display JAGUAR X308 1998 2.G Workshop Manual

JAGUAR X308 1998 2.G Workshop Manual X308 1998 2.G JAGUAR JAGUAR https://www.carmanualsonline.info/img/21/7640/w960_7640-0.png JAGUAR X308 1998 2.G Workshop Manual

Page 45 of 2490

JAGUAR X308 1998 2.G Workshop Manual High
 tension (electrical)
ht
Hourh
Hydro

carbon
HC
I 
Idl

e Air Control
IACEl
 ectrical control of throttle bypass air
Idl

e Air Control Valve
IACVStepper motor dri
 ven device which vari
es the v

Page 48 of 2490

JAGUAR X308 1998 2.G Workshop Manual  
 
Tacho
 meter
TACHA 
ci
 rcuit that provides input for 
an electronic tachometer display
Thermal Vacuu
 m Valve
TVVControls vacuum l
e
 vels or 
routing based on temperature
Throttle
  Body
TBDe
vi

Page 49 of 2490

JAGUAR X308 1998 2.G Workshop Manual Identification
 Codes - 
Identification Codes 
Descr
 iption and Operation 
En

gine Number 
The en
 gine number (10 digits) is stamped on a raised pad on th
e front of the engine block near the therm

Page 50 of 2490

JAGUAR X308 1998 2.G Workshop Manual  
Date of
  Manufacture 
T
h
 e date of manufacture (Build Date) of a vehicle is define
d as the calendar month and year in which the bodyshell and 
powertrain are combined and the completed vehicle l

Page 54 of 2490

JAGUAR X308 1998 2.G Workshop Manual  
Wh en t
 he vehicle is being reco
vered by rear suspended tow: 
The ignition key must be remo ved from the ig
 nition switch to lock the stee
ring with the front wheels facing straight 
ahead.

Page 276 of 2490

JAGUAR X308 1998 2.G Workshop Manual Is hard-wi
 red to the instrume
nt cluster message center.  
Is hard
 -wired to the J1962 diagnostic connector.  
Op
era
 tion 
Th
e
  system selects the soft or 
firm damper setting according t

Page 431 of 2490

JAGUAR X308 1998 2.G Workshop Manual  
The brake 
 control modulator comprises: 
a A

BS/TCCM  
a h

ydraulic control unit,  
an electrically driven hydrau

lic pump,  
two low pressure accumulato

rs and damping chambers.

Page 437 of 2490

JAGUAR X308 1998 2.G Workshop Manual Make sure the ignition is turned off. 1 
Meas
 ure the resistances between LF27,
 pins 08 and 24 (B) and ground. 
2 
Are
  the resistances less than 5 ohms? 
Yes  The power and ground supplies to the

Page 438 of 2490

JAGUAR X308 1998 2.G Workshop Manual Make sure the ignition is off. 1 
Disc
 onnect the ABS module connector, LF27. 
2 
M
e
 asure the resistance between LF27, pin 17 (W) and FL01, pin 02 (W). 
3 
I
s
  the resistance less than 5 ohms?

Page 439 of 2490

JAGUAR X308 1998 2.G Workshop Manual  
 
Spin
 the wheel by hand and check the meter display. 
3 
Doe

s the sensor generate a voltage?  
Yes  GO to E2
.  
No
  
If the WSS ring is in good condition, install a new WSS.  
REFER to:  Rear
Page:   1-10 11-20 21-30 31-40 41-50 ... 60 next >