bulb JEEP COMPASS 2008 1.G User Guide

Your vehicle has a simple ignition key actuated test,
which you can use prior to going to the test station. To
check if your vehicle's OBD system is ready, you must do
the following:
1. Insert your ignition key into the ignition switch.
2. Turn the ignition to the ON position, but do not crank
or start the engine.
3. If you crank or start the engine, you will have to start
this test over.
4. As soon as you turn your key to the ON position, you
will see your MIL symbol come on as part of a normal
bulb check.
5. Approximately 15 seconds later, one of two things will
happen:
a. The MIL will flash for about 10 seconds and then
return to being fully illuminated until you turn off theignition key or start the engine. This means that your
vehicle's OBD system isnot readyand you shouldnot
proceed to the I/M station.
b. The MIL will not flash at all and will remain fully
illuminated until you turn off the ignition key or start
the engine. This means that your vehicle's OBD system
isreadyand you can proceed to the I/M station.
If your OBD system isnot ready,you should see your
authorized dealer or repair facility. If your vehicle was
recently serviced or had a battery failure or replacement,
you may need to do nothing more than drive your
vehicle as you normally would in order for your OBD
system to update. A recheck with the above test routine
may then indicate that the system is now ready.
Regardless of whether your vehicle's OBD system is
ready or not ready, if the MIL symbol is illuminated
during normal vehicle operation, you should have your
MAINTAINING YOUR VEHICLE 315
7

VEHICLE STORAGE
If you will not be using your vehicle for more than 21
days you may want to take steps to preserve your battery.
You may:
²Disengage the mini fuse in the Power Distribution
Center labeled IOD (Ignition Off-Draw).
²Or, disconnect the negative cable from the battery.
REPLACEMENT BULBS
All the inside bulbs are brass or glass wedge base.
Aluminum base bulbs are not approved and should not
be used for replacement.
LIGHT BULBS Ð Interior Bulb Number
Front Header Lamp......................T578
Center Dome Lamp......................T578
Rear Cargo/Flashlight.................8±A35LFLIGHTS BULBS Ð Outside Bulb No.
Low Beam/High Beam Headlight............ H13
Front Park/Turn Signal/Side Marker
Light.......................3157AK or 3157A
Front Fog Light.........................9145
Center High Mounted Stop Light
(CHMSL)...................... LEDAssembly
Rear Tail/Stop..........................3157
Rear Turn Signal...............3757AK or 3757A
Backup Light.....................W16W (921)
License Light.......................... W5W
Off-Road Light........................... H3
350 MAINTAINING YOUR VEHICLE

BULB REPLACEMENT
Headlamps²Raise the hood and locate connector behind the head-
lamp.
Locating Headlamp ConnectorReleasing Red Lock Tab
MAINTAINING YOUR VEHICLE 351
7

²Reach into engine compartment and pull red lock out
at connector.
²Twist the bulb to the left and pull outward from
assembly.
NOTE:These are halogen bulbs. Take care not to touch
the bulb with your fingers. Body oils from your fingers
could cause excessive heat buildup which reduces bulb
life.
Remove green connector from back of bulb by pulling
straight back
Twisting Bulb From Socket
352 MAINTAINING YOUR VEHICLE

Fog Lights
1. Access lamp through the lower fascia cutout.
2. Rotate bulb and connector 1/4 turn counterclockwise.
3. Pull bulb off of connector.
Removing Halogen Bulb From Assembly
Fog Light and Connector
MAINTAINING YOUR VEHICLE 353
7

2. Grasp the tail lamp and pull firmly to disengage the
lamp from the aperture panel.3. Twist and remove socket from lamp.
Pulling Lamp From Body
Removing Socket and Bulb
MAINTAINING YOUR VEHICLE 355
7

4. Remove bulb from socket and replace.License Lights
1. Use a screw driver to gently pry against the side of the
snap tab to remove the lamp from the liftgate.
Removing Bulb From Socket
Prying Lamp from Liftgate
356 MAINTAINING YOUR VEHICLE

2. Rotate the socket 1/4 turn counterclockwise. 3. Pull bulb from socket.
Removing Socket from LampRemoving Bulb From Socket
MAINTAINING YOUR VEHICLE 357
7

2. Unlatch the wire clasp securing the bulb into the
housing and rotate it into the position shown.3. Disconnect the bulb from the lamp harness to replace
the bulb.
Releasing the bulbDisconnecting bulb
MAINTAINING YOUR VEHICLE 359
7

Ball Joints............................. 327
Battery............................... 324
Keyless Transmitter Replacement (RKE)....... 24
Belts, Drive............................ 320
Body Mechanism Lubrication............... 327
B-Pillar Location........................ 252
Brake Assist System...................... 128
Brake Control System, Electronic............. 127
Brake Fluid............................ 362
Brake, Parking.......................... 241
Brake System........................243,335
Anti-Lock (ABS).................126,127,244
Hoses.............................. 336
Master Cylinder....................... 337
Parking............................. 241
Warning Light........................ 163
Brakes.............................243,335
Brake/Transmission Interlock............... 233
Break-In Recommendations, New Vehicle........ 65Bulb Replacement.....................350,351
Bulbs, Light............................ 350
Calibration, Compass..................... 180
Capacities, Antifreeze (Engine Coolant)........ 360
Capacities, Fluid........................ 360
Caps, Filler
Fuel................................ 279
Oil (Engine).......................312,319
Car Washes............................ 342
Carbon Monoxide Warning................. 278
Cargo Area Cover....................... 150
Cargo Area Features...................... 148
Cargo Compartment
Light............................... 148
Luggage Carrier....................... 154
Cargo Light............................ 148
Cargo Load Floor........................ 150
Cargo Tie-Downs........................ 151
INDEX 383
10