coolant temperature ISUZU TROOPER 1998 Service Owner's Manual

6A±21
ENGINE MECHANICAL
Cylinder Head Cover RH
Removal
1. Disconnect battery ground cable.
2. Remove battery from the vehicle.
3. Drain engine coolant from faucet bottom of radiator.
4. Remove engine cover from the dowels on the
common chamber.
F06RW018
5. Remove air cleaner duct assembly (3) and air cleaner
element (4).
130RW001
Legend
(1) Positive Crankcase Ventilation Hose Connector
(2) Intake Air Temperature Sensor
(3) Air Cleaner Duct Assembly
(4) Air Cleaner Element
(5) Mass Air Flow Sensor
NOTE: Disconnect the mass air flow (MAF) sensor
connector, intake air temperature (IAT) sensor connector,
and positive crankcase ventilation (PCV) hose before
hand the air cleaner duct assembly is removed.
6. Disconnect following wiring connectors and bonding
cable:

Exhaust Gas Recirculation (EGR) valve

Fuel injectors for right bank

Ignition coils for right bank

Bonding cable

Othres as necessitated
7. Disconnect radiator upper and lower hoses.
8. Remove engine harness from the cylinder head
cover.
9. Remove the upper fan guide.
10. Remove cooling fan and clutch assembly.
11. Remove drive belt by pushing down the auto
tensioner using spanner as illustrated.
F06RW019
Legend
(1) Crankshaft Pulley
(2) Generator
(3) Auto Tensioner
(4) Idle Pulley
(5) Cooling Fan Pulley
(6) Power Steering Oil Pump
(7) Drive Belt
(8) Air Conditioner Compressor
12. Remove fan pulley and bracket assembly.
13. Remove idle pulley assembly.
14. Remove auto tensioner assembly.
15. Remove crankshaft pulley using 5±8840±0133±0
crankshaft holder.

ENGINE COOLING6B±3
Thermostat
The thermostat is a wax pellet type with a air hole(1) and is
installed in the thermostat housing.
031RW002
Radiator
The radiator is a tube type with corrugated fins. In order to
raise the boiling point of the coolant, the radiator is fitted
with a cap in which the valve is operated at 88.2 ~ 117.6
kPa (12.8 ~ 17.0 psi) pressure. (No oil cooler provided for
M/T)
110RS001
Anti Freeze Solution

Relation between the mixing ratio and freezing
temperature of the EC varies with the ratio of
anti±freeze solution in water. Proper mixing ratio can
be determined by referring to the chart. Supplemental
inhibitors or additives claiming to increase cooling
capability that have not been specifically approved by
Isuzu are not recommended for addition to the cooling
system.

Calculating mixing ratio
F06RW005

6B±4
ENGINE COOLING
NOTE: An t if r e e ze s o lu t io n + Water = Total cooling
system capacity.

Total Cooling System Capacity

M/T 8.8Lit (2.32Us gal)

A/T 8.4Lit (2.22Us gal)
B06RW002

Mixing ratio
Check the specific gravity of engine coolant in the
cooling system temperature ranges from 0
C to 50
C
using a suction type hydrometer, then determine the
density of the engine coolant by referring to the table.
NOTE:
1. Even in the areas where the atmospheric
temperature is higher than 0
C, be sure not to use
antifreeze solution at a mixing ratio lower than 20% so
that the inside of the engine may not be corroded.
2. If antifreeze solution is used at a mixing ratio higher
than 60%, the specific heat of the coolant falls and the
engine may be overheated. Moreover, antifreeze
performance drop and the coolant may be frozen.
The density of the solution must be adjusted as
occasion calls.
Antifreeze solution lower than 20% may not have
sufficient anticorrosive performance, and therefore,
please never fail to adjust as occasion demands within
the range of 20% to 60%.
B06RW003

ENGINE COOLING6B±5
Diagnosis
Engine Cooling Trouble
ConditionPossible causeCorrection
Engine overheatingLow Engine Coolant levelReplenish
Incorrect fan installedReplace
Thermo meter unit faultyReplace
Faulty thermostatReplace
Faulty Engine Coolant temperature
sensorRepair or replace
Clogged radiatorClean or replace
Faulty radiator capReplace
Low engine oil level or use of
improper engine oilReplenish or change oil
Clogged exhaust systemClean exhaust system or replace
faulty parts
Faulty Throttle Position sensorReplace throttle valve assembly
Open or shorted Throttle Position
sensor circuitRepair or replace
Damaged cylinder head gasketReplace
Engine overcoolingFaulty thermostatReplace
Engine slow to warm±upFaulty thermostatReplace
Thermo unit faultyReplace

