parking brake JEEP RENEGADE 2017 1.G Owners Manual

RUN
•Driving position.
• All the electrical devices are available.
NOTE: The vehicle will not start if the key fob is located
inside the cargo area and the liftgate is opened.
WARNING!
• When leaving the vehicle, always remove the key fob
from the vehicle and lock your vehicle.
• Never leave children alone in a vehicle, or with
access to an unlocked vehicle.
• Allowing children to be in a vehicle unattended is
dangerous for a number of reasons. A child or others
could be seriously or fatally injured. Children
should be warned not to touch the parking brake,
brake pedal or the gear selector.
• Do not leave the key fob in or near the vehicle, or in
a location accessible to children, and do not leave the
ignition in the ON or RUN mode. A child could
operate power windows, other controls, or move the
vehicle.
(Continued)
WARNING! (Continued)
•Do not leave children or animals inside parked
vehicles in hot weather. Interior heat build-up may
cause serious injury or death.
CAUTION!
An unlocked vehicle is an invitation for thieves. Al-
ways remove key fob from the vehicle and lock all
doors when leaving the vehicle unattended.
NOTE: For further information, refer to Starting Proce-
dures, inStarting And Operating.
REMOTE STARTING SYSTEM — IF EQUIPPED
This system uses the key fob to start the engine
conveniently from outside the vehicle while still
maintaining security. The system has a range of
approximately 328ft (100m).
3
GETTING TO KNOW YOUR VEHICLE 23

WARNING!
•For personal security and safety in the event of a
collision, lock the vehicle doors before you drive as
well as when you park and leave the vehicle.
• When leaving the vehicle, always remove the key fob
from the vehicle and lock your vehicle. Always make
sure the ignition is in “OFF” mode, remove the key
fob from the vehicle and lock the vehicle. Unsuper-
vised use of vehicle equipment may cause severe
personal injuries or death.
• Never leave children alone in a vehicle, or with
access to an unlocked vehicle. Allowing children to
be in a vehicle unattended is dangerous for a number
of reasons. A child or others could be seriously or
fatally injured. Children should be warned not to
touch the parking brake, brake pedal or the gear
selector.
• Do not leave the key fob in or near the vehicle, or in
a location accessible to children, and do not leave the
ignition in the ON or RUN mode. A child could
operate power windows, other controls, or move the
vehicle.
Power Door Locks
A power door lock switch is located on each of the front
door trim panels. Use this switch to lock or unlock the
doors, liftgate and fuel door.
NOTE: The key fob may not be able to be detected by the
vehicle keyless-go system if it is located next to a mobile
phone, laptop or other electronic device; these devices may
block the key fob’s wireless signal and prevent the
keyless-go system from starting the vehicle.
Power Door Lock Switch
3
GETTING TO KNOW YOUR VEHICLE 31

2. Remove the emergency key from the key fob withRemote Control housing.
NOTE: The Emergency Key can be inserted into the door
lock cylinder from either direction.WARNING!
• Never leave children alone in a vehicle, or with
access to an unlocked vehicle. Allowing children to
be in a vehicle unattended is dangerous for a number
of reasons. A child or others could be severely
injured or killed. Children should be warned not to
touch the parking brake, brake pedal, or the gear
selector. Do not leave the key fob in or near the
vehicle, or in a location accessible to children, and do
not leave the ignition in the ON or RUN mode. A
child could start the vehicle, operate power win-
dows, other controls, or move the vehicle.
• Do not leave children or animals inside parked
vehicles in hot weather. Interior heat buildup may
cause them to be severely injured or killed
Dead Lock Device — If Equipped
The Dead Lock Device is a safety device that prevents the
use of the internal door handles of the vehicle and the
power door lock switch.
This device prevents the doors from opening within the
passenger compartment.
Emergency Key Release
1 — Emergency Key Release Button
2 — Emergency Key 36 GETTING TO KNOW YOUR VEHICLE

