warning JEEP WRANGLER 2004 TJ / 2.G Manual Online

Windshield Washers
The fluid reservoir in the engine compartment should be
checked for fluid level at regular intervals. Fill the
reservoir with windshield antifreeze (not radiator anti-
freeze) rated not to freeze at -25ÉF (-31ÉC). Operate the
system for a few seconds to flush out the residual water.
WARNING!
Commercial windshield washer solvents are flam-
mable. They could ignite and burn you. Care must
be exercised when filling or working around the
washer solution.
Windshield Washer Aiming
To change the aim of the windshield washers, place a
safety pin into the nozzle opening and move the nozzle
slightly. Continue making slight adjustments until you
obtain the desired pattern.
Exhaust System
The best protection against carbon monoxide entry into
the vehicle body is a properly maintained engine exhaust
system.
238 MAINTAINING YOUR VEHICLE

If you notice a change in the sound of the exhaust system;
or if the exhaust fumes can be detected inside the vehicle;
or when the underside or rear of the vehicle is damaged;
have an authorized technician inspect the complete ex-
haust system and adjacent body areas for broken, dam-
aged, deteriorated, or mispositioned parts. Open seams
or loose connections could permit exhaust fumes to seep
into the passenger compartment. In addition, inspect the
exhaust system each time the vehicle is raised for lubri-
cation or oil change. Replace as required.
Cooling System
WARNING!
You or others can be badly burned by hot coolant or
steam from your radiator. If you see or hear steam
coming from under the hood, don't open the hood
until the radiator has had time to cool. Never try to
open a cooling system pressure cap when the radia-
tor or coolant bottle is hot.
Coolant Checks
Check coolant protection every 12 months (before the
onset of freezing weather, where applicable). If coolant is
dirty or rusty in appearance, the system should be
drained, flushed and refilled with fresh coolant.
Check the front of the radiator for any accumulation of
bugs, leaves, etc. Clean the radiator by gently spraying
water from a garden hose at the back of the core.
Check the engine cooling system hoses for condition and
tightness of connection. Inspect the entire system for
leaks. Any hoses that show cuts or severe abrasion must
be replaced.
Cooling System Ð Drain, Flush, And Refill
At the intervals shown in the appropriate ªMaintenance
Schedule,º the system should be drained, flushed, and
refilled.
If the solution is dirty and contains a considerable
amount of sediment, clean and flush with reliable cooling
system cleaner. Follow with a thorough rinsing to remove
all deposits and chemicals.
MAINTAINING YOUR VEHICLE 239
7

Adding Coolant
When adding coolant, a minimum solution of recom-
mended 50% ethylene glycol antifreeze coolant in water
should be used. Use higher concentrations (not to exceed
70%) if temperatures below -37ÉF (-38ÉC) are anticipated.
Use only high purity water such as distilled or deionized
water when mixing the water/antifreeze solution. The
use of lower quality water will reduce the amount of
corrosion protection in the engine cooling system.
NOTE:Mixing coolant types will decrease the life of the
engine coolant and will require more frequent engine
coolant changes.
Please note that it is the owner's responsibility to main-
tain the proper level of protection against freezing ac-
cording to the temperatures occurring in the area where
the vehicle is operated.
Cooling System Pressure Cap
The cap must be fully tightened to prevent loss of
coolant, and to insure that coolant will return to the
radiator from the coolant reserve tank.The cap should be inspected and cleaned if there is any
accumulation of foreign material on the sealing surfaces.
WARNING!
The warning words DO NOT OPEN HOT on the
cooling system pressure cap are a safety precaution.
Never add coolant when the engine is overheated.
Do not loosen or remove the cap to cool an over-
heated engine. Heat causes pressure to build up in
the cooling system. To prevent scalding or injury, do
not remove the pressure cap while the system is hot
or under pressure.
Coolant Level
The coolant bottle provides a quick visual method for
determining that the coolant level is adequate. The
coolant level must be at the FULL mark or above the
ADD mark on the bottle.
The radiator normally remains completely full, so there is
not need to remove the radiator cap unless checking for
coolant freeze point or replacing coolant. Advise your
MAINTAINING YOUR VEHICLE 241
7

