U3000-87 JAGUAR XFR 2010 1.G Workshop Manual

DTC Description Possible Causes Action B1A10-1A
Speaker #10 - Circuit
resistance below
threshold
Left subwoofer
speaker circuit -
Resistance below
threshold
Carry out any pinpoint tests associated with this DTC
using the manufacturer approved diagnostic system B1A10-49
Speaker #10 -
Internal electronic
failure
Internal electronic
failure
Suspect the audio amplifier module, check and install a
new module as required, refer to the new
module/component installation note at the top of the
DTC Index B1A11-11
Speaker #11 - Circuit
short to ground
Right subwoofer
speaker circuit - Short
to ground
Refer to electrical circuit diagrams and check right
subwoofer speaker circuit for short to ground B1A11-12
Speaker #11 - Circuit
short to battery
Right subwoofer
speaker circuit - Short
to power
Refer to electrical circuit diagrams and check right
subwoofer speaker circuit for short to power B1A11-13
Speaker #11 - Circuit
open
Right subwoofer
speaker circuit - Open
circuit
Refer to electrical circuit diagrams and check right
subwoofer speaker circuit for open circuit B1A11-1A
Speaker #11 - Circuit
resistance below
threshold
Right subwoofer
speaker circuit -
Resistance below
threshold
Carry out any pinpoint tests associated with this DTC
using the manufacturer approved diagnostic system B1A11-49
Speaker #11 -
Internal electronic
failure
Internal electronic
failure
Suspect the audio amplifier module, check and install a
new module as required, refer to the new
module/component installation note at the top of the
DTC Index U2003-98
Fibre Optic
Communication Bus -
Component or system
over temperature
Component or system
over temperature
Clear DTC and allow system to cool, monitor for
re-occurrence of DTC U3000-05
Control module -
System programming
failures
Software
incompatibility
The version of the
Local Configuration
file does not match
that expected
Re-configure the audio amplifier as an existing control
module, using the manufacturer approved diagnostic
system U3000-42
Control module -
General memory
failure
General memory
failure
Re-configure the audio amplifier as an existing control
module, using the manufacturer approved diagnostic
system. Clear DTC, cycle ignition and read DTCs. If DTC
returns, suspect audio amplifier module and install a
new module. Refer to the new module/component
installation note at the top of the DTC Index U3000-44
Control module - Data
memory failure
Data memory failure
Re-configure the audio amplifier as an existing control
module, using the manufacturer approved diagnostic
system. Clear DTC, cycle ignition and read DTCs. If DTC
returns, suspect audio amplifier module and install a
new module. Refer to the new module/component
installation note at the top of the DTC Index U3000-55
Control Module - Not
configured
Incorrect car
configuration data
received
Check/up-date Car Configuration File using manufacturer
approved diagnostic system U3000-87
Control Module -
Missing message
Missing message
Check CJB for DTCs and refer to DTC Index. Check
information and entertainment module for Car
Configuration File and MOST network DTCs and refer to
relevant DTC Index. Carry out MOST/CAN network tests
using the manufacturer approved diagnostic system

