light JEEP GRAND CHEROKEE 2010 Owner handbook (in English)
[x] Cancel search | Manufacturer: JEEP, Model Year: 2010, Model line: GRAND CHEROKEE, Model: JEEP GRAND CHEROKEE 2010Pages: 350, PDF Size: 4.58 MB
Page 17 of 350
NOTE:
You can insert the double-sided emergency
key into the lock cylinders with either side
up.
Removing Key Fob From IgnitionPlace the shift lever in PARK. Turn the Key Fob
to the OFF position and then remove the Key
Fob.
With the Keyless Enter-N-Go feature, the EVIC
will display the ignition switch position “OFF/
ACC/RUN”. Refer to “Electronic Vehicle Infor-
mation Center (EVIC)” in “Understanding Your
Instrument Panel” for further information.NOTE:
•
If you try to remove the Key Fob before
you place the shift lever in PARK, it may
become trapped temporarily in the igni-
tion switch. If this occurs, rotate the key
to the right slightly, then remove the Key
Fob as described. If a malfunction occurs,
the system may trap the key in the igni-
tion switch to warn you that this safety
feature is inoperable. The engine can be
started and stopped, but the Key Fob
cannot be removed until you obtain ser-
vice.
• The power window switches, radio, power
sunroof (if equipped), and power outlets
will remain active for up to 10 minutes
after the ignition switch is turned to the
LOCK position. Opening either front door
will cancel this feature. The time for this
feature is programmable. Refer to “Elec-
tronic Vehicle Information Center (EVIC)/
Personal Settings (Customer-Program-
mable Features)” in “Understanding Your
Instrument Panel” for further information.
WARNING!
• Never leave children alone in a vehicle.
Leaving unattended children in a vehicle is
dangerous for a number of reasons. A child
or others could be seriously or fatally in-
jured. Do not leave the Key Fob in the
ignition or Keyless Enter-N-Go in the ACC
or ON/RUN mode. A child could operate
power windows, other controls, or move the
vehicle.
• Do not leave children or animals inside
parked vehicles in hot weather. Interior
heat build-up may cause serious injury or
death.
CAUTION!
An unlocked car is an invitation to thieves.
Always remove Key Fob from the ignition and
lock all doors when leaving the vehicle unat-
tended.
Emergency Key Removal
13
Page 18 of 350
Key-In-Ignition ReminderOpening the driver’s door when the Key Fob is
in the ignition and the ignition switch position is
OFF or ACC, sounds a signal to remind you to
remove the Key Fob.
NOTE:
The Key-In-Ignition reminder only sounds
when the Key Fob is placed in the OFF or
ACC ignition position.
With the Keyless Enter-N-Go feature, opening
the driver’s door when the vehicle’s ignition
switch is placed in ACC or ON/RUN (engine
stopped) will cause the reminder chime to
sound. Refer to “Starting Procedures” in “Start-
ing And Operating” for further information.
SENTRY KEYThe Sentry Key Immobilizer system prevents
unauthorized vehicle operation by disabling
the engine. The system does not need to be
armed or activated. Operation is automatic,
regardless of whether the vehicle is locked or
unlocked. The system uses the factory-mated Key Fob
with Remote Keyless Entry (RKE) transmitter
and Wireless Ignition Node (WIN) to prevent
unauthorized vehicle operation. Therefore, only
Key Fobs that are programmed to the vehicle
can be used to start and operate the vehicle.
The system will shut the engine off in two
seconds if an invalid Key Fob is used to start
the engine.
After turning the ignition switch to the ON/RUN
position, the Vehicle Security Light will turn on
for three seconds for a bulb check. If the light
remains on after the bulb check, it indicates
that there is a problem with the electronics. In
addition, if the light begins to flash after the
bulb check, it indicates that someone used an
invalid Key Fob to start the engine. Either of
these conditions will result in the engine being
shut off after two seconds.
If the Vehicle Security Light turns on during
normal vehicle operation (vehicle running for
longer than 10 seconds), it indicates that there
is a fault in the electronics. Should this occur,
have the vehicle serviced as soon as possible
by an authorized dealer.
CAUTION!
The Sentry Key
Immobilizer system is not
compatible with some after-market remote
starting systems. Use of these systems may
result in vehicle starting problems and loss of
security protection.
All of the Key Fobs provided with your new
vehicle have been programmed to the vehicle
electronics.
Replacement Keys
NOTE:
Only Key Fobs that are programmed to the
vehicle electronics can be used to start and
operate the vehicle. Once a Key Fob is
programmed to a vehicle, it cannot be pro-
grammed to any other vehicle.
