lock JEEP WRANGLER UNLIMITED 2013 Workshop Manual

4. Install the soft top with the pivot bracket above the
sport bar bracket, lower the pivot bracket onto the
sport bar bracket mounting tab in a downward motion
to lock into tab (another person may be needed to help
with this operation). 5. Screw the pivot screws back into place using a #T30
Torx  head driver. Secure them until they are snug,
being careful not to cross-thread the screws or over-
tighten.200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

CAUTION! (Continued)• The hard top assembly must be positioned prop-
erly to ensure sealing. Improper installation can
cause water to leak into the vehicles interior.
• Careless handling and storage of the removable
roof panels may damage the seals, causing water to
leak into the vehicles interior.
• The front panel(s) must be positioned properly to
ensure sealing. Improper installation can cause
water to leak into the vehicles interior.
Front Panel(s) Removal
NOTE: Left panel must be removed before removing
right panel.
1. Fold down the sun visor, and move it to the side. 2. Turn the rear fasteners (knobs) (located on the over-
head speaker bar assembly) counterclockwise until
they can be removed.
3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 203

3. Turn the center L-shaped locks (two) from the center
of the roof panel. 4. Turn the rear L-shaped lock (located above the shoul-
der belt anchorage).204 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Front Panel(s) Installation With Rear Hard Top
Removed
1. Turn the left and right panels over and move the
spacer block (located on the rear of the panel) upward
90 degrees. NOTE: The front panel(s) must be positioned properly
to ensure sealing. Set the panels on the windshield frame
so that there is no overhang. Also, make sure that the
panels are sitting flush with the body.
2. Install the right panel first, then the left panel.
3. Reinstall the panel(s) using the same steps for removal
in reverse order.
Rear Hard Top Removal
1. Remove both front panels. Refer to “Front Panel(s)
Removal” in this section.
2. Open both doors.
3. Remove the two Torx  head screws that secure the
hard top at the B-pillar (near the top of the door) using
a #40 Torx  head driver (Four–Door Only).210 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

7. Release the red locking tab by pulling outward to the
right. 8. To remove the wiring harness press the tab and pull
downward to disconnect.
Red Locking Tab Press Tab To Disconnect212 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

5. Insert the slider feature of the knuckles into the door
frame tracks and slide the top forward. 6. Ensure that the top locks into the Sunrider  locking
mechanisms that are located above the front of the rear
doors.272 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

6. Secure the top by using the two provided straps. Each
strap will wrap around the side bow and Velcro  to
itself; use one strap on each side of the vehicle.
Closing The Sunrider 
Perform the above steps in the opposite order.
NOTE: Failure to fold the fabric rearward will allow the
material to sag and may block the rearview mirror. FOLDING WINDSHIELD
The fold-down windshield and removable side bars on
your vehicle are structural elements that can provide
some protection in some accidents. The windshield also
provides some protection against weather, road debris
and intrusion of small branches and other objects.
Do not drive your vehicle on-road with the windshield
down and the side bars removed as you lose the protec-
tion these structural elements can provide.
If required for certain off-road uses, the side bars can be
removed and the windshield folded down. However, the
protection afforded by these features is then lost. If you
remove the side bars and fold down the windshield,
drive slowly and cautiously. It is recommended that the
speed of the vehicle be limited to 10 mph (16 km/h), with
low range operation preferred if you are driving off-road
with the windshield folded down.286 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

WARNING!You or others could be injured if you carry the side
bars loose in your vehicle. Remove the side bars from
the vehicle or securely store them as described or
they may cause personal injury if an accident occurs.
See your authorized dealer for the cinch straps.
10. Remove the windshield wiper arms by first pulling
the wiper away from the windshield and out to the
“lock” position. Unsnap the wiper arm nut caps, and
remove the retaining nuts. Lift the wiper arms off and
store them in the center console or securely behind
the rear seat.
NOTE: It may be necessary to use a battery terminal
puller tool in order to separate the wiper arms from the
shaft after the nuts have been removed. 11. Remove the lower windshield plates by removing the
six black round-headed Torx  head screws (using a
#40 Torx  head driver) on each side of the base of the
windshield.290 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

REAR WINDOW FEATURES — HARD TOP ONLY
Rear Window Wiper/Washer — If Equipped
A rotary switch on the center portion of the control lever
(located on the right side of the steering column) controls
the operation of the rear wiper/washer function. Rotate the switch upward to the first detent
position for rear wiper operation.
Rotate the switch upward past the first detent to
activate the rear washer. The washer pump and
the wiper will continue to operate as long as the switch is
held. Upon release, the wiper will cycle two to three
times before returning to the set position.
If the rear wiper is operating when the ignition is turned
to the LOCK position, the wiper will automatically return
to the “Park” position. When the vehicle is restarted, the
wiper will resume function at whichever position the
switch is set at.
Rear Wiper/Washer Control
3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 293

INSTRUMENT CLUSTER DESCRIPTIONS
1. Fuel Gauge
The pointer shows the level of fuel in the fuel tank when
the ignition switch is in the ON/RUN position.
2. Charging System Light
This light shows the status of the electrical charg-
ing system. The light should come on when the
ignition switch is first turned to ON/RUN, and remain
on briefly as a bulb check. If the light stays on or comes
on while driving, turn off some of the vehicle’s non-
essential electrical devices or increase engine speed (if at
idle). If the charging system light remains on, it means
that the vehicle is experiencing a problem with the
charging system. Obtain SERVICE IMMEDIATELY. See
an authorized dealer.
If jump starting is required, refer to “Jump Starting
Procedures” in “What To Do In Emergencies”. 3. Front Fog Light Indicator — If Equipped
This indicator will illuminate when the front fog
lights are on.
4. Low Fuel Warning Light
When the fuel level reaches approximately 2.8 gal
(10.6L) this light will turn on and a single chime
will sound.
5. Speedometer
Indicates vehicle speed.
6. Front Axle Lock Indicator — If Equipped
Indicates when the front axle lock has been
activated.300 UNDERSTANDING YOUR INSTRUMENT PANEL