clock JAGUAR XJ 2004 X350 / 3.G Owners Manual
[x] Cancel search | Manufacturer: JAGUAR, Model Year: 2004, Model line: XJ, Model: JAGUAR XJ 2004 X350 / 3.GPages: 227, PDF Size: 4.22 MB
Page 40 of 227
Before Driving
Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 3
Steering Column Adjustment . . . . . . . . . . . . . . . 3 - 7
Door Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 8
Interior Rear View Mirror . . . . . . . . . . . . . . . . . . 3 - 9
Occupant Protection . . . . . . . . . . . . . . . . . . . . 3 - 11
Seat Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 11
Air Bags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 14
Child Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 23
LATCH Child Restraint System . . . . . . . . . . . . . 3 - 27
Memory Setting . . . . . . . . . . . . . . . . . . . . . . . . 3 - 31
Clock Adjustment . . . . . . . . . . . . . . . . . . . . . . . 3 - 32
Luggage Compartment . . . . . . . . . . . . . . . . . . . 3 - 33
Ski Hatch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 34
Page 71 of 227
3 - 32 Before Driving
Memory recall using an integrated
key
The integrated key will recall a memory
position when the unlock button is
pressed when set as follows:
1. Adjust the seat, steering column, pedals and exterior rear view mirrors
to the desired positions.
2. Press the M button: The red LED will illuminate for a five second period.
3. Press button ‘1’, ‘2’ or ‘3’ and then press any button on the integrated
key. Both button presses must occur
while the red LED is illuminated.
4. Repeat for the other integrated key, pressing the remaining memory
buttons.
To cancel integrated key memory recall:
1. Place a key into the ignition switch and leave in the OFF position.
2. Press the M button: The red LED will illuminate for a five second period.
3. Press any button on the integrated key
(except the panic button, if fitted) then
press the M button again. Both button
presses must occur while the red LED
is illuminated. Note:
If memory recall is performed
using an integrated ke y with the vehicle in
entry/exit position, the steering column
and seat will not return to the memorised
position until either the integrated key is
placed in the ignition switch or the
driver’s door is closed.
Driving position memory system
operating tips
• When making adjustments to a set driving position, reset the new
position in the same memory channel.
• A driving position will only be memorised during the five second
period when the red memory LED is
illuminated.
• Previous memory is erased when a new driving position is entered.
Clock Adjustment
The analogue clock is adjusted by
pressing the (+) and (–) buttons below
the dial. Pressing and holding either
button will increase the rate of hand
movement forwards or backwards as
required.
Page 75 of 227
4-4 On the Road
Engine Temperature (E)
Drive at moderate road and engine
speeds until normal operating
temperature is reached. This is indicated
when the pointer is between the
blue (cold) segment and the red (hot)
segment.
The engine operating temperature will
vary with changes in weather and engine
load. The engine temperature may rise in
some circumstances, such as:
• Idling for long periods in slow moving traffic.
• Driving up a long hill in hot weather.
• Driving slowly or stopping after driving at high speed.
• Towing a trailer or caravan.!WARNING:
1. The radiator cooling fans may continue to run after the ignition
has been switched off but will
automatically switch off when the
engine has cooled sufficiently.
2. It is unsafe to run the engine in an overheated condition.
3. Do not remove the coolant reservoir filler cap while the
engine is hot. If it is essential, then
protect your hands against
escaping steam. SLOWLY turn the
cap anti-clockwise to allow the
steam pressure to escape
completely before removing the
cap. Should the pointer move into the red
segment (
H) of the coolant gauge, stop
the vehicle as soon as it is safely possible,
turn off the engine and open the hood to
allow the engine to cool.
Page 113 of 227
4-42 On the Road
Starting/Stopping the
Vehicle
When the vehicle is stationary the
automatic gear selector may be left in ‘D’,
‘ 2 ’, ‘ 3’, ‘ 4’ or ‘ 5’, unless the vehicle is to
be parked. When stopping for traffic
lights, junctions etc., either select ‘ P’ or
apply the parkbrake and select ‘ N’.
Before Starting
Before starting the engine, new owners/
drivers should familiarize themselves with
the layout and operation of the controls
and instruments.
!WARNING:
Before attempting to start the engine,
check parkbrake is ON and gear
selector lever is in position ‘P’ or ‘N’.
To Start the Engine
The engine cannot be started until the
gear selector is in ‘ N’ or ‘ P’.
Insert the key into the ignition switch and
turn clockwise to position ‘II’ to switch
on the ignition.
When the key is turned to position ‘III’
the starter motor will turn the engine
until:
• The key is released and automatically returns to position ‘II’.
• The ignition switch is turned to ‘0’ or ‘I’.
• The gear selector is moved out of ‘P’ or ‘N’.
