warning JEEP CHEROKEE 1988 Service Owner's Manual

WARNING: DO NOT USE starting fluids (ether) or flammable liquids to
aid the starting of a Cummins Turbo-Diesel. NEVER pour diesel
fuel, flammable liquids or starting fluids into the air
cleaner canister, air intake or turbocharger housing in an
attempt to start the vehicle. A flash fire may result causing
personal injury.
TRANSFER CASE
CAUTION: Both drive axles are disengaged when transmission gear is
in Neutral position. Always set parking brake when leaving
vehicle unattended.
CAUTION: Never attempt to engage Low range when vehicle is moving
faster than 2-3 MPH (3-5 KM/H). Transfer case damage may
result.
GASOLINES CONTAINING ALCOHOL
CAUTION: Exclusive use of gasohol is not recommended. Vehicle test
results have shown that significant fuel system corrosion
can result when gasohol is used exclusively. Fuel additives
which are now being sold as octane enhancers are not
recommended. Most of these products contain high
concentrations of methanol.
WARRANTY INFORMATION
CAUTION: Due to the different warranties offered in various regions
and the variety of after-market extended warranties
available, please refer to the warranty package that came
with the vehicle to verify all warranty options.
BASIC NEW CAR WARRANTY
Jeep Corporation warrants to the original purchaser that the
vehicle is free from defects under normal use and service for 12
months or 12,000 miles, whichever comes first.
POWERTRAIN PROTECTION LIMITED WARRANTY
Begins at 12 months or 12,000 miles and lasts for 7 years or
70,000 miles, whichever comes first. Warranty covers Engine,
Transmission, Transfer Case, and Drive Shaft/Drive Axle(s) for RWD &
4WD.
Items not covered include, normal scheduled maintenance,
tune-ups, clutch adjustments, lack of proper maintenance, and vehicles
on which the mileage cannot readily be determined. A 100.00 deductible
on 2WD models and a 150.00 deductible on 4WD models applies to each
repair visit.
Powertrain Warranty also covers cost of towing to nearest
Jeep Dealer if vehicle cannot be driven due to failure of a covered
powertrain part.
ANTI-CORROSION PERFORATION WARRANTY
Warrants the sheet metal parts of the vehicle against
perforation (rust-through) due to corrosion. It covers any body sheet
metal panel for unlimited mileage during the first 36 months. Outer-
body sheet metal panels are covered for 7 years or 100,000 miles,

1 - 25 Amp
Rear Washer/Wiper
2 - 15 Amp
Radio, Cigarette Lighter
3 - 25 Amp
Blower Motor
4 - 20 Amp
Turn Signal, Back-Up Lights, Rear Window Defogger Relay
5 - 10 Amp
Dome Light, Courtesy Lights, Glove Box Light, Cargo Light,
Radio Memory, Power Mirrors, Teltak Connector
6 - 15 Amp
Hazard Warning System, Stoplights
7 - 10 Amp
Parking Lights, Headlight Warning Chime/Buzzer, Instrument
Panel Light Dimmer
8 - 7.5 Amp
Gauges, Instrument Cluster, Seat Belt Warning,
Headlight Delay, Chime Module, Overhead Console
9 - 5 Amp
Instrument Panel Illumination
10 - 25 Amp
Rear Window Defogger
11 - 30 Amp (Circuit Breaker)
Power Door Locks, Power Seats, Trailer Towing Wiring Harness
12 - 10 Amp
ETR Radio, Power Antenna
13 - Not Used (1984-87)
7.5 Amp (1988)
Transmission Control Unit
14 - 25 Amp
Headlight Delay, Horns, Security Alarm
15 - 5.5 Amp (Circuit Breaker)
Front Wiper
16 - 30 Amp (Circuit Breaker)
Power Windows
17 - 10 Amp
Clock, Security Alarm (IGN)

IMPORTANT: A quantity of parts will be distributed initially and
billed to all involved dealers. This quantity will cover a
portion of the total vehicles involved. Additional parts
will ba supplied as indicated in the Special Parts Supply
Message with this notification letter.
Each involved dealer, to whom vehicles in the recall were invoiced
(or the current dealer at the same street address), will receive
enough Oxygen Sensor Packages, Recall P/N C3905610, to service 25% of
those vehicles (minimum of 5 and maximum of 20 packages).
Each uninvolved dealer will receive 5 parts packages to service
vehicles upon request.
Each parts package contains the following components:
PARTS INFORMATION
PARTS INFORMATION TABLE







\









\








\
 
Description  Qty. 