Pay particular attention to the hoses nearest to high heat
sources such as the exhaust manifold. Inspect hose rout-
ing to be sure hoses do not touch any heat source or
moving component that may cause heat damage or
mechanical wear.
Insure nylon tubing in these areas has not melted or
collapsed. Inspect all hose connections such as clamps
and couplings to make sure they are secure and no leaks
are present. Components should be replaced immedi-
ately if there is any evidence of degradation that could
cause failure.
Brake System
In order to assure brake system performance, all brake
system components should be inspected periodically.
Refer to the appropriate ªMaintenance Scheduleº in
Section 8 for suggested service intervals.
WARNING!
Riding the brakes can lead to brake failure and
possibly an accident. Driving with your foot resting
or riding on the brake pedal can result in abnormally
high brake temperatures, excessive lining wear, and
possible brake damage. You wouldn't have your full
braking capacity in an emergency.
Brake and Power Steering System Hoses
When servicing the vehicle for scheduled maintenance,
inspect surface of hoses for evidence of heat and me-
chanical damage. Hard and brittle rubber, cracking, tears,
cuts, abrasion, and excessive swelling suggest deteriora-
tion of the rubber. Particular attention should be made to
examining those hose surfaces nearest to high heat
sources, such as the exhaust manifold.
Inspect all hose clamps and couplings to make sure they
are secure and no leaks are present.
NOTE:Inspection of brake hoses should be done
whenever the brake system is serviced and every engine
oil change.
MAINTAINING YOUR VEHICLE 243
7

WARNING!
Worn brake hoses can burst and cause brake failure.
You could have an accident. If you see any signs of
cracking, scuffing, or worn spots, have the brake
hoses replaced immediately.
Brake Master Cylinder
The fluid level in the master cylinder should be checked
when performing under hood services, or immediately if
the BRAKE warning light shows system failureBe sure to clean the top of the master cylinder area before
removing the cap. If necessary, add fluid to bring the
fluid level up to the requirements described on the brake
fluid reservoir. With disc brakes, fluid level can be
expected to fall as the brake pads wear. Brake fluid level
should be checked when pads are replaced. However,
low fluid level may be caused by a leak and a checkup
may be needed.
Use only manufacturer's recommended brake fluid, refer
to Recommended Fluids, Lubricants, and Genuine Parts
for correct fluid type.
WARNING!
²Use of a brake fluid that may have a lower initial
boiling point or unidentified as to specification,
may result in sudden brake failure during hard
prolonged braking. You could have an accident.
²Overfilling the brake fluid reservoir can result in
spilling brake fluid on hot engine parts and the
brake fluid catching fire.
244 MAINTAINING YOUR VEHICLE

²Use MopartTouch Up Paint on scratches or chips as
soon as possible. Your authorized dealer has touch up
paint to match the color of your vehicle.
²Aluminum wheels should be cleaned regularly with
mild soap and water to prevent corrosion. To remove
heavy soil, select a non-abrasive, non-acidic cleaner.
Do not use scouring pads or metal polishes. Avoid
automatic car washes that use acidic solutions or harsh
brushes that may damage the wheels' protective fin-
ish.
Interior Care
Use MopartFabric Cleaner to clean fabric upholstery
and carpeting.
Use MopartVinyl Cleaner to clean vinyl or leather
upholstery.
MopartVinyl Cleaner is specifically recommended for
interior vinyl trim.
WARNING!
Do not use volatile solvents for cleaning purposes.
Many are potentially flammable, and if used in
closed areas they may cause respiratory harm.
Glass Surfaces
All glass surfaces should be cleaned on a regular basis
with any commercial household-type glass cleaner.
Never use an abrasive type cleaner. Use caution when
cleaning inside rear windows equipped with electric
defrosters. Do not use scrapers or other sharp instru-
ments which may scratch the elements.
When cleaning the rear view mirror, spray cleaner on the
towel or rag that you are using. Do not spray cleaner
directly on the mirror.
Carpet
Vacuum your carpet regularly to prevent a soil build-up.
Shampoo soiled carpet with a reliable upholstery cleaner,
using a natural sponge or soft bristle brush. After carpet
dries, vacuum it thoroughly.
252 MAINTAINING YOUR VEHICLE

WARNING!
Only remove the carpet for cleaning purposes. It
provides insulation against high floor pan tempera-
tures. You or your passengers could be burned if the
carpet is not properly in place. Always put the carpet
back into the vehicle before driving.
Follow These Steps To Remove The Carpet:
1. Unsnap the front and rear floor carpets. A snap is
located on the outboard side of each front seat.
2. Remove the attachment cap from the front footwell
area on both the driver and passenger side. The cap is
removed by pulling it straight out.
3. Remove the front and rear floor carpets.
4. Remove the cargo floor and wheelhouse carpets.
NOTE:If your vehicle is equipped with an Add-A-
TrunkŸ it must be removed to be able to remove the cargo
floor and wheelhouse carpets. For Add-A-TrunkŸ removal
procedure, refer to ªStorageº in Section 3 of this manual.
Follow These Steps To Replace The Carpet:
1. Place the front floor carpets in the vehicle.
2. Attach the carpet to the studs in the footwell and press
on the attachment caps to secure the carpet.
3. Place rear floor carpet in vehicle and snap rear carpet
to front floor carpet.
4. Install wheelhouse carpet followed by the cargo floor
carpet.
5. Reinstall Add-A-TrunkŸ if so equipped.
Seat Belt Maintenance
Do not bleach, dye or clean the belts with chemical
solvents or abrasive cleaners. This will weaken the fabric.
Sun damage will also weaken the fabric.
If the belts need cleaning, use a mild soap solution or
lukewarm water. Do not remove the belts from the
vehicle to wash them.
Replace the belts if they appear frayed or worn or if the
buckles do not work properly.
MAINTAINING YOUR VEHICLE 253
7