Security
By selecting the item “Security,” you can make the follow-
ing adjustments:
•Speed Warning:
Set the vehicle speed limit (km/h or MPH), which the
driver is notified through a visual and acoustic signaling
(display of a message and a symbol on the display).
When the speed warning is set, the icon should remain
visualized for the same duration time of the pop up. If the
driver exceeded the speed set the icon should remain for
however long the vehicle is over the set speed.
Driver may also turn the Speed Warning “OFF” should you
choose not to use this feature.
• Seat Belt Reminder:
This function is only viewable when the Seat Belt Re-
minder (SBR) system is active.
• Hill Start Assist (If Equipped):
Activation/Deactivation of the Hill Start Assist system. Safety & Assistance
By selecting the item
Safety & Assistance, you can make
the following adjustments:
• Forward Collision Warning
• Forward Collision Warning Sensitity
• ParkSense (If Equipped): a selection of the type of
information provided by ParkSense
• Rear Parks (If Equipped) Vol.: selection of the volume of
acoustic signals provided by ParkSense
• ParkSense (If Equipped) Vol.: a selection of the volume
of acoustic signals provided by ParkSense
• Front Parks. Vol.: selection of the volume of the beeps
provided by ParkSense
• Warning Buzzer Volume
• Brake Service (If Equipped): activation of the procedure
to carry out braking system maintenance
• Auto Park Brake (If Equipped): enable/disable auto-
insertion of the Electric Parking Brake
• Rain Sensing Wipers
• Lanesense Warning (If Equipped)
4
GETTING TO KNOW YOUR INSTRUMENT PANEL 131

Brake Warning Light
Red TelltaleLight What It Means
English
Metric
Brake Warning Light
This light monitors various brake functions, including brake fluid level and parking brake appli-
cation. If the brake light turns on it may indicate that the parking brake is applied, that the brake
fluid level is low, or that there is a problem with the anti-lock brake system reservoir.
If the light remains on when the parking brake has been disengaged, and the fluid level is at the
full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunc-
tion or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System
(ABS) / Electronic Stability Control (ESC) system. In this case, the light will remain on until the
condition has been corrected. If the problem is related to the brake booster, the ABS pump will
run when applying the brake, and a brake pedal pulsation may be felt during each stop.
The dual brake system provides a reserve braking capacity
in the event of a failure to a portion of the hydraulic
system. A leak in either half of the dual brake system is
indicated by the Brake Warning Light, which will turn on
when the brake fluid level in the master cylinder has
dropped below a specified level.
The light will remain on until the cause is corrected. NOTE:
The light may flash momentarily during sharp
cornering maneuvers, which change fluid level conditions.
The vehicle should have service performed, and the brake
fluid level checked.
136 GETTING TO KNOW YOUR INSTRUMENT PANEL

If brake failure is indicated, immediate repair is necessary.
WARNING!
Driving a vehicle with the red brake light on is
dangerous. Part of the brake system may have failed. It
will take longer to stop the vehicle. You could have a
collision. Have the vehicle checked immediately.
Vehicles equipped with the Anti-Lock Brake System (ABS)
are also equipped with Electronic Brake Force Distribution
(EBD). In the event of an EBD failure, the Brake Warning
Light will turn on along with the ABS Light. Immediate
repair to the ABS system is required.
Operation of the Brake Warning Light can be checked by
turning the ignition switch from the STOP/OFF position to
the ON/RUN position. The light should illuminate for
approximately two seconds. The light should then turn off
unless the parking brake is applied or a brake fault is
detected. If the light does not illuminate, have the light
inspected by an authorized dealer. The light also will turn on when the parking brake is
applied with the ignition switch in the ON/RUN position.
NOTE:
This light shows only that the parking brake is
applied. It does not show the degree of brake application.
4
GETTING TO KNOW YOUR INSTRUMENT PANEL 137

Periodic Safety Checks You Should Make Outside
The Vehicle
Tires
Examine tires for excessive tread wear and uneven wear
patterns. Check for stones, nails, glass, or other objects
lodged in the tread or sidewall. Inspect the tread for cuts
and cracks. Inspect sidewalls for cuts, cracks, and bulges.
Check the wheel nuts for tightness. Check the tires (includ-
ing spare) for proper cold inflation pressure.
Lights
Have someone observe the operation of brake lights and
exterior lights while you work the controls. Check turn
signal and high beam indicator lights on the instrument
panel.
Door Latches
Check for proper closing, latching, and locking.
Fluid Leaks
Check area under vehicle after overnight parking for fuel,
engine coolant, oil, or other fluid leaks. Also, if gasoline
fumes are detected, or if fuel or brake fluid leaks are
suspected, the cause should be located and corrected
immediately.
5
SAFETY 247