CAUTION!
• Always remove the Key Fobs from the
vehicle and lock all doors when leaving the
vehicle unattended.
(Continued)
14
Page 19 of 350
CAUTION!(Continued)
• With Keyless Enter-N-Go, always remem-
ber to place the ignition in OFF.
At the time of purchase, the original owner is
provided with a four-digit Personal Identifica-
tion Number (PIN). Keep the PIN in a secure
location. This number is required for authorized
dealer replacement of Key Fobs. Duplication of
Key Fobs may be performed at an authorized
dealer.
NOTE:
When having the Sentry Key Immobilizer
system serviced, bring all vehicle ignition
keys with you to an authorized dealer.
Customer Key ProgrammingProgramming Key Fobs or RKE transmitters
may be performed at an authorized dealer.
General InformationThe Sentry Key operates on a carrier fre-
quency of 433.92 MHz. The Sentry Key Immo-
bilizer system will be used in the following
European countries, which apply Directive
1999/5/EC: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Hungary, Ireland, Italy, Luxembourg, Nether-
lands, Norway, Poland, Portugal, Romania,
Russian Federation, Slovenia, Spain, Sweden,
Switzerland, Yugoslavia, and United Kingdom.
Operation is subject to the following conditions:
•
This device may not cause harmful interfer-
ence.
• This device must accept any interference
that may be received, including interference
that may cause undesired operation.
VEHICLE SECURITY ALARM —
IF EQUIPPED
The Vehicle Security Alarm monitors the hood,
liftgate, liftgate flipper glass, vehicle doors for
unauthorized entry, and the ignition switch for
unauthorized operation. If something triggers
the alarm, the Vehicle Security Alarm will pre-
vent the vehicle from starting and provide the
following audio and visual signals: the horn will
pulse, the headlights will flash, the park lights
will flash, and the Vehicle Security Light in the
instrument cluster will flash.
To Arm the System
Vehicles Not Equipped with Keyless
Enter-N-Go
Remove the key from the ignition switch and
either press a power door lock switch while the
driver or passenger door is open, or press the
LOCK button on the Remote Keyless Entry
(RKE) transmitter. After the last door is closed,
or if all doors are closed, the Vehicle Security
Alarm will arm itself in about 16 seconds.
During that time, the Vehicle Security Light will
flash. If it does not illuminate, the Vehicle Secu-
rity Alarm is not arming. Also, if you open a door
during the arming period, the Vehicle Security
Alarm will cancel the arming process. If you
wish to rearm the Vehicle Security Alarm after
closing the door, you must repeat one of the
previously-described arming sequences.
Vehicles Equipped with Keyless
Enter-N-Go
Press the Keyless Enter-N-Go Start/Stop button
until the Electronic Vehicle Information Center
(EVIC) indicates that the vehicle ignition is
“OFF” (refer to “Starting Procedures” in “Start-
ing And Operating” for further information).
Then either press the power door LOCK switch
15
Page 20 of 350
while the driver or passenger door is open,
press the lock button on the front driver or
passenger door handle with a valid key fob in
range, or press the Remote Keyless Entry
(RKE) transmitter LOCK button (refer to “Pas-
sive Entry System” in “Things To Know Before
Starting Your Vehicle” for further information).
To Disarm the System
Vehicles Not Equipped with Keyless
Enter-N-Go
Either press the UNLOCK button on the RKE
transmitter, or insert a valid ignition key into the
ignition switch, and turn the key to the ON/RUN
position.
NOTE:
•The driver’s door key cylinder cannot arm
or disarm the Vehicle Security Alarm.
• When the Vehicle Security Alarm is
armed, the interior power door lock
switches will not unlock the doors. Vehicles Equipped with Keyless
Enter-N-Go
Either press the UNLOCK button on the RKE
transmitter, pull on the front driver or passenger
door handle (refer to “Passive Entry System” in
“Things To Know Before Starting Your Vehicle”
for further information) with a valid key fob in
range, or press the Keyless Enter-N-Go Start/
Stop button (requires at least one valid Key Fob
in the vehicle), or insert a valid Key Fob into the
ignition switch (if the Start/Stop button is re-
moved) and rotate it to the ON/RUN position.
The Vehicle Security Alarm is designed to pro-
tect your vehicle; however, you can create
conditions where the Vehicle Security Alarm will
give you a false alarm. If one of the previously-
described arming sequences has occurred,
the Vehicle Security Alarm will arm, regardless
of whether you are in the vehicle or not. If you
remain in the vehicle and open a door, the
alarm will sound. If this occurs, disarm the
Vehicle Security Alarm.
