paint JAGUAR XJ 2004 X350 / 3.G Owners Manual

Owner Information 1 - 5
If you believe that your vehicle has a
defect which could cause a crash or could
cause injury or death, you should inform
the National Highway Traffic Safety
Administration (NHTSA) (USA only) in
addition to notifying Jaguar Cars.
If NHTSA receives similar complaints,
it may open an investigation, and if it
finds that a safety defect exists in a group
of vehicles, it may order a recall and
remedy campaign. However, NHTSA
cannot become involved in individual
problems between you, your Retailer,
or Jaguar Cars.
To contact NHTSA, you may either call
the Auto Safety Hotline toll-free at
1–800–424–9393 (or 366–0123 in
Washington, D.C. area) or write to:
NHTSA, U.S. Department of
Transportation, Washington, D.C. 20590.
To contact Jaguar Cars call 1–800 4
Jaguar.
You can also obtain other information
about motor safety from the Hotline.Vehicle Identification
Vehicle identification number (VIN)
It is essential that the Vehicle
Identification Number (VIN) is quoted in
all correspondence an d when ordering
replacement parts.
The number is visible from outside the
vehicle, on a plate in the lower left edge
of the windscreen.
Certification Label
Vehicles have the Certification Label
adhered to the left-hand front door hinge
post. Vehicle weights, paint code,
manufacture date and the VIN are shown
on this plate.

On the Road 4 - 35
Park Distance Control
Caution: It remains the driver’s
responsibility to detect obstacles and
estimate the car’s distance from
them. Some overhanging objects,
barriers, thin obstructions or painted
surfaces which could possibly cause
damage to the vehicle may not be
detected by the system. Always be
vigilant when reversing.
Park distance control is always
automatically switched on when the
ignition is turned on.
Caution:
1. If, for example, you are driving into a confined space such as a
home garage, the outer sensors
will detect the side walls and after
3 seconds will switch the tone off.
However, as movement
continues, the inner sensors will
eventually detect the rear wall
and will start the tone again.
2. The sensors are not active when the gear selector is in neutral,
therefore, take care if moving the
vehicle as the tone will not be
heard.
3. Do not clean the sensors with abrasive or sharp objects. Note:
1. For reliable operation, the sensors in
the front (if fitted) and rear bumpers
should be kept free from frost, ice and
grime.
2. When using a high pressure spray the sensors should only be sprayed briefly
and at least 8 inches (20 cm) distance
from the sensors.
3. The front parking aid may sound spurious tones if it detects a frequency
tone using the same band as the
sensors.
Rear Park Distance Control
When reverse gear is selected and
ignition is on, rear park distance control
automatically provides an audible
proximity warning (to the nearest
detected obstacle) when reversing the
vehicle if obstacles are detected within
the operating range, shown in the
illustration above (between
approximately 24 inches [60 cm] ( A) and
63 inches [160 cm] ( B).

On the Road 4 - 67
Fuels containing alcohol
Caution: Take care not to spill fuel
during refuelling. Fuel containing
alcohol can cause paint damage,
which may not be covered under the
warranty.
Some fuel suppliers sell fuel containing
alcohol without advertising its presence.
Where uncertainty exists check with the
service station operator.
Note: Some difficulty in starting may be
encountered when using alcohol blended
fuel.
Ethanol
Fuels containing up to 10 per cent
ethanol (grain alcohol) may be used.
Ensure the fuel has octane ratings no
lower than those recommended for
unleaded fuel. Most drivers will not
notice any operating difference with fuel
containing ethanol. If a difference is
detected, the use of conventional
unleaded fuel should be resumed. Methanol
Some fuels contain methanol (methyl or
wood alcohol). If you use fuels containing
methanol the fuels must also contain
co-solvents and corrosion inhibitors for
methanol. Also, do not use fuels that
contain more than three per cent
methanol even if they
contain co-solvents
and corrosion inhibitors. Fuel system
damage or vehicle performance problems
resulting from the use of such fuels is not
the responsibility of Jaguar Cars Limited,
and may not be covered under the
warranty.
Methyl Tertiary Butyl Ether (MTBE)
Unleaded fuel containing an oxygenate
known as MTBE can be used provided the
ratio of MTBE to conventional fuel does
not exceed 15 per cent.
MTBE is an ether based compound,
derived from petroleum, which has been
specified by several refiners as the
substance to enhance the octane rating of
fuel.