STARTING THE ENGINE
Before starting your vehicle, adjust your seat, adjust the
inside and outside mirrors, fasten your seat belt, and if
present, instruct all other occupants to buckle their seat
belts.
WARNING!
•Never leave children alone in a vehicle, or with
access to an unlocked vehicle.
• Allowing children to be in a vehicle unattended is
dangerous for a number of reasons. A child or others
could be seriously or fatally injured. Children
should be warned not to touch the parking brake,
brake pedal or the gear selector.
• Do not leave the key fob in or near the vehicle (or in
a location accessible to children), and do not leave
the ignition in the ON or RUN mode. A child could
operate power windows, other controls, or move the
vehicle.
Start the engine with the gear selector in the NEUTRAL or
PARK position. Apply the brake before shifting to any
driving range. Manual Transmission
Proceed as follows:
1. Set the Electric Park Brake (EPB) and put the gear
selector in the NEUTRAL position.
2. Press the clutch pedal to the floor, without pressing the accelerator.
3. Cycle the ignition to the START mode and release it as soon as the engine is started.
4. If the engine does not start, place the ignition in the OFF mode and wait 10-15 seconds before attempting to
restart the engine.
Automatic Transmission
Proceed as follows:
1. Set the Electric Park Brake (EPB) and put the gear selector in the PARK or NEUTRAL position.
2. Press on the brake pedal, without pressing the accelera- tor.
3. Cycle the ignition to the START mode and release it as soon as the engine is started.
6
STARTING AND OPERATING 251

The engine oil installed in the engine at the factory is a
high-quality energy conserving type lubricant. Oil changes
should be consistent with anticipated climate conditions
under which vehicle operations will occur. For the recom-
mended viscosity and quality grades, refer to “Dealer
Service” in “Servicing And Maintenance”.
CAUTION!
Never use Non-Detergent Oil or Straight Mineral Oil
in the engine or damage may result.
NOTE: A new engine may consume some oil during its
first few thousand miles (kilometers) of operation. This
should be considered a normal part of the break-in and not
interpreted as a problem.
ELECTRIC PARK BRAKE (EPB)
Your vehicle is equipped with an Electric Park Brake
System (EPB) that offers simple operation, and some
additional features that make the parking brake more
convenient and useful.
The parking brake is primarily intended to prevent the
vehicle from rolling while parked. Before leaving the vehicle, make sure that the parking brake is applied. Also,
be certain to leave the transmission in PARK.
The EPB switch is located in the center console.
You can engage the EPB in two ways;
•
Manually, by applying the park brake switch.
• Automatically, by enabling the Auto Park Brake feature
in the customer programmable features section of the
Uconnect settings or in “Safe Hold” conditions.
Electric Park Brake Switch
6
STARTING AND OPERATING 255

To apply the EPB manually, pull up on the switch momen-
tarily. You may hear a slight whirring sound from the back
of the vehicle while the EPB engages. Once the parking
brake is fully engaged, the BRAKE warning lamp in the
instrument cluster and an indicator on the switch will
illuminate. If your foot is on the brake pedal while you
apply the EPB, you may notice a small amount of brake
pedal movement. The EPB can be applied even when the
ignition is in the OFF mode however, it can only be
released when the ignition is in the RUN mode.
NOTE:The EPB fault lamp will illuminate if the EPB
switch is held for longer than 60 seconds in either the
released or applied position. The light will extinguish upon
releasing the switch.
If the Auto Park Brake feature is enabled, the EPB will
automatically engage whenever the transmission is moved
into PARK, or with a manual transmission, when the
ignition switch is in the STOP/OFF position. If your foot is
on the brake pedal, you may notice a small amount of
brake pedal movement while the EPB is engaging.
The electric park brake will be automatically released if the
driver’s seat belt is buckled (only in case of automatic
transmission) and driver’s intention to start (in forward or
reverse direction) is recognized by the system To release the EPB manually, the ignition must be in the
RUN mode. Put your foot on the brake pedal, then push
the EPB switch down momentarily. You may hear a slight
whirring sound from the back of the car while the parking
brake disengages. You may also notice a small amount of
movement in the brake pedal. Once the EPB is fully
disengaged, the BRAKE warning lamp in the instrument
cluster and the LED indicator on the switch will extinguish.
NOTE:
•
When parking on a hill, it is important to turn the front
wheels toward the curb on a downhill grade and away
from the curb on an uphill grade. Apply the EPB before
placing the gear selector in PARK, otherwise the load on
the transmission locking mechanism may make it diffi-
cult to move the gear selector out of PARK. The EPB
should always be applied whenever the driver is not in
the vehicle.
• If the clutch pedal is released at the same time the gas
pedal is pressed, the EPB will be automatically released
(manual transmissions only).
256 STARTING AND OPERATING