DTC Description Possible Causes Action C1B15-13
Sensor Supply
Voltage B - Circuit
open
RECIRC servo motor
and EVAP sensor
ground circuits - open
circuit
Refer to the electrical circuit diagrams and check RECIRC
servo motor and EVAP sensor ground circuits for open
circuit P0530-11
A/C Refrigerant
Pressure Sensor A
Circuit - Circuit
short to ground
Air conditioning
pressure sensor signal
circuit - short to ground
Refer to the electrical circuit diagrams and check air
conditioning pressure sensor signal circuit for short to
ground P0530-15
A/C Refrigerant
Pressure Sensor A
Circuit - Circuit
short to battery or
open
Air conditioning
pressure sensor signal
circuit - short to power,
open circuit
Carry out any pinpoint tests associated with this DTC using
the manufacturer approved diagnostic system. Refer to the
electrical circuit diagrams and check air conditioning
pressure sensor signal circuit for short to power, open
circuit U0010-88
Medium Speed
CAN
Communication
Bus - Bus off
Bus off
Carry out any pinpoint tests associated with this DTC using
the manufacturer approved diagnostic system U0300-00
Internal Control
Module Software
Incompatibility -
No sub type
information
Invalid configuration
message is received
Re-configure the RJB using the manufacturer approved
diagnostic system. Clear the DTC and retest. If the DTC is
still logged suspect the climate control module, refer to the
new module/component installation note at the top of the
DTC Index U1A14-49
CAN Initialisation
Failure - Internal
electronic failure
Internal electronic
failure
Suspect the climate control module, check and install a
new module as required, refer to the new
module/component installation note at the top of the DTC
Index U3000-55
Control Module -
Not configured
Incorrect car
configuration data
received
Re-configure the RJB using the manufacturer approved
diagnostic system. Clear DTC and re-test. If the DTC
remains suspect the climate control module. Check and
install a new module as required, refer to the new
module/component installation note at the top of the DTC
Index U3000-87
Control Module -
Missing message
Missing message
Re-configure the RJB using the manufacturer approved
diagnostic system. Check climate control module for DTCs
and refer to the DTC Index. Carry out CAN network integrity
tests using the manufacturer approved diagnostic system.
If DTC remains suspect the climate control module. Check
and install a new module as required, refer to the new
module/component installation note at the top of the DTC
Index U3002-81
Vehicle
Identification
Number - Invalid
serial data
received
Vehicle/component
mis-match. Corrupt VIN
data being transmitted,
module previously
installed to other
vehicle
Check and install original/new module as required, refer to
the new module/component installation note at the top of
the DTC Index www.JagDocs.com

DTC Description Possible Causes Action U3000-55
Stored vehicle
configuration data does not
match - Not configured
Incorrect car configuration data
received
Re-configure the RJB using the
manufacturer approved diagnostic system.
Clear DTC and re-test. If the DTC remains
suspect the DSM, refer to the new module
installation note at the top of the DTC
Index U3000-87
Control Module - Missing
message
Missing message
Re-configure the RJB using the
manufacturer approved diagnostic system.
Check DSM for DTCs and refer to the DTC
Index. Check CAN network integrity using
the manufacturer approved diagnostic
system U3001-46
Control module improper
shutdown -
Calibration/parameter
memory failure
Calibration/parameter memory
failure
Check for DTCs that could indicate power
failure to the module and refer to the DTC
Index U3002-81
Vehicle Identification
Number (VIN) - Invalid
serial data received
Vehicle/component mis-match.
Corrupt VIN data being
transmitted, module previously
installed to other vehicle
Install original module, check for DTCs and
refer to relevant DTC Index U3003-16
Battery Voltage - Circuit
voltage below threshold
Circuit voltage below threshold
Carry out any pinpoint tests associated
with this DTC using the manufacturer
approved diagnostic system U3003-17
Battery Voltage - Circuit
voltage above threshold
Circuit voltage above threshold
Carry out any pinpoint tests associated
with this DTC using the manufacturer
approved diagnostic system