4-68 On the Road
Catalytic Converters
A few precautions on the use of vehicles
fitted with catalytic converters are
necessary. These are:
1. In order to maintain the efficiency of the emission control system it is
essential that unleaded fuel is used.
Use of leaded fuel will seriously
damage the catalytic converters.
2. Heavy impact on the converter casings must be avoided.
3. The engine settings must not be altered; they have been established to
ensure that the vehicle will comply
with stringent exhaust emission
regulations. Incorrect engine settings
could cause unusually high catalytic
converter temperatures and thus
result in damage to the converter and
vehicle. If adjustment to the settings is
considered necessary, this should be
performed by a Jaguar Retailer. 4. A correctly tuned engine optimises
exhaust emissions, performance and
fuel economy and it is recommended
that the vehicle is regularly
maintained.
5. Do not continue to operate the vehicle if any engine malfunction is evident;
malfunctions should be rectified
immediately. For instance, misfire,
loss of engine performance, excessive
oil consumption or engine run-on may
lead to unusually high catalytic
converter temperatures and may
result in damage to the converters and
vehicle.
6. The use of catalytic converters increases exhaust system
temperatures, therefore, do not
operate or park the vehicle in areas
where combustible materials such as
dry grass or leaves may come into
contact with the exhaust system. 7. Do not run the engine with either a
spark plug lead disconnected or a
spark plug removed. Do not use any
device that requires an insert into a
spark plug hole in order to generate air
pressure e.g. tyre pump, paint spray
attachment etc., as this could also
result in catalyti c converter damage.
8. The vehicle is designed for normal road use. Below are examples of abuse
which could damage the catalytic
converters and vehicle. These may
lead to a dangerous condition due to
excessively high catalytic converter
temperatures.
• Competition or off-road use.
• Excessive engine speed.
• Overloading the vehicle.
• Switching off the engine whilst in gear.

Maintenance 7 - 9
Check Brake Fluid Reservoir
Refer to page 7 - 5 for brake fluid reservoir
location. The brake fluid reservoir is
concealed by a lift-out cover.
To remove the lift-out cover, pull the two
clips on the rear edge of the cover
towards the front of the car, and lift the
cover out.
Caution:
1. While handling brake fluid, take extreme care; brake fluid must not
contact the vehicle paintwork.
2. Always use fresh, clean fluid from a new container. Never introduce
used brake fluid into the system. The fluid is visible through the
translucent casing of the reservoir and
must be maintained at the ‘MAX’ mark.
!WARNING:
The fluid level will drop as the brake
pads wear. If the le vel is very low
report the loss of fluid to the nearest
Jaguar Retailer. Do not drive the
vehicle until the cause is rectified.
If necessary, top up as follows:
Before removing the cap, clean the
reservoir and cap thoroughly with a non-
fluffy cloth to ensure that no foreign
matter enters the reservoir.
Unscrew the filler cap and top up to the
‘MAX’ level using brake fluid to
specification Jaguar Super DOT 4
(ESA-M6C25-A) .
Refit the filler cap securely.
To avoid contamination should any brake
fluid be spilt, replace the cap on the
reservoir before cleaning the spilt fluid
from the vehicle. Hydraulic fluid
The brake hydraulic fluid in the master
cylinder and brake operating system uses
non-mineral polyglycol based brake fluid
with a minimum standard of JAGUAR
SUPER DOT 4. ONLY FLUID OF THIS
TYPE AND STANDARD MAY BE USED.
!WARNING:
1. Contamination of the brake system fluid by as little as
1 per cent will cause rapid
deterioration of t he system seals.
Ensure that the brake fluid
reservoir cap is securely fitted.
2. Do not allow brake fluid to make contact with skin or eyes. If this
happens, rinse the affected area
immediately with plenty of water.
3. Brake fluid is toxic and flammable. Be sure to observe all warnings
indicated on the brake fluid
container.