\









\

\b







Oxygen Sensor  1 










\









\

\b







Instruction Sheet  1 











\









\







\f
OWNER NOTIFICATION & SERVICE SCHEDULING
All involved vehicle owners known to Chrysler are being notified of
the service requirement by first class mail. They are requested to
schedule appointments for the service with their dealers at the
earliest possible date. A copy of the
CUSTOMER NOTIFICATION LETTER is
in this bulletin.
Enclosed with each owner notification is an Owner Notification Form.
The involved vehicle and recall are identified on the form for owner
or dealer reference as needed.
SERVICE PROCEDURE
A. OXYGEN SENSOR INSPECTION
1. Raise Vehicle on a hoist and locate oxygen sensor in exhaust
manifold as shown in Fig. 1.
a. If the oxygen sensor has a metal stone shield around the sensor
body continue with Step B.
b. If the sensor does not have a stone shield, a new sensor has
already been installed and no further service is required.
WARNING: Exhaust manifold becomes very hot during engine operation.
Allow engine to cool before removing oxygen sensor.
1. Disconnect the oxygen sensor electrical connector.
2. Remove oxygen sensor using a crowfoot socket.
3. Clean exhaust manifold threads.

\003
SC HED ULE D S ER VIC ES - G ASO LIN E

1988 J e ep C hero ke e
1984-88 MAINTENANCE
AMC/Jeep Maintenance & Service Intervals - Gasoline
Jeep; Cherokee, Wagoneer
* PLEASE READ THIS FIRST *
NOTE: All SERVICE SCHEDULES are listed for normal service
vehicles. If vehicle is operated under severe service
conditions, see SEVERE SERVICE REQUIREMENTS (PERFORM
W/SERVICE SCHEDULES) for items requiring additional
maintenance.
NOTE: This article contains scheduled maintenance service
information. Fluid types and capacities listed with each
service in this article are only those necessary to perform
that scheduled service. For specifications pertaining to
fluid capacities for the entire vehicle, fuse and circuit
breaker identification, wheel and tire size, battery type,
warranty information, or model identification refer to the
MAINTENANCE INFORMATION article in this section.
CAUTIONS & WARNINGS
AIR CONDITIONING MAINTENANCE
WARNING: NEVER add A/C refrigerant to correct a non-cooling problem
unless pressure gauges are connected to the system by a
certified technician. Lack of cooling may be caused by a
restriction, therefore adding refrigerant can cause a
dangerous pressure rise.
ANTI-LOCK BRAKE SYSTEM (If Equipped)
The anti-lock brake system contains electronic equipment that
can be susceptible to interference caused by improperly installed or
high output radio transmitting equipment. Since this interference
could cause the possible loss of the anti-lock braking capability,
such equipment should be installed by qualified professionals.
On models equipped with anti-lock brake systems, ALWAYS
observe the following cautions:
* DO NOT attempt to bleed hydraulic system without first
referring to the appropriate ANTI-LOCK BRAKE SYSTEM article
in the BRAKES Section.
* DO NOT mix tire sizes. As long as tires remain close to the
original diameter, increasing the width is acceptable.
Rolling diameter must be identical for all 4 tires. Some
manufacturers recommend tires of the same brand, style and
type. Failure to follow this precaution may cause inaccurate
wheel speed readings.
* Use ONLY recommended brake fluids. DO NOT use silicone brake
fluids in an ABS-equipped vehicle.
BATTERY WARNING
WARNING: When battery is disconnected, vehicles equipped with