6B±8
ENGINE COOLING
3. Idle pulley

Install idle pulley and tighten bolt to the specified
torque.
Torque: 52 N´m (5.3 Kg´m/38 lb ft)4. Timing belt

Install timing belt. Refer to timing belt installation
step in ªTiming Beltº in this manual.
5. Connect radiator inlet hose and replenish EC.
6. Connect battery ground cable.
Thermostat
Thermostat and Associated Parts
031RW001
Legend
(1) Thermostat Housing
(2) Thermostat
(3) Outlet Pipe
Removal
1. Disconnect battery ground cable.
2. Drain engine coolant from the radiator and engine.
3. Disconnect radiator hose from the inlet pipe.
4. Remove thermostat housing.
5. Remove thermostat(2).
Inspection
Suspend the thermostat in a water±filled container using
thin wire. Place a thermometer next to the thermostat.
Do not directly heat the thermostat.
Gradually increase the water temperature. Stir the water
so that the entire water is same temperature.
031RS003Confirm the temperature when the valve first begins to
open.
Valve opening temperature 74.5C ~ 78.5
C
(166.1
F ~ 173.3
F)
Confirm the temperature when the valve is fully opened.
Valve full open temperature and lift More than
8.5mm (0.33 in) at 90
C (194
F)
Make necessary repair and parts replacement if extreme
wear or damage is found during inspection.
Installation
1. Install thermostat into the outlet pipe(4) making sure
that the air hole is in the up position.
2. Install thermostat housing and tighten bolts to the
specified torque.
Torque: 25 N´m (2.5 Kg´m/18 lb ft)
3. Installation rubber hose.
4. Replenish engine coolant (EC).
5. Start engine and check for EC leakage.

ENGINE COOLING6B±11
Cap tester: 5±8840±0277±0
Adapter: 5±8840±2603±0
110RS005
Installation
1. Install rubber cushions on both sides of radiator
bottom.
2. Install radiator assembly with hose, taking care not to
damage the radiator core with a fan blade.
3. Install bracket (6) and support the radiator upper tank
with the bracket (5) and secure the radiator.
4. Connect reserve tank hose (4).
5. Install lower fan guide (3).
6. Connect radiator inlet hose and outlet hose to the
engine.
7. Connect oil cooler hose (1) to automatic
transmission.
110RW004
8. Connect battery ground cable.
9. Pour engine coolant up to filler neck of radiator, and
up to MAX mark of reserve tank.
111RS001Important operation (in case of 100% engine coolant
change) procedure for filling with engine coolant.
1. Make sure that the engine is cool.
2. Open radiator cap pour coolant up to filler neck.
3. Pour coolant into reservoir tank up to ªMAXº line.
4. Tighten radiator cap and start the engine. After
idling for 2 to 3 minutes, stop the engine and
reopen radiator cap. If the water level is lower,
replenish.
WARNING: WHEN THE COOLANT IS HEATED TO A
HIGH TEMPERATURE, BE SURE NOT TO LOOSEN
OR REMOVE THE RADIATOR CAP. OTHERWISE YOU
MIGHT GET SCALDED BY HOT VAPOR OR BOILING
WATER. TO OPEN THE RADIATOR CAP, PUT A
PIECE OF THICK CLOTH ON THE CAP AND LOOSEN
THE CAP SLOWLY TO REDUCE THE PRESSURE
WHEN THE COOLANT HAS BECOME COOLER.
5. After tightening radiator cap, warm up the engine
at about 2000 rpm. Set heater adjustment to the
highest temperature position, and let the coolant
circulate also into heater water system.
6. Check to see the thermostat has opened through
the needle position of water thermometer,
conduct a 5±minute idling again and stop the
engine.
7. When the engine has been cooled, check filler
neck for water level and replenish if required.
Should extreme shortage of coolant is found,
check the cooling system and reservoir tank hose
for leakage.
8. Pour coolant into reservoir tank up tp ªMAXº line.