DTC Description Possible Causes Action B1D79-13
Microphone Input -
Circuit open
Microphone input circuit -
high resistance
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Refer to the electrical circuit diagrams and
test microphone input circuits for high resistance B1134-11
Phone Input - Circuit
short to ground
Phone input circuit - short
to ground
Refer to the electrical circuit diagrams and test
phone input circuits for short to ground B1134-12
Phone Input - Circuit
short to battery
Phone input circuit - short
to power
Refer to the electrical circuit diagrams and test
phone input circuits for short to power B1134-13
Phone Input - Circuit
open
Phone input circuit - high
resistance
Refer to the electrical circuit diagrams and test
phone input circuits for high resistance U2100-00
Initial Configuration
Not Complete - No
sub type information
Car configuration data not
received
Check RJB for related DTCs and refer to the relevant
DTC Index U2101-00
Control Module
Configuration
Incompatible - No sub
type information
Incorrect car configuration
data received
Check RJB for related DTCs and refer to the relevant
DTC Index. Check/amend Car Configuration File
using the manufacturer approved diagnostic system U3000-49
Control Module -
Internal electronic
failure
Internal electronic failure
Suspect the integrated audio module, install a new
module as required, refer to the new module
installation note at the top of the DTC Index U3000-55
Control Module - Not
configured
Incorrect car configuration
data received
Re-configure the RJB using the manufacturer
approved diagnostic system. Clear DTC and re-test.
If the DTC remains suspect the integrated audio
module, refer to the new module installation note
at the top of the DTC Index U3000-87
Control Module -
Missing message
Missing message
Re-configure the RJB using the manufacturer
approved diagnostic system. Check integrated audio
module for DTCs and refer to the DTC Index. Check
CAN network integrity using the manufacturer
approved diagnostic system U3000-98
Control Module -
Component or system
over temperature
Component or system over
temperature
Check for additional DTCs and refer to DTC Index.
Clear DTC and re-test/monitor condition U3003-62
Battery Voltage -
Signal compare failure
Mis-match in battery
voltage, of 2 volts or more,
between integrated audio
module and RJB
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system

DTC Description Possible Causes Action B1A89-12
Satellite Antenna -
Circuit short to
battery
Satellite antenna circuit -
short to power
Refer to the electrical circuit diagrams and check
satellite antenna circuit for short circuit to power. Repair
wiring harness as required. Clear DTC and retest B1A89-13
Satellite Antenna -
Circuit open
Satellite antenna circuit -
open circuit, high
resistance
Refer to the electrical circuit diagrams and check
satellite antenna circuit for open circuit, high
resistance. Repair wiring harness as required. Clear DTC
and retest U3000-04
Control Module -
System internal
failures
System internal failure
Check and install a new satellite radio module as
required. Refer to the warranty policy and procedures
manual, or determine if any prior approval programme is
in operation, prior to the installation of a new
module/component U3000-4A Control Module -
Satellite radio module -
Using the manufacturer approved diagnostic system Incorrect component Incorrect component select the vehicle configuration main menu>vehicle installed installed configuration>display and modify the vehicle Car configuration configuration file data mismatch Check update as required U3000-55
Control Module -
Not configured
Satellite radio module -
Incorrect component
installed
Incorrect car configuration
file data received
Using the manufacturer approved diagnostic system
select the vehicle configuration main menu>select
configure existing modules menu and program the
satellite radio module U3000-87
Control Module -
Missing message
The satellite radio module
has not received the
configuration file
Master module not
transmitting configuration
file
Using the manufacturer approved diagnostic system
check that the satellite radio module is configured
correctly
Check that the configuration file is being transmitted by
the master module
Using the manufacturer approved diagnostic system,
complete a MOST network integrity test U3000-98
Control Module -
Component or
system over
temperature
Satellite radio module
cooling vents obstructed
Wiring harness fault
Internal electronic failure
Check for possible causes of the satellite radio module
overheating. Check that the ventilation is not
obstructed
Check for short circuit related DTCs. Refer to the
electrical circuit diagrams and check ground circuit for
high resistance. Check antenna circuit for short to power
or ground. Repair wiring harness as required. Clear DTC
and retest
Check for internal electronic failure related DTCs
If fault persists, check and install a new satellite radio
module. Refer to the warranty policy and procedures
manual, or determine if any prior approval programme is
in operation, prior to the installation of a new
module/component U3003-62
Battery Voltage -
Signal compare
failure
Signal compare failure
Satellite radio module
voltage differs more than
±2V compared to rear
junction box voltage
Refer to relevant section of workshop manual and
battery care manual. Check battery state of charge and
starting/charging system performance. Check power
supply circuit from rear junction box to satellite radio
module
Refer to electrical circuit diagrams and check the power
and ground supply circuits to the module. Repair wiring
harness as required. Clear DTC and retest

