garage door opener JEEP CHEROKEE 2016 KL / 5.G Owners Manual

PARKVIEW REAR BACK UP CAMERA — IF
EQUIPPED .......................... .280
 GARAGE DOOR OPENER — IF EQUIPPED . . .282
▫ Before You Begin Programming HomeLink . . .283
▫ Programming A Rolling Code .............284
▫ Programming A Non-Rolling Code .........286
▫ Canadian/Gate Operator Programming ......287
▫ Using HomeLink .....................289
▫ Security ........................... .289
▫ Troubleshooting Tips ...................289
▫ General Information ....................290
 POWER SUNROOF WITH POWER SHADE — IF
EQUIPPED .......................... .291
▫ Opening Sunroof — Express ..............293▫
Opening Sunroof — Manual Mode .........293
▫ Closing Sunroof — Express ...............293
▫ Closing Sunroof — Manual Mode ..........294
▫ Venting Sunroof — Express ..............294
▫ Opening Power Shade — Express ..........294
▫ Opening Power Shade — Manual Mode .....294
▫ Closing Power Shade — Express ...........295
▫ Closing Power Shade — Manual Mode ......295
▫ Pinch Protect Feature ...................295
▫ Wind Buffeting ...................... .295
▫ Sunroof Maintenance ...................296
▫ Ignition OFF Operation .................296
 POWER OUTLETS .....................296
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

CAUTION!
•To avoid vehicle damage, ParkView should only be
used as a parking aid. The ParkView camera is
unable to view every obstacle or object in your
drive path.
• To avoid vehicle damage, the vehicle must be
driven slowly when using ParkView to be able to
stop in time when an obstacle is seen. It is recom-
mended that the driver look frequently over his/her
shoulder when using ParkView.
WARNING!
Drivers must be careful when backing up even when
using the ParkView Rear Back Up Camera. Always
check carefully behind your vehicle, and be sure to
(Continued)
WARNING! (Continued)
check for pedestrians, animals, other vehicles, ob-
structions, or blind spots before backing up. You are
responsible for the safety of your surroundings and
must continue to pay attention while backing up.
Failure to do so can result in serious injury or death.
NOTE: If snow, ice, mud, or any foreign substance builds
up on the camera lens, clean the lens, rinse with water,
and dry with a soft cloth. Do not cover the lens.
GARAGE DOOR OPENER — IF EQUIPPED
HomeLink replaces up to three remote controls (hand-
held transmitters) that operate devices such as garage
door openers, motorized gates, lighting or home security
systems. The HomeLink unit operates off your vehicle’s
battery.
282 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

NOTE:
•Erasing all channels should only be performed when
programming HomeLink for the first time. Do not
erase channels when programming additional buttons.
• If you have any problems, or require assistance, please
call toll-free 1-800-355-3515 or, on the Internet at
HomeLink.com for information or assistance.
Programming A Rolling Code
For programming garage door openers that were manu-
factured after 1995. These garage door openers can be
identified by the “LEARN” or “TRAIN” button located
where the hanging antenna is attached to the garage door
opener. It is NOT the button that is normally used to
open and close the door. The name and color of the
button may vary by manufacturer. 1. Place the ignition in the ON/RUN position.
Training The Garage Door Opener
1 — Door Opener
2 — Training Button
284 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