About Your Brakes...................... 177
Add-A-Trunk........................... 65
Adding Washer Fluid.................... 155
Air Cleaner, Engine..................... 234
Air Conditioner Maintenance.............. 235
Air Conditioning....................... 151
Air Conditioning Controls................ 152
Air Conditioning, Operating Tips........... 154
Air Conditioning Refrigerant.............. 236
Air Filter............................. 234
Air Pressure, Tires...................... 192
Airbag................................ 22
Airbag Deployment...................... 27
Airbag Light........................29,118
Airbag Maintenance...................... 29
Airbag On/Off Switch.................... 26
Alignment and Balance.................. 195
Alterations/Modifications, Vehicle............ 8
Antenna, Satellite Radio.................. 147
Antifreeze (Engine Coolant)............... 258
Anti-Lock Brake System.................. 179
Anti-Lock Warning Light................. 119
Appearance Care....................... 248Ashtray............................... 62
Ashtrays and Lighter..................... 62
Automatic Dimming Mirror................ 46
Automatic Transmission...............165,245
Adding Fluid........................ 246
Fluid and Filter Changes................ 245
Fluid Level Check..................... 245
Fluid Type.......................... 245
Gear Ranges......................... 166
Shifting............................ 165
Special Additives..................... 246
Torque Converter..................... 170
Auxiliary Electrical Outlet................. 63
Auxiliary Power Outlet................... 63
Battery............................... 234
Emergency Starting.................... 216
Voltmeter........................... 116
Belts, Drive........................... 231
Belts, Seat............................. 17
Body Mechanism Lubrication.............. 237
Brake System.......................... 243
Anti-Lock........................... 179
288 INDEX

Hoses.............................. 243
Master Cylinder...................... 244
Parking............................ 175
Warning Light....................... 119
Brakes............................... 177
Brake/Transmission Interlock.............. 166
Break-In Recommendations, New Vehicle...... 39
Bulb Replacement...................... 257
Calibration, Compass..................... 47
Capacities, Fluid....................... 258
Caps, Filler
Fuel............................... 200
Power Steering....................... 236
Car Washes........................... 249
Carpeting............................. 252
Cassette Tape and Player Maintenance....... 148
Cassette Tape Player.........126,130,132,140,142
Catalytic Converter..................... 232
Caution, Exhaust Gas..................... 40
CD Changer........................133,138
CD Player......................128,135,137
CD Player Maintenance.................. 149Cellular Phone......................... 149
Chains, Tire........................... 196
Changing A Flat Tire.................... 213
Chart, Tire Sizing....................... 185
Check Engine Light..................... 118
Child Restraint.....................29,33,36
Child Restraint Tether Anchors............. 33
Cigar Lighter........................... 62
Climate Control........................ 149
Clock................................ 120
Clutch Interlocking Ignition System......160,165
Compact Disc Maintenance............... 149
Compact Disc Player.................... 140
Compass.............................. 46
Compass Calibration..................... 47
Compass Variance....................... 48
Console............................... 65
Console, Floor.......................... 65
Contract, Service....................... 282
Converter, Catalytic..................... 232
Cooling System........................ 239
Adding Coolant (Antifreeze)............. 241
Coolant Capacity..................... 258
INDEX 289
10

Coolant Level........................ 241
Disposal of Used Coolant............... 240
Drain, Flush, and Refill................. 239
Inspection........................... 239
Points to Remember................... 242
Pressure Cap........................ 241
Selection of Coolant................240,258
Temperature Gauge.................... 118
Corrosion Protection.................... 248
Crankcase Emission Control System......... 234
Cruise Control.......................... 60
Cruise Light........................... 116
Cup Holder............................ 64
Customer Assistance.................... 280
Daytime Running Lights.................. 58
Dealer Service......................... 227
Defroster, Rear Window.................. 154
Defroster, Windshield.................151,153
Delay Wipers........................... 58
Deploying, Airbag....................... 27
Diagnostic System, Onboard............... 225
Dimmer Switch, Headlight................. 57Dipsticks
Oil (Engine)......................... 228
Disabled Vehicle Towing................. 219
Disposal
Engine Oil.......................... 231
Used Coolant........................ 240
Door Locks............................ 15
Doors................................ 15
Drive Belts............................ 231
Driving.............................. 181
Off-Pavement........................ 181
Off-Road........................... 181
On Hills............................ 182
On Slippery Surfaces.................. 181
When to Use Low Range............... 181
Dual Top.............................. 66
Electrical Outlet, Auxiliary................. 63
Electrical Power Outlets................... 63
Electronic Speed Control.................. 60
Emergency Brake....................... 175
Emergency, In Case of
Brake Warning Light................... 119
290 INDEX