key KIA CADENZA 2014 Navigation System Quick Reference Guide

50
Answering a Call
Incoming call notice ▶ Press the
Accept button or the key
on the steering wheel remote
controller.
When there is an incoming on within
the connected phone, the bell will
sound and the phone number of the
other party will be displayed on the
incoming call pop-up, as shown here.
Operating Menus
during a Call
Ending a Call
While on a call ▶Press the
End button or the key
on the steering wheel remote
controller.
The Bluetooth® handsfree call will end.
0[미국_영어]AVN.indb 502013-03-18
Bluetooth® Handsfree

51
Switching Call to Bluetooth®
Phone
During handsfree call ▶ Press the
Private button or press and hold
the key (over 0.8 seconds)
on the steering wheel remote
controller.
The call will be switched from the
handsfree to the Bluetooth
® mobile
phone.
Switching Call to the Handsfree
During call on mobile phone ▶
Press the
Use Handsfree button
or press and hold the key
(over 0.8 seconds) on the steering
wheel remote controller.
The call will be switched from the
Bluetooth
® mobile phone to the car
handsfree.
0[미국_영어]AVN.indb 512013-03-18
Bluetooth® Handsfree

56
Device Information
Press ▶ Press
Bluetooth ▶ Press
Advanced Settings ▶ Press
Device Information .
• This feature allows you to check
device information.
Adjusting the Ring/Call Volume
While on a call ▶ Use the VOL
knob on the head unit or the
VOL + , VOL - keys on the
steering wheel remote controller to
adjust the ring/call volume.
0[미국_영어]AVN.indb 562013-03-18
Bluetooth® Handsfree

57
Setting Mic Volume
While on a call ▶ Press the
Outgoing Vol. ▶ Set Outgoing
Volume ▶ Press OK.
If you press the Mute button, the
outgoing volume is muted and blocked
to the other party.
Restore Factory Settings
Press the key
▶ Press
Setup ▶ Press Bluetooth ▶
Press
Advanced Settings ▶ Press
Restore Factory Settings .
0[미국_영어]AVN.indb 572013-03-18
Bluetooth® Handsfree

58
Starting Voice
Recognition
Starting Voice Recognition
Shortly press the key on the
steering wheel remote controller
(under 0.8 seconds) ▶ Say a
command.
Once voice recognition starts, the voice
command entry window and the six rep -
resentative commands are displayed.
• If voice recognition is in [Normal
Mode], then the system will say
“Please say a command after the
beep,” followed by a beep tone.
• If voice recognition is in [Expert
Mode], then you will only hear a
beep a “Beep~”.
Skipping Prompt Messages
While prompt message is being
stated ▶ Shortly press the
key on
the steering wheel remote controller.
(under 0.8 seconds
)
The prompt message is immediately
ended and the beep tone will sound.
After the “beep”, say the voice command.
Re-starting Voice Recognition
While system waits ▶ Shortly press
the
key on the steering wheel
remote controller. (under 0.8 seconds)
The command wait state will end and
the beep tone will sound. After the
“beep”, say the voice command.
0[미국_영어]AVN.indb 582013-03-18
Voice Recognition

59
Ending Voice
Recognition
While Voice Recognition is operating
▶ Press and hold the
key on
the steering wheel remote controller.
(over 0.8 seconds)

While using voice recognition, press -
ing a steering wheel remote control or
a different key will end voice recogni -
tion.

Illustration on Using
Voice
Recognition
(Setting Home as the
Destination)
Press the key. (under 0.8 seconds)
The system awaits for your command
and display a list of accessible com -
mands on the screen.
Destination
Please say a command
after the beep
BEEP
DestinationPlease say a command after the beep
Go Home
BEEP
0[미국_영어]AVN.indb 592013-03-18
Voice Recognition