2. Place the hand-held transmitter 1 to 3 inches (3 to 8cm) away from the HomeLink button you wish to
program while keeping the HomeLink indicator light
in view.
3. Push and hold the HomeLink button you want to program while you push and hold the hand-held
transmitter button.
4. Continue to hold both buttons and observe the indi- cator light. The HomeLink indicator will flash slowly
and then rapidly after HomeLink has received the
frequency signal from the hand-held transmitter. Re-
lease both buttons after the indicator light changes
from slow to rapid.
5. At the garage door opener motor (in the garage), locate the “LEARN” or “TRAINING” button. This can
usually be found where the hanging antenna wire is
attached to the garage door opener/device motor. Firmly push and release the “LEARN” or “TRAIN-
ING” button. On some garage door openers/devices
there may be a light that blinks when the garage door
opener/device is in the LEARN/TRAIN mode.
NOTE: You have 30 seconds in which to initiate the next
step after the LEARN button has been pushed.
6. Return to the vehicle and push the programmed HomeLink button twice (holding the button for two
seconds each time). If the garage door opener/device
activates, programming is complete.
NOTE: If the garage door opener/device does not acti-
vate, push the button a third time (for two seconds) to
complete the training.
To program the remaining two HomeLink buttons, repeat
each step for each remaining button. DO NOT erase the
channels.
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 285

Reprogramming A Single HomeLink Button
(Rolling Code)
To reprogram a channel that has been previously trained,
follow these steps:
1. Cycle the ignition to the ON/RUN position.
2. Push and hold the desired HomeLink button until theindicator light begins to flash after 20 seconds. Do not
release the button.
3. Without releasing the button proceed with “Program-
ming A Rolling Code” step 2 and follow all remaining
steps.
Programming A Non-Rolling Code
For programming Garage Door Openers manufactured
before 1995.
1. Cycle the ignition to the ON/RUN position. 2. Place the hand-held transmitter 1 to 3 inches (3 to 8
cm) away from the HomeLink button you would like
to program while keeping the HomeLink indicator
light in view.
3. Push and hold the HomeLink button you want to program while you push and hold the hand-held
transmitter button.
4. Continue to hold both buttons and observe the indi- cator light. HomeLink indicator will flash slowly and
then rapidly after HomeLink has received the fre-
quency signal from the hand-held transmitter. Release
both buttons after the indicator light changes from
slow to rapid.
5. Push and hold the programmed HomeLink button and observe the indicator light.
• If the indicator light stays on constantly, program-
ming is complete and the garage door/device should
activate when the HomeLink button is pressed.
286 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

2. Place the hand-held transmitter 1 to 3 inches (3 to 8cm) away from the HomeLink button you wish to
program while keeping the HomeLink indicator light
in view.
3. Continue to push and hold the HomeLink button, while you press and release (“cycle”) your hand-held
transmitter every two seconds until HomeLink has
successfully accepted the frequency signal. The indi-
cator light will flash slowly and then rapidly when
fully trained.
4. Watch for the HomeLink indicator to change flash rates. When it changes, it is programmed. It may take
up to 30 seconds or longer in rare cases. The garage
door may open and close while you are programming.
5. Push and hold the programmed HomeLink button and observe the indicator light. NOTE:
•If the indicator light stays on constantly, program-
ming is complete and the garage door/device should
activate when the HomeLink button is pushed.
• To program the two remaining HomeLink buttons,
repeat each step for each remaining button. DO NOT
erase the channels.
If you unplugged the garage door opener/device for
programming, plug it back in at this time.
Reprogramming A Single HomeLink Button
(Canadian/Gate Operator)
To reprogram a channel that has been previously trained,
follow these steps:
1. Cycle the ignition to the ON/RUN position.
288 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

2. Push and hold the desired HomeLink button until theindicator light begins to flash after 20 seconds. Do not
release the button.
3. Without releasing the button proceed with
“Canadian/Gate Operator Programming” step 2 and
follow all remaining steps.
Using HomeLink
To operate, push and release the programmed HomeLink
button. Activation will now occur for the programmed
device (i.e. garage door opener, gate operator, security
system, entry door lock, home/office lighting, etc.) The
hand-held transmitter of the device may also be used at
any time.
Security
It is advised to erase all channels before you sell or turn
in your vehicle. To do this, push and hold the two outside buttons for 20
seconds until the red indicator flashes. Note that all
channels will be erased. Individual channels cannot be
erased.
The HomeLink Universal Transceiver is disabled when
the Vehicle Security Alarm is active.
Troubleshooting Tips
If you are having trouble programming HomeLink, here
are some of the most common solutions:
•
Replace the battery in the Garage Door Opener hand-
held transmitter.
• Push the LEARN button on the Garage Door Opener
to complete the training for a Rolling Code.
• Did you unplug the device for programming and
remember to plug it back in?
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 289