• The engine starts.
If the engine fails to start, the key must be
turned to position ‘0’ before attempting
to restart.
Do not use the starter continuously for
longer than six seconds. Continued use of
the starter will disc harge the battery and
may damage the starter mechanism.
Wait until the engine stops turning before
re-using the starter.
When the engine starts, release the key. The red charge light and the oil pressure
light in the instrument cluster should go
out when the engine is running.
If the engine fails to start
If an ignition key is placed in the ignition
switch and turned to position ‘II’ and the
alarm security light is flashing, it is
possible that the engine will not start.
In any event, please contact a Jaguar
Retailer to investigate the cause of the
light flashing.
It is possible that the fuel system inertia
switch may have tripped, see page 6 - 3
for the resetting procedure.
If the engine persistent
ly fails to start and
flooding is suspected, depress the
accelerator pedal fully, hold it in this
position and turn the key to position ‘III’
for six seconds. Release the key, remove
your foot from the accelerator pedal and
then attempt to restart the engine.
Note: The engine cannot start whilst the
pedal is fully depressed, it must be
released to enable the engine to start.
If the engine still fail s to start, switch the
ignition OFF and contact a Jaguar
Retailer.
Page 134 of 227
On the Road 4 - 63
Fuel and Refuelling
Before refuelling, switch off the ignition
and remove the key.
Note:Do not leave the ignition key in the
vehicle; vehicles have been stolen from
garage service/filling stations whilst the
driver is absent from the vehicle. It is
recommended that the vehicle is locked,
if left unattended.
Caution: No additives of any kind
(fuel or oil) must be put into the fuel
tank. Additives could reduce engine
life or affect exhaust emissions.
!WARNING:
1. Fuel vapour is highly flammable and in confined spaces is
explosive and toxic. In the event
of inadvertent spillage, and before
refuelling, always switch OFF the
engine. Do not use exposed flame
or light. Do not smoke. Do not
inhale fumes.
2. Do not fill the tank so that fuel is visible in the fuel filler intake
tube. This could cause spillage
and danger from exposed fuel.
Fuel Tank Filling
Caution: Your vehicle is fitted with
catalytic converters and must only be
filled with ‘Unleaded Fuel’.
The fuel filler flap release switch is
located in the knee bolster switchpack
below the fascia. The fi ller flap is on the
right-hand side of the vehicle.
A small arrow is shown on the fuel gauge
as a reminder on which side of the
vehicle the fuel filler flap is located. Open the fuel filler flap and turn the filler
cap anti-clockwise, a ¼ turn until
resistance is felt. Continue turning to
release the cap from the filler neck.
The cap is held by a retaining strap and
can be stowed over the hook on the flap
to allow easy access to fill the tank.
A warning label on the inside of the fuel
filler flap advises type/grade of fuel.
Page 135 of 227
4-64 On the Road
When filling, the dispenser nozzle must
be inserted into the filler neck sufficiently
to open the trap door for fuel to flow into
the fuel tank. For quickness and to
completely fill the ta nk, ensure that the
fuel nozzle rests on the filler neck as
shown. Fill the tank until the filler nozzle
automatically shuts off. Filling beyond
this point could result in fuel spillage.
After refuelling, refit the fuel filler cap in
to the filler neck, twist the filler cap
clockwise until it clicks and close the flap,
which automatically locks shut. The continuous use of high quality fuel
makes the need for a
dditional additives
unnecessary.
This will help to protect the engine
components against corrosion, carbon
deposit formation and prevent the fuel
injection system from clogging.
If in doubt your local Jaguar Retailer will
advise on which fuel must be used in
your vehicle.
Fuel requirements
The filler neck of the fuel tank is a small
diameter to suit the unleaded fuel pump
nozzle and will prevent the larger
diameter leaded fuel nozzle from entering
the filler neck.
Note: Not all countries have a small
diameter nozzle, for example, Japan,
so care must be taken to only fill the tank
with unleaded fuel.
Page 158 of 227
Roadside Emergency 6 - 7
Locking Wheel Nuts
Where Jaguar locking wheel nuts are
fitted (one on each wheel), they can only
be removed using the correct key socket.
The locking wheel nut comprises two
grooved parts, front and rear, which must
be turned together to allow the nut to be
fitted or removed.
To remove the nut, the front and rear
grooves must be aligned. Locate the key
socket in the grooves and push it fully
over both parts of the nut. Fit the wheel
nut wrench over the key socket and
loosen the locking wheel nut (turn anti-
clockwise). Attempting to remove the nut without the
correct key socket
(such as attempted
theft) or with the socket not located over
the rear part of the nut, will cause the
front part only ( A) to turn.
If this has happened, rotate the front part
with the key socket until the grooves are
re-aligned and then push the socket fully
over the nut.