ENGINE COOLING6B±13
Main Data and Specifications
General Specifications
M/TA/T
Cooling systemEngine coolant forced circulation
Radiator(1 tube in row) Tube type corrugated (2 tube in row)
Heat radiation capacity68,000 kcal/h77,000 kcal/h
Heat radiation area9.445m
(0.878ft
)11.21m
(1.04ft
)
Radiator front area0.302m
(0.028ft
)
Radiator dry weight39N (8.8lb)44N (9.9lb)
Radiator cap valve opening pressure93.3 ~ 122.7kpa (13.5 ~ 17.8psi)
Engine coolant capacity2.5lit (2.6U.S q.t.)2.4lit (2.5U.S q.t.)
Engine coolant pumpCentrifugal impeller type
Delivery300 (317) or more
Pump speed5000 + 50 rpm
ThermostatWax pellet type with air hole
Valve opening temperature74.5 ~ 78.5
C (166.1 ~ 173.3
F)
Engine coolant total capacity10.4lit (11.0U.S qt)10.5lit (11.1U.S qt)
Torque Specifications
N´m (Kg´m/lb ft)

E06RW041

6E±3 ENGINE DRIVEABILITY AND EMISSIONS
Diagnostic Trouble Code (DTC) P0351
Ignition 1 Control Circuit 6E±206. . . . . . . . . . . . . . . . .
Diagnostic Trouble Code (DTC) P0352
Ignition 2 Control Circuit 6E±209. . . . . . . . . . . . . . . . .
Diagnostic Trouble Code (DTC) P0353
Ignition 3 Control Circuit 6E±212. . . . . . . . . . . . . . . . .
Diagnostic Trouble Code (DTC) P0354
Ignition 4 Control Circuit 6E±215. . . . . . . . . . . . . . . . .
Diagnostic Trouble Code (DTC) P0355
Ignition 5 Control Circuit 6E±218. . . . . . . . . . . . . . . . .
Diagnostic Trouble Code (DTC) P0356
Ignition 6 Control Circuit 6E±221. . . . . . . . . . . . . . . . .
Diagnostic Trouble Code (DTC) P0402
EGR Pintle Crank Error 6E±224. . . . . . . . . . . . . . . . . .
Diagnostic Trouble Code (DTC) P0404
EGR Open Stuck 6E±226. . . . . . . . . . . . . . . . . . . . . . .
Diagnostic Trouble Code (DTC) P0405
EGR Low Voltage 6E±228. . . . . . . . . . . . . . . . . . . . . . .
Diagnostic Trouble Code (DTC) P0406
EGR High Voltage 6E±231. . . . . . . . . . . . . . . . . . . . . .
Diagnostic Trouble Code (DTC) P0502
VSS Circuit Low Input 6E±234. . . . . . . . . . . . . . . . . . .
Diagnostic Trouble Code (DTC) P0562
System Voltage Low 6E±237. . . . . . . . . . . . . . . . . . . .
Diagnostic Trouble Code (DTC) P0563
System Voltage High 6E±239. . . . . . . . . . . . . . . . . . . .
Diagnostic Trouble Code (DTC) P0601
PCM Memory 6E±240. . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnostic Trouble Code (DTC) P1154
HO2S Circuit Transition Time Ratio Bank 2
Sensor 1 6E±241. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnostic Trouble Code (DTC) P1171
Fuel System Lean During Acceleration 6E±245. . . .
Diagnostic Trouble Code (DTC) P1380
ABS Rough Road ABS System Fault 6E±248. . . . . .
Diagnostic Trouble Code (DTC) P1404
EGR Closed Stuck 6E±249. . . . . . . . . . . . . . . . . . . . . .
Diagnostic Trouble Code (DTC) P1508
IAC System Low RPM 6E±251. . . . . . . . . . . . . . . . . . .
Diagnostic Trouble Code (DTC) P1509
IAC System High RPM 6E±254. . . . . . . . . . . . . . . . . .
Diagnostic Trouble Code (DTC) P1618
Serial Peripheral Interface (SPI) PCM
Interprocessor Communication Error 6E±257. . . . . .
Diagnostic Trouble Code (DTC) P1625
PCM Unexpected Reset 6E±258. . . . . . . . . . . . . . . . .
Diagnostic Trouble Code (DTC) P1640
Driver-1-Input High Voltage 6E±259. . . . . . . . . . . . . .
Symptom Diagnosis 6E±262. . . . . . . . . . . . . . . . . . . . .
Default Matrix Table 6E±288. . . . . . . . . . . . . . . . . . . . .
Camshaft Position (CMP) Sensor 6E±291. . . . . . . . . .
Crankshaft Position (CKP) Sensor 6E±292. . . . . . . . .
Engine Coolant Temperature (ECT) Sensor 6E±292.