If you have any problems, or require assistance, please
call toll-free 1-800-355-3515 or, on the Internet at
HomeLink.com for information or assistance.
WARNING!
•Vehicle exhaust contains carbon monoxide, a dan-
gerous gas. Do not run your vehicle in the garage
while programming the transceiver. Exhaust gas
can cause serious injury or death.
• Your motorized door or gate will open and close
while you are programming the universal trans-
ceiver. Do not program the transceiver if people,
pets or other objects are in the path of the door or
gate. Only use this transceiver with a garage door
opener that has a “stop and reverse” feature as
required by Federal safety standards. This includes
most garage door opener models manufactured
(Continued)
WARNING! (Continued)
after 1982. Do not use a garage door opener without
these safety features. Call toll-free 1-800-355-3515
or, on the Internet at HomeLink.com for safety
information or assistance.
General Information
This device complies with FCC rules Part 15 and Industry
Canada RSS-210. Operation is subject to the following
two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference that may be
received including interference that may cause unde-
sired operation.
290 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Data Recorder, Event.......................90
Daytime Brightness, Interior Lights .............174
Daytime Running Lights ....................168
Dealer Service ........................... .664
Defroster, Rear Window .....................313
Defroster, Windshield ................116, 423, 424
Diagnostic System, Onboard .................661
Dimmer Switch, Headlight ...................171
Dipsticks Oil (Engine) .......................... .665
Disabled Vehicle Towing ....................652
Disposal Antifreeze (Engine Coolant) ................694
Door Ajar .......................... .336, 337
Door Ajar Light ...................... .336, 337
Door Locks Door Locks ............................34
KeyFob...............................34
Remote ...............................34 Remote Keyless Entry (RKE)
................34
Door Locks, Automatic ......................36
Door Opener, Garage ...................... .282
Driver Information Display DID................................ .373
Instrument Cluster Display ................373
Driver Information Display (DID) Instrument Cluster ..................... .372
Oil Change ........................... .372
Driver’s Seat Back Tilt ..................... .149
Driving ............................... .506
E-85 Fuel .............................. .581
Electrical Outlet, Auxiliary (Power Outlet) ........296
Electric Parking Brake ..................... .512
Electric Remote Mirrors .....................134
Electronic Brake Control System ...............520
Anti-Lock Brake System ..................520
Electronic Roll Mitigation .................532
750 INDEX

Fuel.................................. .577
Additives ............................ .579
Clean Air ............................ .577
Ethanol .......................... .578, 581
Filler Cap (Gas Cap) .....................584
Gasoline ............................. .577
Light ............................... .346
Materials Added ....................... .579
Methanol ............................ .578
Octane Rating ..................... .577, 726
Requirements ......................... .577
Specifications ......................... .726
Tank Capacity ......................... .725
Fuel, Flexible ........................... .581
Fuses ................................. .706
Garage Door Opener (HomeLink) ..........282, 289
Gas Cap (Fuel Filler Cap) ...................584
Gasoline, Clean Air ....................... .577Gasoline (Fuel)
.......................... .577
Gasoline, Reformulated .....................577
Gear Ranges ............................ .487
Gear Select Lever Override ..................651
Glass Cleaning .......................... .705
Gross Axle Weight Rating ...................592
Gross Vehicle Weight Rating ..................591
GVWR ................................ .589
Hazard Warning Flasher ....................617
Headlights Automatic ........................... .166
Bulb Replacement ...................... .720
Cleaning ............................ .704
Delay ............................... .167
High Beam/Low Beam Select Switch .........171
Lights On Reminder .....................169
On With Wipers ....................... .166
Passing ............................. .171
10
INDEX 753