7-10 Maintenance
Check Windscreen/Headlight
Washer Reservoir
Refer to page 7 - 5 for windscreen washer
reservoir location.
The washer reservoir contains the fluid
for the windscreen washers and the
headlight powerwash system (where
fitted).
Fill to just below th e neck with Jaguar
Windscreen Washer Fl uid diluted with
clean, preferably soft water as specified in
the instructions on the bottle.
Do not overfill.
Note: Using a non-approved fluid may
adversely affect the wiper blade rubber,
resulting in ineffectual and noisy wiping. Cold weather precautions
To prevent damage to the pump during
freezing conditions, use Jaguar
Windscreen Washer Fluid at the strength
shown on the bottle, for the anticipated
ambient temperature.
!WARNING:
1. Windscreen washer fluid is toxic and in concentrated form is
flammable. Be sure to observe all
warnings indicated on the washer
solution container.
Under no circumstances must
cooling system anti-freeze be
used, since this will damage the
paintwork.
2. State or local regulations on volatile organic compounds may
restrict the use of methanol,
a common windscreen washer
anti-freeze additive. Washer fluids
containing non-methanol anti-
freeze agents should be used only
if they provide cold weather
protection without damaging the
vehicle’s paint finish, wiper blades
or washer system.

Maintenance 7 - 11
Check Coolant Level
Refer to page 7 - 5 for coolant header tank
location.
The coolant level MAX and MIN
indicators are located inside the reservoir
and are only visible when looking into the
filler neck with the cap removed. Check
the level only when the engine is cold.
The coolant level shou ld be between the
MAX and MIN indicators. If persistent
coolant loss is noticed, have a Jaguar
Retailer investigate the cause
immediately.
!WARNING:
Do not remove the coolant header
tank filler/pressure cap while the
engine is hot. If the cap must be
removed, protect the hands against
escaping steam and slowly turn the
cap anti-clockwise until the steam
starts to escape. Leave the cap in this
position until the pressure is
released, and then remove the cap.
Topping up
!WARNING:
Do not allow anti-freeze to make
contact with skin or eyes. If this
happens, rinse the affected area
immediately with plenty of water.
Caution: Anti-freeze will damage
paintwork. Avoid spillage.
Top up with a mixture of 50% water and
50% anti-freeze until the coolant is
between the MAX and MIN indicators
inside the header tank. Use anti-freeze to
specification WSS M97B44, coloured
orange, Extended Life Coolant.
Refit the filler cap and hand-tighten
securely until the ratchet operates. Engine anti-freeze
When used at the correct concentration,
anti-freeze not only protects the engine
from frost damage in winter, it also
provides all year round protection against
internal corrosion.
The cooling system should always be
topped up or refilled with the specified
anti-freeze at the correct concentration.
This 50/50% mixture gives frost
protection for temperatures down to
–40°F (–40°C).
Do not mix any other anti-freeze with
that specified; inferior quality anti-freeze
may be ineffective in maintaining
adequate frost and corrosion protection
to the cooling system.
The coolant solution
may remain in the
cooling system for five years or
156,000 miles (250,000 km) after which
the system should be drained, flushed
and refilled.
Engine block heater
For further information consult your
Jaguar Retailer.
Caution: The fitting of an engine
block heater does not eliminate the
need for anti-freeze under freezing
conditions.

Maintenance 7 - 13
Battery
A low maintenance battery specifically
designed for use with this vehicle is fitted
below the luggage compartment floor.
!WARNING:
California Proposition 65:
Battery posts, terminals and related
accessories, contain lead and lead
compounds. Wash hands after
handling.
!WARNING:
1. The cell plugs and vent pipe must
be in place at all times when the
battery is in the vehicle. Failure to
fit, or incorrect fitting of these
items is potentially hazardous.
2. To avoid injury do not use an open flame or cause an electric spark
when checking the battery.
Hydrogen gas generated by the
battery is flammable and may
explode. 3. Do not connect any 12 volt
equipment (for example a 12 volt
lead lamp) directly to the battery
terminals. Use the accessory
sockets to temporarily connect
Jaguar approved accessories.
4. Do not let battery acid electrolyte come into contact with skin or
eyes. If you get any in your eyes or
on your skin, immediately rinse
with cold water and consult a
doctor.
Caution:
1. Switch off the ignition before disconnecting battery terminals.
Always disconnect the earth
terminal first and reconnect last.
2. Do not let battery acid come into contact with painted surfaces or
fabric.
The exterior of the battery should be
occasionally wiped clean to remove any
dirt or grease.
If a new battery is to be fitted, it must be
the same type as the original.
The use of unapproved batteries is not
recommended and coul d invalidate the
vehicle warranty. Note:
The service life of the battery is
dependent on its condition of charge.
It must always be sufficiently charged for
the battery to last an optimum length of
time.
We recommend that the battery charge is
checked frequently if the vehicle is used
mostly for short distance trips, or if it is
not used for long periods of time.
Battery/ignition isolator switches
Non-approved battery isolator switches,
which disconnect the power supply to all
electrical circuits, are not recommended.
Generator
To prevent damage to the generator,
do not run the engine while the battery
or any of the charging circuit cables are
disconnected.
The generator has polarity-sensitive
components that may be irreparably
damaged if subjected to incorrect
polarity. Ensure that the battery earth
lead is always connected to the battery
negative terminal.

