seat JAGUAR XFR 2010 1.G Workshop Manual

Seating - Front Seat
Removal and Installation Published: 11-May-2011

Removal

1. Make the air bag supplemental restraint system (SRS) safe.
For additional information, refer to: Standard Workshop Practices (100-00 General Information, Description and Operation).


2. NOTE: Right-hand shown, left-hand similar.

Position the front seat fully forwards.
Lower the front seat head restraint to the fully
lowered position.




















3. NOTE: Right-hand shown, left-hand similar.
Remove the safety belt lower anchor trim panel.

4. NOTE: Right-hand shown, left-hand similar. Release the
safety belt lower anchor from the front seat.





















5. NOTES:


Left-hand shown, right-hand similar.


Some variation in the illustrations may occur, but the
essential information is always correct.
Remove the 2 rear bolts from the front seat.







6. Position the front seat fully rearwards.


7. NOTE: Left-hand shown, right-hand similar.
Remove the 2 front bolts from the front seat.










8. Reposition the front seat to the central position.

9. Disconnect the battery ground cable.
For additional information, refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).

10. Disconnect the front seat harness electrical connectors.
Tilt the front seat rearwards to aid disconnecting the
front seat electrical connectors.












11. NOTES:


Make sure no damage is caused to the vehicle trim when
removing the front seat.


Left-hand shown, right-hand similar.
Remove the front seat.






Installation

1. To install, reverse the removal procedure.
TORQUE: 47 Nm













2. NOTE: Some variation in the illustrations may occur, but
the essential information is always correct.
TORQUE: 47 Nm

Seating - Front Seat Backrest
Removal and Installation Published: 11-May-2011

Removal

1. Make the air bag supplemental restraint system (SRS) safe.
For additional information, refer to: Standard Workshop Practices (100-00 General Information, Description and Operation).

2. Disconnect the battery ground cable.
For additional information, refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).

3. Remove the front seat.
For additional information, refer to: Front Seat (501-10 Seating, Removal and Installation).


4. WARNING: This step requires the aid of another
technician.


CAUTION: Take extra care when handling the
component.
Remove the front seat backrest assembly.






















5. Remove the front seat backrest cover.
For additional information, refer to: Front Seat Backrest Cover (501-10 Seating, Removal and Installation).

6. Remove the backrest halo panel.
Release the 5 wiring harness clips.


7. NOTE: Do not disassemble further if the component is removed for
access only.
Remove the front seat recliner motor.
For additional information, refer to: Front Seat Recliner Motor (501-10,

Removal and Installation).

8. Remove the lumbar assembly.
For additional information, refer to: Lumbar Assembly (501-10 Seating, Removal and Installation).

9. Remove the front seat head restraint motor.
For additional information, refer to: Front Seat Head Restraint Motor (501-10 Seating, Removal and Installation).

Installation

1. To install, reverse the removal procedure.
TORQUE: 35 Nm













2. If a new component has been installed, configure using Jaguar approved
diagnostic equipment.

Seating - Front Seat Backrest Cover
Removal and Installation
Removal Published: 11-May-2011

1. Make the air bag supplemental restraint system (SRS) safe.
For additional information, refer to: Standard Workshop Practices (100-00 General Information, Description and Operation).

2. Remove the front seat.
For additional information, refer to: Front Seat (501-10 Seating, Removal and Installation).

3. Remove the side air bag module.
For additional information, refer to: Side Air Bag Module (501-20B Supplemental Restraint System, Removal and Installation).


4. NOTE: If equipped.
Reposition the front seat backrest thermo-electric device.














5. NOTE: If equipped.
Release the front seat backrest thermo-electric device duct











6. NOTE: If equipped.

Remove the front seat backrest thermo-electric device
retaining screws.

7. NOTE: If equipped.

Remove the front seat backrest thermo-electric device.
Disconnect the electrical connector.










8. Remove the front seat head restraint.

9. Remove the front seat head restraint motor.
For additional information, refer to: Front Seat Head Restraint Motor (501-10 Seating, Removal and Installation).


10. NOTE: Some variation in the illustrations may occur,
but the essential information is always correct.

Using a suitable tool, remove the front seat head restraint
guide sleeves.

11. Remove the front seat backrest cushion and cover from the front seat
frame.












12.
13. Remove and discard the hog rings.
Remove the 22 hog rings.















Remove the front seat backrest cover.













Installation

1. NOTES:


Make sure that new hog rings are installed.


Use hog ring pliers to close the hog rings. Do not use any
other tool. The hog rings must be closed to overlap as
illustrated.
To install, reverse the removal procedure. www.JagDocs.com

Seating - Front Seat Bolster
Removal and Installation

Removal

NOTES:


Removal steps in this procedure may contain installation details.


Some variation in the illustrations may occur, but the essential information is always correct. Published: 11-May-2011

1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).

2. Refer to: Front Seat Backrest Cover (501-10 Seating, Removal and Installation).






Installation

3.

























4. WARNING: The procedure must be carried out on both
sides of the seat.


CAUTION: Make sure that the clips are correctly
located.

1. To install, reverse the removal procedure.

Seating - Front Seat Bolster Pump
Removal and Installation

Removal

NOTES:


Removal steps in this procedure may contain installation details.


Some variation in the illustrations may occur, but the essential information is always correct. Published: 11-May-2011

1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).

2. Refer to: Front Seat Backrest Cover (501-10 Seating, Removal and Installation).
3.
Installation

1. To install, reverse the removal procedure.