If the Vehicle Security Alarm is armed, and the
battery becomes disconnected, the Vehicle Security Alarm will remain armed when the
battery is reconnected. The exterior lights will
flash, the horn will sound, and the ignition will
not start the vehicle. If this occurs, disarm the
Vehicle Security Alarm.
ILLUMINATED ENTRYThe interior lights come on when you open any
door or use the Remote Keyless Entry (RKE)
transmitter to unlock any door. They will remain
on for approximately 30 seconds after all doors
are closed then fade to off.
The lights also will fade to off if you turn on the
ignition after you close all the doors. Refer to
“Electronic Vehicle Information Center (EVIC)/
Personal Settings (Customer-Programmable
Features)” in “Understanding Your Instrument
Panel” for further information.
NOTE:
None of the courtesy lights will operate if the
dimmer control is in the “defeat” position
(extreme downward position), unless the
overhead map/reading lights are turned on
manually.
16
Page 21 of 350
REMOTE KEYLESS ENTRY (RKE)This system allows you to lock or unlock the
doors or liftgate from distances up to approxi-
mately 33 ft (10 m) using a hand-held Key Fob
with RKE transmitter. The RKE transmitter does
not need to be pointed at the vehicle to activate
the system.
NOTE:
Inserting the Key Fob with RKE transmitter
into the ignition switch disables all buttons
on that RKE transmitter; however, the but-
tons on the remaining RKE transmitters will
continue to work. Driving at speeds 5 mph
(8 km/h) and above disables all RKE trans-
mitter buttons for all RKE transmitters.To Unlock the DoorsPress and release the UNLOCK button on the
RKE transmitter once to unlock the driver’s
door or twice to unlock all doors. The turn
signal lights will flash to acknowledge the un-
lock signal. The illuminated entry system will
also turn on.
Refer to “Passive Entry System” under “Things
To Know Before Starting Your Vehicle” for fur-
ther information.
Remote Key Unlock, Driver Door/All Doors
First Press
This feature lets you program the system to
unlock either the driver’s door or all doors, on
the first press of the UNLOCK button on the
RKE transmitter. To change the current setting,
proceed as follows:
•
For vehicles equipped with the Electronic
Vehicle Information Center (EVIC), refer to
“Electronic Vehicle Information Center (EVIC)/
Personal Settings (Customer-Programmable
Features)” in “Understanding Your Instrument
Panel” for further information.
Flash Lights with Remote Key Lock
This feature will cause the turn signal lights to
flash when the doors are locked or unlocked
with the RKE transmitter. This feature can be
turned on or off. To change the current setting,
proceed as follows:
•
For vehicles equipped with the Electronic
Vehicle Information Center (EVIC), refer to
“Electronic Vehicle Information Center (EVIC)/
Personal Settings (Customer-Programmable
Features)” in “Understanding Your Instrument
Panel” for further information.
Turn Headlights On with Remote Key
Unlock
This feature activates the headlights for up to
90 seconds when the doors are unlocked with
the RKE transmitter. The time for this feature is
programmable on vehicles equipped with the
Electronic Vehicle Information Center (EVIC).
Refer to “Electronic Vehicle Information Center
(EVIC)/Personal Settings (Customer-Program-
mable Features)” in “Understanding Your In-
strument Panel” for further information.
Key Fob with RKE Transmitter
17
Page 22 of 350
To Lock the DoorsPress and release the LOCK button on the RKE
transmitter to lock all doors. The turn signal
lights will flash to acknowledge the signal.
Refer to “Passive Entry System” under “Things
To Know Before Starting Your Vehicle” for fur-
ther information.
To Release the Liftgate Flipper
Glass
Press the FLIPPER GLASS/LIFTGATE RE-
LEASE button two times (the second press
within 5 seconds of the first press) to open
liftgate flipper glass.
WARNING!
Driving with the flipper glass open can allow
poisonous exhaust gases into your vehicle.
You and your passengers could be injured by
these fumes. Keep the flipper glass closed
when you are operating the vehicle.
Remote Open Window Feature —
If Equipped
This feature allows you to remotely lower both
front door windows at the same time. To use this
feature, press and release the UNLOCK button
on the RKE transmitter and then immediately
press and hold the UNLOCK button until the
windows lower to the level desired or until they
lower completely.
Programming Additional
Transmitters
Programming Key Fobs or RKE transmitters
may be performed at an authorized dealer.
Transmitter Battery ReplacementThe recommended replacement battery is one
CR2032 battery.