computers may lose memory data. When battery power is
restored, driveability problems may exist on some vehicles.
These vehicles may require a relearn procedure. See COMPUTER
RELEARN PROCEDURES article in GENERAL INFORMATION section.
REPLACING BLOWN FUSES
Before replacing a blown fuse, remove ignition key, turn off
all lights and accessories to avoid damaging the electrical system. Be
sure to use fuse with the correct indicated amperage rating. The use
of an incorrect amperage rating fuse may result in a dangerous
electrical system overload.
BRAKE PAD WEAR INDICATOR
Indicator will cause a squealing or scraping noise, warning
that brake pads need replacement.
BRAKE WARNING LIGHT
CAUTION: If BRAKE warning light is on with parking brake disengaged
and engine running, there may be a problem in the hydraulic
brake system. Braking effort, brake pedal travel and
stopping distances may increase.
CATALYTIC CONVERTER
To prevent catalytic converter overheating, DO NOT allow
engine to idle for more than 20 minutes.
COMMAND-TRAC (4WD)
CAUTION: NEVER operate a Command-Trac vehicle in 4WD on dry,
hard-surfaced roads for a sustained period. Use 4L only
when needed for added pulling power. Operating vehicle in
4WD mode on such roads will cause stress and possible
damage to components, as well as make shifting difficult.
To reduce shifting effort, drive vehicle in Reverse for a
few feet, or drive off hard-surfaced road momentarily to
allow tire slippage.
FRONT AND REAR DIFFERENTIALS (4WD)
CAUTION: DO NOT use water, steam, kerosene or gasoline for flushing
a differential. ONLY use a flushing oil.
TRAC-LOK DIFFERENTIALS (4WD)
CAUTION: DO NOT flush a rear axle Trac-Lok differential. Trac-Lok
differentials may be cleaned only by disassembling the
unit and wiping the components with clean, lint-free cloth.
CAUTION: NEVER attempt to engage Low range when vehicle is moving
faster than 2-3 MPH, as transfer case damage may result.
GASOLINE CONTAINING ALCOHOL
CAUTION: Exclusive use of gasohol is not recommended. Vehicle test
results have shown that significant fuel system corrosion
can result when gasohol is used exclusively.

HALOGEN BULBS
Halogen bulbs contain pressurized gas which may explode if
overheated. DO NOT touch glass portion of bulb with bare hands. Eye
protection should be worn when handling or working around halogen
bulbs.
OIL FILTER
CAUTION: The engine oil filter mount has metric threads. Use of a
filter with improper threads can result in oil leakage and
possible engine damage. Look for M20 x 1.5 symbol on the
filter.
RADIATOR CAP
CAUTION: Always disconnect the fan motor when working near the
radiator fan. The fan is temperature controlled and could
start at any time even when the ignition key is in the OFF
position. DO NOT loosen or remove radiator cap when cooling
system is hot.
RADIATOR FAN
Keep hands away from radiator fan. Fan is controlled by a
thermostatic switch which may come on or run for up to 15 minutes even
after engine is turned off.
WHEEL & TIRE WARNINGS
CAUTION: Replacing original tires with different size tires may
result in false speedometer and odometer indications. Check
with dealer before using different size tires on vehicle.
CAUTION: Ensure all 4 wheels on vehicle have same tire size, type
and circumference in order to provide proper vehicle
handling. DO NOT mix radial-ply with bias-ply or
bias-belted tires. On 4WD vehicles, if tire size, type and
circumference on all 4 wheels are not the same, gear
shifting will be adversely affected and can damage transfer
case.
CAUTION: Temporary-use spare tires are for emergency use only. DO
NOT drive vehicle faster than 50 MPH or more than 100 miles
when using spare tire. DO NOT operate vehicle in 4WD mode
when using spare tire, as damage to transfer case can
result. Temporary-use spare tires have a total tread life
of 3,000 miles.
SERVICE POINT LOCATIONS