Heated Oxygen Sensor (HO2S) 6E±293. . . . . . . . . . .
Intake Air Temperature (IAT) Sensor 6E±295. . . . . . .
Knock Sensor (KS) 6E±296. . . . . . . . . . . . . . . . . . . . . . Mass Air Flow (MAF) Sensor 6E±297. . . . . . . . . . . . .
Manifold Absolute Pressure (MAP) Sensor 6E±297.
Malfunction Indicator Lamp (MIL) 6E±298. . . . . . . . . .
Powertrain Control Module (PCM) 6E±298. . . . . . . . .
EEPROM 6E±300. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Steering Pressure (PSP) Switch 6E±300. . . .
Throttle Position (TP) Sensor 6E±301. . . . . . . . . . . . .
Vehicle Speed Sensor (VSS) 6E±302. . . . . . . . . . . . .
Air Cleaner/Air Filter 6E±303. . . . . . . . . . . . . . . . . . . . .
Idle Air Control (IAC) Valve 6E±304. . . . . . . . . . . . . . .
Common Chamber 6E±305. . . . . . . . . . . . . . . . . . . . . .
Accelerator Cable Assembly 6E±305. . . . . . . . . . . . . .
Accelerator Pedal Replacement 6E±308. . . . . . . . . . .
Fuel Filter Cap 6E±310. . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel Filter 6E±310. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel Gauge Unit 6E±313. . . . . . . . . . . . . . . . . . . . . . . .
Fuel Injectors 6E±314. . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel Pressure Regulator 6E±315. . . . . . . . . . . . . . . . .
Fuel Metering System 6E±317. . . . . . . . . . . . . . . . . . . .
Fuel Pump Assembly 6E±318. . . . . . . . . . . . . . . . . . . .
Fuel Pump Relay 6E±319. . . . . . . . . . . . . . . . . . . . . . . .
Fuel Rail Assembly 6E±319. . . . . . . . . . . . . . . . . . . . . .
Fuel Tank 6E±321. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Throttle Body (TB) 6E±323. . . . . . . . . . . . . . . . . . . . . . .
Electronic Ignition System 6E±324. . . . . . . . . . . . . . . .
Catalytic Converter 6E±325. . . . . . . . . . . . . . . . . . . . . .
Air Conditioning Relay 6E±325. . . . . . . . . . . . . . . . . . .
EVAP Canister Hoses 6E±326. . . . . . . . . . . . . . . . . . . .
EVAP Canister 6E±326. . . . . . . . . . . . . . . . . . . . . . . . . .
EVAP Canister Purge Solenoid 6E±327. . . . . . . . . . . .
Fuel Tank Vent Valve 6E±328. . . . . . . . . . . . . . . . . . . .
Linear Exhaust Gas Recirculation
(EGR) Valve 6E±328. . . . . . . . . . . . . . . . . . . . . . . . . . .
Positive Crankcase Ventilation (PCV) Valve 6E±329.
Wiring and Connectors 6E±330. . . . . . . . . . . . . . . . . . .
PCM Connectors and Terminals 6E±330. . . . . . . . . . .
Wire Harness Repair: Twisted Shielded
Cable 6E±330. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Twisted Leads 6E±331. . . . . . . . . . . . . . . . . . . . . . . . . .
Weather-Pack Connector 6E±332. . . . . . . . . . . . . . . . .
Com-Pack III 6E±333. . . . . . . . . . . . . . . . . . . . . . . . . . .
Metri-Pack 6E±333. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General Description 6E±335. . . . . . . . . . . . . . . . . . . . .
General Description (PCM and Sensors) 6E±335. . .
58X Reference PCM Input 6E±335. . . . . . . . . . . . . .
A/C Request Signal 6E±335. . . . . . . . . . . . . . . . . . . .
Crankshaft Position (CKP) Sensor 6E±335. . . . . . .
Camshaft Position (CMP) Sensor and
Signal 6E±335. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Coolant Temperature (ECT) Sensor 6E±335
Electrically Erasable Programmable Read
Only Memory (EEPROM) 6E±336. . . . . . . . . . . . . .
Fuel Control Heated Oxygen Sensors 6E±336. . . .
Intake Air Temperature (IAT) Sensor 6E±336. . . . .