NOTE:
•Perchlorate Material — special handling
may apply. See www.dtsc.ca.gov/
hazardouswaste/perchlorate
• Do not touch the battery terminals that
are on the back housing or the printed
circuit board. 1. Remove the emergency key by sliding the
mechanical latch at the top of the RKE trans-
mitter sideways with your thumb and then pull
the key out with your other hand.
2. Insert the tip of the emergency key or a #2
flat blade screwdriver into the slot and gently
pry the two halves of the RKE transmitter apart.
Make sure not to damage the seal during
removal.Emergency Key Removal
18
Page 29 of 350
WARNING!
Never leave children in a vehicle with the key
in the ignition switch or leave a vehicle with
Keyless Enter-N-Go in the ACC or ON/RUN
position. Occupants, particularly unattended
children, can become entrapped by the win-
dows while operating the power window
switches. Such entrapment may result in se-
rious injury or death.
Auto-Down
Both the driver and front passenger window
switches have an “Auto-Down” feature. Press
the window switch past the first detent, release,
and the window will go down automatically. To
cancel the “Auto-Down” movement, operate
the switch in either the up or down direction
and release the switch.
To open the window part way, press to the first
detent and release it when you want the win-
dow to stop. The power window switches remain active for
10 minutes after the ignition has been turned
OFF. Opening either front door will cancel this
feature.
Auto Up Feature with Anti-Pinch Protection —
Driver and Front Passenger Door Only
Lift the window switch to the second detent,
release, and the window will go up automati-
cally.
To stop the window from going all the way up
during the Auto Up operation, push down on
the switch briefly.
To close the window part way, lift the window
switch to the first detent and release when you
want the window to stop.
NOTE:
If the window runs into any obstacle during
Auto Up it will reverse direction and then go
back down. Remove the obstacle and use
the window switch again to close the win-
dow. Any impact due to rough road condi-
tions may trigger the auto reverse function
unexpectedly during Auto Up. If this hap-pens, pull the switch lightly to the first
detent and hold it to close the window manu-
ally.
WARNING!
There is no anti-pinch protection when the
window is almost closed. Be sure to clear all
objects from the window before closing.
Resetting the Auto Up Feature
Should the Auto Up feature stop working, the
window probably needs to be reset. To reset
Auto Up:
1. Pull the window switch up to close the
window completely and continue to hold the
switch up for an additional two seconds after
the window is closed.
2. Push the window switch down firmly to the
second detent to open the window completely
and continue to hold the switch down for an
additional two seconds after the window is fully
open.
25
Page 31 of 350
Once the liftgate flipper glass has been
opened, connection to the rear window wiper is
interrupted, preventing activation of the rear
wiper blade while the flipper glass is open.
NOTE:
If a malfunction to the liftgate latch should
occur, an emergency liftgate latch release
can be used to open the liftgate. The emer-
gency liftgate latch release can be accessed
through a snap-in cover located on the lift-
gate trim panel.
WARNING!
Driving with the flipper glass open can allow
poisonous exhaust gases into your vehicle.
You and your passengers could be injured by
these fumes. Keep the flipper glass closed
when you are operating the vehicle.
Power Liftgate — If Equipped
The power liftgate may be opened
manually or by pressing the LIFT-
GATE button on the Remote Key-
less Entry (RKE) transmitter. Press
the LIFTGATE button on the RKEtransmitter twice within five seconds, to open
the power liftgate. Once the liftgate is open,
pressing the button twice within five seconds a
second time will close the liftgate.
The power liftgate may also be opened or
closed by pressing the LIFTGATE button lo-
cated on the front overhead console, or closed
by pressing the LIFTGATE button located on
left rear trim, near the liftgate opening. Pressing
the LIFTGATE button located on left rear trim
once will close the liftgate only, this button
cannot be used to open the liftgate.
When the LIFTGATE button on the RKE trans-
mitter is pressed two times, the turn signals will
flash twice to signal that the liftgate is opening
or closing.
NOTE:
In the event of a power malfunction to the
liftgate, an emergency liftgate latch release
can be used to open the liftgate. The emer-
gency liftgate latch release can be accessed
through a snap-in cover located on the lift-
gate trim panel.
WARNING!
During power operation, personal injury or
cargo damage may occur. Ensure the liftgate
travel path is clear. Make sure the liftgate is
closed and latched before driving away.
NOTE:
• If anything obstructs the power liftgate
while it is closing or opening, the liftgate
will automatically reverse to the closed or
open position, provided it meets suffi-
cient resistance.
• There are also pinch sensors attached to
the side of the liftgate. Light pressure
anywhere along these strips will cause
the liftgate to return to the open position.