Maintenance 7 - 23
Exterior Care
Note:All the cleaning materials
mentioned in this section are available
from the Jaguar Accessory Range.
Washing
For best results, do not wash the vehicle
under strong sunlight. Always allow the
vehicle to cool down before washing.
Do not use a dry cloth to wipe dirty
paintwork. Dust and gr itty substances are
abrasive and will scratch the paintwork.
Remove dirt using a cellulose sponge and
plenty of warm (never hot) water.
Rinse off with clean water and dry using a
clean, damp chamois leather.
Do not use household soaps or
detergents. The use of Jaguar Vehicle
Shampoo is recommended.
Do not direct hoses at full force around
door and luggage compartment seals.
Using high pressure water jets on the
paintwork is not recommended.
Do not allow bird droppings or tree sap
to harden. Remove from paintwork
immediately with a lukewarm soap and
water solution. In winter, when salt is used on the roads,
wash the vehicle frequently, and
immediately after encountering such
conditions. Clean undersides and wheel
arches using a high pressure jet.
Automatic car wash
Note:
Regular use of automatic car
washes tends to dull the lustre of the
paintwork.
After leaving the car wash, switch on the
windscreen wipers immediately to
remove water and prev ent a build up of
wax. Jaguar Screen Clean Paste can be
used to clean any residual wax from the
glass.
Caution: Ensure the rain sensitive
windscreen wipers are switched OFF
before entering an automatic car
wash, to prevent damage to the wiper
blades/arms.
Removing grease or tar
Remove grease or tar with Jaguar Tar
Remover or methylated spirit (alcohol).
White spirit is also effective, but must not
be applied to rubber, particularly the
windscreen wiper blades. Glass surfaces
To avoid scratching glass surfaces, do not
clean dirty glass with
dry paper or cloth.
Use clean, warm water and a chamois
leather which is reserved for glass only.
The following products will ensure glass
surfaces and windscreen wipers are kept
in good condition:
Jaguar Screen Clean Paste – Apply to the
exterior of the windscreen only to ensure
effective operation of the windscreen
wipers.
Jaguar Glass Cleaner – Interior and
exterior of all other glass surfaces.
Jaguar Screen Wash – Washer reservoir
additive.
Jaguar Winter Care Kit comprising
de-icer, ice scraper, anti-mist wipe cloth
and aerial cleaner – for use in adverse
weather conditions.
Note:
1. Renew the wiper blades when worn to prevent scratching. Clean the rubber
wiper blades regularly with a mild
detergent solution.
2. It is advisable to clean the windscreen with Jaguar Screen Clean Paste at
regular intervals.

7-24 Maintenance
Cleaning the rear screen
To avoid damaging the heating and radio
elements when cleaning the inside of the
rear screen use only a soft damp cloth or
chamois leather. Do not use solvents or
sharp objects to clean the glass.
Polishing paintwork and brightwork
For maximum protection against road
dust, salts, industrial fall-out etc., it is
recommended that the vehicle is polished
regularly using Jaguar Polish and a
Polishing Cloth.
Note:The vehicle’s brightwork should be
cleaned in the same way as the paintwork:
Chrome polish or other abrasive cleaners
must not be used. Paint chips
Scratches and chips should be touched in
before weathering action begins. Inspect
the paintwork imme
diately after the
vehicle has been washed.
Underhood cleaning
Underhood cleaning using high pressure
hoses or steam cleaners should be done
by a Jaguar Retailer. Indiscriminate use of
cleaning equipment could damage or
contaminate the electronic control
modules and fuse boxes.Care of Alloy Road Wheels
The alloy road wheels are covered with a
protective anti-corrosion coating.
To prevent corrosion it is essential that
this coating is not damaged.
When removing or fitting tyres always
advise the tyre fitte r to treat the alloy
wheels with great care and to only use
equipment with spigot or stud hole
clamping. The equipment must not have
any moving parts which contact the
wheel, and tyre levers must not be used.
Wash the wheels with soap and water at
two week intervals to avoid an
accumulation of particles which could
become embedded in the wheel surface.
In salty conditions the wheels should be
cleaned weekly.