Should a new key socket be required,
contact your Jaguar Retailer. Proof of
vehicle ownership will be required.
Page 161 of 227
6 - 10 Roadside Emergency
!WARNING:
1. Do not attempt to lift the vehicle unless the jack head is fully
engaged in the jacking point.
2. Ensure that the parkbrake is applied.
Place the jack squarely beneath the
appropriate jacking point. Ensure that the
jack head is fully engaged. Carefully raise
the vehicle by turning the handle.
Stop jacking the vehicle when the tyre
just clears the ground. Minimum tyre lift
gives maximum vehicle stability.
Remove the wheel nuts and the wheel.
Centre badge
When changing the alloy road wheels,
transfer the centre badge to the
replacement wheel. Using the plastic
tipped end of the wheel nut wrench
handle from the inside of the wheel, push
the centre badge from its housing.
Push the centre badge into the
replacement wheel. Fitting the spare wheel
Fit the spare wheel and loosely secure
with the wheel nuts.
Using the wheel nut wrench, lightly
tighten the wheel nuts
alternately using
the sequence shown in the illustration.
Lower the jack and ti ghten the wheel nuts
alternately, DO NOT OVER TIGHTEN.
At the earliest opportunity have the
wheel nuts tightened with a torque
wrench to 92 lb.ft (125 Nm).
This torque must not be exceeded. Stowing the equipment
Stow the replaced road wheel in the
trunk.
Check that the locking ring is unscrewed
fully so that it is as close as possible to the
handle of the wheel retainer. This is to
ensure that the wheel retainer can be
fitted correctly.
Locate the wheel retainer into its mating
thread in the trunk floor and tighten it
fully, then tighten the locking ring
clockwise to secure the wheel.
Seepage6-8.
Stow the jacking equipment.
Close the trunk floor panel.
!WARNING:
When a temporary spare wheel is
fitted, drive with caution and replace
with the specified wheel and tyre as
soon as possible.
Page 164 of 227
Roadside Emergency 6 - 13
Towing Eye
A screw-in towing eye is provided in the
trunk with the jack and can be fitted to
the front or rear of the vehicle.
The towing eye has a left-hand thread
and must be turned in an anti-clockwise
direction when fitting.
Caution:
1. The towing eye is not suitable for ‘solid bar’ towing.
2. Care must be taken to avoid damaging the bumpers and front
apron. Front tow point
The front tow point is located behind a
plastic cover (shown
above) on the left-
hand side of the vehicle, as viewed from
the front.
To remove the cover, unclip the top edge,
pivot down and unclip the bottom edge.
Screw the towing ey e into the vehicle,
right up to the shoulder, turning anti-
clockwise.
To refit the cover (towing eye removed)
first clip the lower edge to the bumper
aperture, pivot up and press the top edge
into position. Rear tow point
!WARNING:
Avoid body contact with a hot
exhaust pipe when fitting the eye to
the rear towing point.
The rear tow point is alongside the left-
hand exhaust pipe.
Screw the towing eye into the vehicle,
right up to the shoulder, turning anti-
clockwise.
Page 166 of 227
Roadside Emergency 6 - 15
Dipped beam (outer) headlights
Caution: Halogen bulbs will be
damaged if touched by hand or
contaminated with oil or grease. It is
important to use clean gloves or cloth
when handling a bulb which is to be
used again. A contaminated bulb may
be cleaned with methylated spirit
before refitting.
Open the hood and remove the top cover
as shown on page 6 - 14.
Pull the retaining clip (arrowed in A
above) upwards. Move the top of
headlight assembly outer bulb cover
rearwards to gain a ccess to the bulbs. Pull off the bulb connector. Release the
bulb spring clip (
B) from below the bulb
and lift it clear of the bulb. Pull out the
bulb from the headlight assembly.
Locate the new bulb (type H7) into the
headlight with the bulb tab
uppermost ( C). The bulb will only fit
correctly in one position.
Engage the spring clip ( B) to secure the
bulb. Fit the bulb connector.
Refit the bulb cover to the headlight
assembly and secure with the retaining
clip.
Refit the top cover and close the hood.
It is advisable to have the headlight aim
checked by a Retailer after bulb renewal. Front direction indicator bulb
The front direction indicator bulb is
located above the outer headlight bulb
(halogen or HID type) and is accessed via
the outer bulb cove
r (see column 1).
Turn the bulb holder a quarter turn anti-
clockwise and pull out ( D).
Remove the bulb and fit a new one of the
correct type, PY21W.
Fit the bulb holder to the lamp unit,
it will only fit in one position.
Turn clockwise to secure. Refit the
headlight assembly ou ter bulb cover and
secure with the retaining clip.
Refit the top cover and close the hood.