• The power liftgate must be in the full open
position for rear liftgate close button or
overhead console close button to oper-
ate. If the liftgate is not fully open, press
the Liftgate button on the Key Fob to fully
open the liftgate, and then press it again
to close.
27
Page 40 of 350
4. The AHR front soft foam and trim half should
lock into the back decorative plastic half.
NOTE:
•If you have difficulties or problems reset-
ting the Active Head Restraints, see an
authorized dealer.
• For safety reasons, have the Active Head
Restraints checked by a qualified special-
ist at an authorized dealer.Enhanced Seat Belt Use Reminder
System (BeltAlert )
BeltAlert is a feature intended to remind the
driver and front passenger (if equipped with
front passenger BeltAlert ) to fasten their seat-
belts. This feature is active whenever the igni-
tion is on. If the driver or front seat passenger is
unbelted, the Seat Belt Reminder Light will turn
on and remain on until both front seatbelts are
fastened. BeltAlert triggers within 60 seconds
of vehicle speed over 5 mph (8 km/h). The
reminder sequence lasts for 96 seconds or until
the respective seatbelts are fastened. After the
sequence completes, the Seat Belt Reminder
Light remains illuminated until front belts are
fastened. The driver should instruct all other
occupants to fasten their seatbelts. If a front
seatbelt is unbuckled while traveling at speeds
greater than 5 mph (8 km/h), BeltAlert will
chime as a single notification and illuminate the
Seat Belt Reminder Light, then will proceed to
the 96 second reminder sequence.
The front passenger seat BeltAlert is not ac-
tive when the front passenger seat is unoccu-
pied. BeltAlert may be triggered when an
animal or heavy object is on the front passen- ger seat or when the seat is folded flat (if
equipped). It is recommended that pets be
restrained in the rear seat in pet harnesses or
pet carriers that are secured by seat belts, and
cargo is properly stowed.
NOTE:
•
BeltAlert can be enabled or disabled by
your authorized dealer.
• Chrysler Group LLC does not recommend
deactivating BeltAlert .
Although BeltAlert has been deactivated,
the Seat Belt Reminder Light will continue to
illuminate while the driver seat belt remains
unfastened.
Seatbelt Lock OutThe center rear seat belt system has a lock out
feature that will not allow you to extract the
center webbing unless the rear seat upper
latch is engaged.
Seat Belts and Pregnant WomenWe recommend that pregnant women use the
seat belts throughout their pregnancy. Keeping
the mother safe is the best way to keep the
baby safe.
AHR In Reset Position
36
Page 41 of 350
Pregnant women should wear the lap part of
the belt across the thighs and as snug across
the hips as possible. Keep the belt low so that
it does not come across the abdomen. That
way the strong bones of the hips will take the
force if there is an accident.
Supplemental Restraint System
(SRS) — Airbags
This vehicle has Advanced Front Airbags for
both the driver and front passenger as a
supplement to the seat belt restraint systems.
The driver’s Advanced Front Airbag is mounted
in the center of the steering wheel. The passen-
ger’s Advanced Front Airbag is mounted in the
instrument panel, above the glove compart-
ment. The words SRS AIRBAG are embossed
on the airbag covers. In addition, the vehicle is
equipped with a driver side knee airbag
mounted in the instrument panel below the
steering column.The Advanced Front Airbags have a multistage
inflator design. This allows the airbag to have
different rates of inflation based on the severity
and type of collision.
This vehicle is equipped with Supplemental
Side Airbag Inflatable Curtains (SABIC) to pro-
tect the driver, front, and rear passengers sit-
ting next to a window. The SABIC airbags, are
located above the side windows and their
covers are also labeled: SRS AIRBAG.This vehicle is equipped with Supplemental
Seat-Mounted Side Airbags (SAB) to provide
enhanced protection for an occupant during a
side impact. The Supplemental Seat-Mounted
Side Airbags are located in the outboard side
of the front seats.
NOTE:
•
Airbag covers may not be obvious in the
interior trim; but they will open during
airbag deployment.
• After any accident, the vehicle should be
taken to an authorized dealer immedi-
ately.
Airbag System Components
Your vehicle may be equipped with the follow-
ing airbag system components:
• Occupant Restraint Controller (ORC)
• Airbag Warning Light
• Steering Wheel and Column
• Instrument Panel
• Supplemental Driver Side Knee Airbag
• Knee Impact BolsterAdvanced Front Airbag and Knee Bolster
Locations
1 — Driver and Passenger Ad-
vanced Front Airbags 3 — Knee
Bolster
2 — Driver Knee Airbag
37