SER VIC E IN DIC ATO R & W AR NIN G L IG HTS

1988 J e ep C hero ke e
1984-92 MAINTENANCE
AMC/Jeep/Eagle Service Indicator & Warning Lights
Jeep; Cherokee, Wagoneer
SERVICE INDICATOR & WARNING LIGHTS
BRAKE WARNING LIGHT
If the light stays on when the parking brake is off, it
indicates a possible brake system fluid leak or low pressure level.
LOCK INDICATOR LIGHT (1984-87)
Indicates that Selec-Trac transfer case is in part time 4WD
(high or low range).
FULL TIME 4WD INDICATOR LIGHT
Indicates that Selec-Trac transfer case is in full-time 4WD
(4x4 FULL TIME).
PART TIME 4WD INDICATOR LIGHT
Indicates that Selec-Trac transfer case is in part time 4WD
(4x4 PART TIME or 4 LO) or that Command-Trac transfer case is in 4WD
(4H or 4L).
WATER IN FUEL LIGHT (TURBO DIESEL)
Indicates water has collected in the fuel filter and should
be drained immediately.
DIESEL WAIT LIGHT (TURBO DIESEL)
Illuminates during glow plugs warm-up cycle.
LOW FUEL WARNING LIGHT
Glows when approximately 2 gals. (7.6L) remain in fuel tank.
EMISSION MAINTENANCE INDICATOR LIGHT
Illuminates at approximately 82,500 miles to indicate
scheduled maintenance (or recommended maintenance on California
vehicles). Light will remain on until system is serviced and light is
reset.
CHECK ENGINE LIGHT
If this light illuminates and remains on while driving, it
indicates a potential engine control problem that needs service.
CHECK ANTI-LOCK LIGHT
Illuminates to indicate a self-check is in process at vehicle
start up. If light remains on after start-up or comes on and stays on

at road speeds, it may indicate that the ABS system has detected a
malfunction or has become inoperative. The system reverts to standard
non-anit-lock brakes. If both Red BRAKE light and Amber CHECK ANTI-
LOCK light are on, have vehicle serviced immediately.
Fig. 1: Instrument Panel Interior Controls
Courtesy of Chrysler Motors.
Fig. 2: Dash Gauges & Warning Lights (Gasoline Engines)
Courtesy of Chrysler Motors.

Fig. 3: Dash Gauges & Warning Lights (Turbo-Diesel Engines)
Courtesy of Chrysler Motors.

STE ER IN G C O LU M N S W IT C HES

1988 J e ep C hero ke e
1988 STEERING
Jeep Steering Column Switches
All Models
REMOVAL & INSTALLATION
TURN SIGNAL & HAZARD FLASHER SWITCHES
Removal & Installation
1) Place front wheels in straight-ahead position. Disconnect
battery negative cable. Remove the steering wheel. Refer to the
STEERING WHEEL & HORN REMOVAL article.
2) On models with A/T, place selector lever in "PARK"
position. Remove selector lever retaining pin and lever. Using 2
screwdrivers, remove lock plate cover. On models with tilt column,
remove tilt lever.
3) Using Plate Compressor (J-23653-A), compress lock plate.
If shaft has metric threads, use Metric Forcing Screw (J-23653-4)
prior to installing compressor on shaft. Remove and discard lock plate
snap ring. Remove plate compressor
NOTE: The lock plate is under strong spring tension. DO NOT
attempt to remove snap ring without using lock plate
compressor.
4) Remove lock plate, canceling cam, upper bearing preload
spring, spring seat and bearing race (thrust washer on some models).
Depress hazard warning switch while unscrewing from column.
5) On vehicles with A/T, use a paper clip to compress lock
tab retaining shift quadrant light wire in connector block. Disconnect
wire. On all models, remove turn signal lever attaching screw and
lever.
6) On vehicles with cruise control, disconnect 2 of 4 wires
at switch connector. Fold wires back along harness. Tape wires to
harness. Tape a string to harness to aid in removal.
7) Disconnect turn signal switch wire harness at bottom of
steering column. Tape around turn signal switch harness connector to
aid in removal. Remove turn signal switch attaching screws. Remove
switch. To install, reverse removal procedure.
LOCK CYLINDER
Removal
1) Remove horn button and steering wheel. Refer to the
STEERING WHEEL & HORN REMOVAL article. Remove turn signal switch.
Remove key warning buzzer switch and contacts as an assembly, using
needle-nose pliers.
2) On models with standard column, turn ignition lock
cylinder (clockwise) 2 detent positions beyond the "OFF/LOCK"
position. On models with tilt column, turn lock cylinder to "LOCK"
position. On all models, compress lock cylinder retaining tab and
remove lock cylinder from housing. See Fig. 1.