DTC Description Possible Causes Action check CAN Network B100D-87
Column Lock
Authorisation -
Missing message
Missing message
CAN fault
No response from
electric steering column
lock control module,
instrument cluster,
central junction box
Battery voltage at
electric steering column
lock control module too
low
Electric steering column
lock control module,
instrument cluster,
central junction box fault
NOTE: Prior to clearing this DTC, carry out the Vehicle
Functional Reset application using the manufacturer approved
diagnostic system

Clear DTC, repeatedly lock and unlock car using the key
fob and retest. Check for related DTCs and refer to the
relevant DTC index
If the fault is cleared, notify the customer that the
steering column lock may fail to unlock if the vehicle is
parked with a high steering angle or with the road wheel
against a curb. If the column lock is failing to disengage,
the customer may be able to rectify this by rotating the
steering wheel while pressing the engine start button
If fault persists, complete a CAN network integrity test
using the manufacturers approved diagnostic system.
Alternatively, refer to the electrical circuit diagrams and
check CAN circuits between the central junction box, the
instrument cluster and the electronic steering column
lock. Refer to the electrical circuit diagrams and check the
central junction box, the instrument cluster and the
electronic steering column lock power and ground supply
circuits for short circuit to ground, short circuit to power,
open circuit, high resistance. Repair circuit(s) as required.
Clear DTC, perform an on demand self-test and retest
If fault persists, check that the vehicle battery supply
voltage is between 9-16 volts. Rectify as required U0001-88
High Speed CAN
Communication
Bus - Bus off
Bus off
Refer to the electrical circuit diagrams and check the
power and ground connections to the module. Using the
manufacturer approved diagnostic system, complete a
CAN network integrity test. Refer to the electrical circuit
diagrams and check the CAN network U0300-00
Internal Control
Module Software
Incompatibility -
No sub type
information
No sub type information
Refer to network communication section of the workshop
manual. Clear the DTC and ensure the vehicle battery
supply voltage is between 9-16Volts. Using the
manufacturers approved diagnostic system, complete a
CAN integrity test. Perform an on demand self-test and
retest U3000-49
Control Module -
Internal electronic
failure
Internal electronic
failure detected during
self test or lock/unlock
operation
Refer to network communication section of the workshop
manual. Clear the DTC and ensure the vehicle battery
supply voltage is between 9-16Volts. Perform an on
demand self-test and if the DTC returns suspect the
electric steering column lock, refer to the warranty policy
and procedures manual if a module/component is suspect U3000-87
Control Module -
Missing message
Configuration message
not received
Refer to the electrical circuit diagrams and check the
power and ground connections to the module. Using the
manufacturer approved diagnostic system, complete a
CAN network integrity test. Refer to the electrical circuit
diagrams and check the CAN network. Check modules are
configured correctly using the manufacturer approved
diagnostic system U3002-81
Vehicle
Identification
Number - Invalid
serial data
received
Invalid vehicle
identification number
Confirm the correct VIN details are stored in Steering
Column Lock Module using the approved diagnostic
system

