Go to Step 10
9When the transfer lever is shifted to the high position, is the
continuity established between terminals (B±68)4 and (B±67)11?
Go to Step 10
The ECU has
failed. Replace
the ECU.
Go to Step 16
101. Disconnect the H-49 connector.
When the transfer lever is shifted to the neutral position between
high and 4L, is the continuity established between terminals
(H-49)5 and (B-67)11?
Go to Step 11Go to Step 13
11When the transfer lever is shifted to the 4L position, is the
continuity established between transfer connector terminals
(H-49)5 and (B-67)11?
Go to Step 12Go to Step 13
12When the transfer lever is shifted to the high position, is the
continuity established between terminals (H-49)5 and (B-67)11?
Go to Step 13
GND is
short-circuited
between
terminals (B±68)4
and (H-49)5.
Repair the circuit.
Go to Step 16
131. Disconnect the A-3 connector.
When the transfer lever is shifted to the neutral position between
high and 4L, is the continuity established between terminals
(A-3)12 and GND?
Go to Step 14
Repair the
transfer
assembly.
Go to Step 16

4B2±77 DRIVE LINE CONTROL SYSTEM (TOD)
StepActionYe sNo
1Start the engine.
When the transfer lever is shifted to the neutral position between
high and 4L, is 5V observed between terminals 10 and 19?
Go to Step 2Go to Step 7
2When the transfer lever is shifted to the high position and 4WD
switch shifted to 4WD position, is 0V observed between terminals
10 and 19?
Go to Step 3Go to Step 7
3When the transfer lever is shifted to the 4L position, is 0V
observed between terminals 10 and 19?The ECU has
failed. Replace
the ECU.
Go to Step 4
Go to Step 7
4Shift the transfer lever to the 4L position.
Is 0V observed between terminals 25 and 19?
Go to Step 5
The ECU has
failed. Replace
the ECU.
Go to Step 19
5Is 0V observed between terminals 26 and 19?
Go to Step 6
The ECU has
failed. Replace
the ECU.
Go to Step 19
6Is 0V observed between terminals 27 and 19?The phenomenon
is not
reproduced.
Refer to
ªTroubles
intermittently
observedº.
Go to Step 19
The ECU has
failed. Replace
the ECU.
Go to Step 19
7When the transfer lever is shifted to the 2H position, is the battery
voltage observed between terminals 5 and 19?
Go to Step 8Go to Step 11
8When the transfer lever is shifted to the neutral position between
high and 4L, is the battery voltage observed between terminals 5
and 19?
Go to Step 9Go to Step 11
9When the transfer lever is shifted to the high position (TOD mode),
is 0V observed between terminals 5 and 19?
Go to Step 10Go to Step 11
10When the transfer lever is shifted to the 4L position, is 0V
observed between terminals 5 and 19?
Go to Step 12Go to Step 11
11Is any of the trouble codes 28, 32 and 33 recorded?Examine the
trouble based on
ªDiagnosis from
Trouble Codesº.
Go to Step 19
The ECU has
failed. Replace
the ECU.
Go to Step 19
121. Turn off the starter switch.
2. Disconnect the ECU connector.
Does the resistance between terminals (B±67)5 and (B±67)11
meet the standard, 17< R < 25 ohm?
Go to Step 13
Repair the circuit
or replace the
VSV.
Go to Step 16
131. Turn on the starter switch.
When the 4WD SW is selected to the 2WD position, is the battery
voltage supplied to each VSV?
Go to Step 14
Repair the circuit
or replace the
VSV.
Go to Step 16
14When the transfer lever is shifted to the neutral position between
high and 4L, is the battery voltage supplied to each VSV?
Go to Step 15
Repair the circuit
or replace the
VSV.
Go to Step 19