6E±5 ENGINE DRIVEABILITY AND EMISSIONS
Specifications
Tightening Specifications
ApplicationN´mLb Ft.Lb In.
Camshaft Position Sensor Retaining Screw9Ð78
Crankshaft Position Sensor Mounting Bolt10Ð87
EGR Bolt2821Ð
EGR Nut2821Ð
Engine Coolant Temperature Sensor207.7Ð
Fuel Drain Plug2922Ð
Fuel Pressure Regulator Attaching Screw6.5Ð60
Fuel Rail Bolts2518Ð
Fuel Tank Undercover Retaining Bolts3627Ð
Heated Oxygen Sensor4231Ð
Lower Intake Manifold to Engine Block Bolts2518Ð
Lower Intake Manifold to Engine Block Nuts2518Ð
Spark Plugs1813Ð
Throttle Body Mounting Bolts2518Ð
Upper Intake Manifold to Lower Intake Manifold Bolts2518Ð
VSS Retaining Bolt13Ð120
Vehicle Type Specifications
ECAUSTRALIA
THAILAND
SOUTH-EA
ST-ASIA
LATIN
AMERICAGULF
CONTRIES
SAUDI
CHINASOU
TH
AFRI
CA
EXPORTSpecifications
UBSUBSUBSUBSUBSUBS
OBD
O2
SENCATEGRMTATMTATMTATMTATMTMTATOBDSEN
SORAEGR
wI21

wI21

w11

w11

w11

w11

w1

w1

w
wI
w

6E±24
ENGINE DRIVEABILITY AND EMISSIONS
PCM Pinout Table, 32-Way Blue Connector ± Row ªEº
(For except EXPORT and SOUTH AFRICA)
TS23346
PINPIN FunctionWire ColorIGN ONENG RUNRefer To
E1Transmission Output Shaft
Sensor (TOSS) HighRED0.0 V0.1 VAutomatic Transmission
(4L30E)
E2Transmission Output Shaft
Sensor (TOSS) LowWHT0.0 V0.0 VAutomatic Transmission
(4L30E)
E3Pressure Control Solenoid
LowPPL/RED0.0 V1.1 VAutomatic Transmission
(4L30E)
E4Pressure Control Solenoid
HighPPL/WHT0.0 V4.9 VAutomatic Transmission
(4L30E)
E5Exhaust Gas Recirculation
(EGR) Control HighBLK/YELB+B+General Description and
Operation, EGR Control
E6Exhaust Gas Recirculation
(EGR) Control LowYELB+B+General Description and
Operation, EGR Control
E7Transmission Range
Signal ªBºBLU/YEL0.0 V0.0 VAutomatic Transmission
(4L30E)
E8Throttle Position (TP)
SensorBLU0.5-0.8 V0.5-0.8 V
(at idle)General Description and
Operation, Throttle Position
Sensor
E9Engine Coolant
Temperature (ECT)
SensorBLU/RED0.5-4.9 V
(depends on
temperature)0.5-4.9 V
(depends on
temperature)General Description and
Operation, Engine Coolant
Temperature (ECT) Sensor
E10Not UsedÐÐÐÐ
E11Crankshaft Position (CKP)
Sensor +5 Volt ReferenceYEL/RED5.0 V or less
than 1.0 V5.0 VGeneral Description and
Operation, Crankshaft
Position Sensor
E12Transmission Range
Signal ªAºBLU/WHTB+B+Automatic Transmission
(4L30E)
E13Fuel Pump (FP) RelayRED/WHT0.0 VB+On-Vehicle Service, Fuel
Pump Relay
E14Shift High (BAND APPLY)BRN/WHTB+B+Automatic Transmission
(4L30E)