DTC Description Possible Causes Action U0300-00
Internal Control Module
Software Incompatibility -
No sub type information
Incompatible tire
pressure monitoring
system module for
vehicle CAN network
Check correct tire pressure monitoring system
module is installed to vehicle specification,
otherwise suspect the rear junction box U0415-00
Invalid Data Received
From Anti-Lock Brake
System (ABS) Control
Module - No sub type
information
Invalid data received
from the anti-lock braking
system control module
CAN bus fault
Anti-lock braking system
fault
Check anti-lock braking system control module
and Instrument Cluster for related DTCs and refer
to the relevant DTC index. Carry out CAN network
integrity tests U0424-00
Invalid Data Received
From HVAC Control
Module - No sub type
information
HVAC control module
fault
Check climate control module for related DTCs
and refer to relevant DTC index U1A14-49 CAN Initialisation Failure
- Internal electronic
failure
Tire pressure monitoring
system module fault
Install a new tire pressure monitoring module.
Refer to the new module/component installation
note at the top of the DTC index U3000-55
Control Module - Not
configured
Tire pressure monitoring
system configuration data
is invalid
Check and amend the car configuration file U3000-87
Control Module - Missing
message
Tire pressure monitoring
system configuration data
not received
Check the rear junction box for related DTCs and
refer to the relevant DTC index. Carry out CAN
network integrity test U3002-81
Vehicle Identification
Number - Invalid serial
data received
Tire pressure monitoring
system module and
vehicle VIN mismatch
NOTE: This DTC indicates that the tire pressure
monitoring system module is not the original part
installed to the vehicle at the factory/dealer and could
have been substituted. Refer to the note above the DTC
index about replacing components which may remain
under manufacturer warranty.

Re-install the original or a new tire pressure
monitoring system control module

DTC Description Possible Causes Action U3000-44
Control Module - Data
memory failure
EEPROM, External
RAM access failure
Suspect the TSD, check and install a new TSD as
required, refer to the new module/component
installation note at the top of the DTC Index U3000-48
Control Module -
Supervision software
failure
Supervision software
failure
Re-configure the TSD using the manufacturer approved
diagnostic system U3000-4B
Control Module - Over
temperature
Touch panel backlight
- high temperature
detected
Allow the system to cool, clear the DTC and
check/monitor system for re-occurrence. If DTC re-occurs
suspect the TSD. Check and install a new TSD as
required, refer to the new module/component
installation note at the top of the DTC Index U3000-55
Control Module - Not
configured
Incorrect Car
Configuration
Parameters received
Check/amend Car Configuration File using the
manufacturer approved diagnostic system U3000-87
Control Module -
Missing message
Car Configuration File
not received
Check RJB for related DTCs and refer to relevant DTC
Index. Check CAN and MOST networks, carry out the
CAN and MOST network tests using the manufacturer
approved diagnostic system U3000-98
Control Module -
Component or system
over temperature
TSD internal
temperature over
limit
Allow the system to cool, clear the DTC and
check/monitor system for re-occurrence. If DTC re-occurs
suspect the TSD. Check and install a new TSD as
required, refer to the new module/component
installation note at the top of the DTC Index U3003-16
Battery Voltage -
Circuit voltage below
threshold
Circuit voltage below
threshold
Carry out any pinpoint tests associated with this DTC
using the manufacturer approved diagnostic system U3003-17
Battery Voltage -
Circuit voltage above
threshold
Circuit voltage above
threshold
Carry out any pinpoint tests associated with this DTC
using the manufacturer approved diagnostic system

DTC Description Possible Causes Action U3000-04
Control Module -
System internal
failures
Diversity antenna amplifier internal
failure
Renew the amplifier module U3000-4A
Control Module -
Incorrect
component
installed
Diversity antenna amplifier internal
incorrect component installed
- The module has been installed to
a vehicle not configured to accept
it
Using the manufacturer approved
diagnostic system select the vehicle
configuration main menu, select configure
existing modules menu and program the
module U3000-55
Control Module -
Not configured
Diversity antenna amplifier not
configured correctly
Using the manufacturer approved
diagnostic system select the vehicle
configuration main menu, select configure
existing modules menu and program the
module U3000-87
Control Module -
Missing message
Missing message
Using the manufacturer approved
diagnostic system select the vehicle
configuration main menu, select configure
existing modules menu and program the
module U3000-98
Control Module -
Component or
system over
temperature
Diversity antenna amplifier component or
system over temperature
Consider moving the amplifier mounting
position to prevent unit overheating. Cool
the vehicle interior down by ensuring it is
in the shade and have the A/C on cool.
When cool, clear the DTC and retest. If
the problem persists, renew the amplifier
module U3003-62
Battery Voltage -
Signal compare
failure
Mismatch in battery voltage of 2 volts or
more for longer than 1 minute, between
the measured battery voltage at the
Digital Audio Control Module C and the
battery voltage signal sent from the Rear
Junction Box.
Refer to the electrical guides and check
that power supply voltage at Digital Audio
Control Module C and Rear Junction Box is
not different by more than 2 volts. Rectify
as required

DTC Description Possible Cause Action U0142-00
Lost Communication With
Body Control Module "B"
-no sub type information
CAN bus fault
Auxiliary Junction Box fault Refer to the electrical wiring diagrams and check
Auxiliary Junction Box power and ground supplies for
short, open circuit. Carry out CAN network integrity
tests. U0155-00
Lost Communications With
Instrument Panel Cluster
(IPC) Control Module-no
sub type information
CAN bus fault
Instrument cluster fault Refer to the electrical wiring diagrams and check
instrument cluster power and ground supplies for
short, open circuit. Carry out CAN network integrity
tests. U0164-00
Lost Communication With
HVAC Control Module-no
sub type information
CAN bus fault
Climate control module
fault Refer to the electrical wiring diagrams and check
climate control module power and ground supplies for
short, open circuit. Carry out CAN network integrity
tests. U0300-00
Internal Control Module
Software Incompatibility-no
sub type information
Incompatible tire pressure
monitoring system module
for vehicle CAN network Check correct tire pressure monitoring system module
is installed to vehicle specification, otherwise
suspect the Auxiliary Junction Box. U0415-00
Invalid Data Received From
Anti-Lock Brake System
(ABS) Control Module-no
subtype information
Invalid data received from
the Anti-Lock Braking
System Control Module
CAN bus fault
Anti-Lock Braking System
fault Check Anti-Lock Braking System control module and
Instrument Cluster for related DTCs and refer to the
relevant DTC Index. Carry out CAN network integrity
tests. U0424-00
Invalid Data Received From
HVAC Control Module-no
sub type information
HVAC control module fault Check climate control module for related DTCs and
refer to relevant DTC Index. U1A14-49
CAN Initialisation Failure-
internal electronic failure
Tire pressure monitoring
system module fault Install a new tire pressure monitoring module. Refer
to the new module/component installation note at
the top of the DTC Index. U3000-55
Control Module-not
configured
Tire pressure monitoring
system configuration data
is invalid Check and amend the car configuration file. U3000-87
Control Module-missing
message
Tire pressure monitoring
system configuration data
not received Check the Auxiliary Junction Box for related DTCs and
refer to the relevant DTC Index. Carry out CAN
network integrity test. U3002-81
Vehicle Identification
Number - invalid serial data
received
Tire pressure monitoring
system module and vehicle
VIN mis-match
NOTE: This DTC indicates that the tire pressure
monitoring system module is not the original part
installed to the vehicle at the factory/dealer and
could have been substituted. Refer to the note above
the DTC index about replacing components which may
remain under manufacturer warranty.

Re-install the original or a new tire pressure monitoring system control module.
Component Tests

Wheels and Tires

For wheel and tire specification information (pressures, torques, etc).

When replacing wheels or tires, local legislation regarding health and safety must be complied with.

If the vehicle has a Tire Pressure Monitoring System installed, only Jaguar approved wheels and tires should be used. If the
wheel and tire size is changed (for example from R18 to R20) the Tire Pressure Monitoring System module should be updated
with the correct pressure information appropriate to the new wheel and tire set. Update the Tire Pressure Monitoring System
module using the Jaguar approved diagnostic system.
As a general guideline, only replace tires in pairs or as a set, and only with tires of equivalent size and specification.
Confirm the symptoms of the customer complaint.
As much information as possible should be gathered from the driver to assist in diagnosing the cause(s).

1. Before a road test, carry out a basic inspection to make sure the vehicle is safe and legal to drive.

Basic inspection

Correct tire inflation
Legal tire tread depth