ignition KIA CADENZA 2016 Features and Functions Guide

8
Electronic Stability Control (ESC)
The ESC system is designed to help stabilize the vehicle during cornering
maneuvers It is a good idea to keep the ESC turned on for daily driving
whenever possible
Press ESC button
A to turn Traction Control OFF/ON
To turn OFF both the Traction Control and Stability Control, press and hold for
more than 3 seconds Press again to turn ON
(Button panel located left of Steering Wheel)
Hill-Start Assist Control (HAC)
HAC helps prevent the vehicle from rolling backwards when accelerating
from a stop while on a steep incline The HAC automatically activates
whether the ESC is OFF or ON but does NOT activate when the ESC
has malfunctioned
REMINDER: The HAC does not operate when the gear shift is in the P (Park) or the N
(Neutral) position

REMINDERS:

•ESC is active by default at vehicle start-up When ignition is cycled, ESC will turn ON again

• The ESC Indicator Light in the instrument cluster will illuminate whenever the ESC is
in operation
For more information on Electronic Stability Control (ESC) and its specific features and
operations, please refer to your Owner’s Manual.


When HAC is active (e g , during initial acceleration from a stop on an incline),
you may notice that the brakes will momentarily remain engaged after you
depress the accelerator QUICK TIP
A
CADENZA FEATURES & FUNCTIONS GUIDE
*IF EQUIPPED
DRIVER'S PANEL

9
Blind Spot Detection (BSD) System*
The BSD System uses radar sensors to help alert the driver before changing
lanes The BSD System is ON when the button A is pressed – the button light
will illuminate The outside rearview mirror warning lights will also illuminate for
3 seconds
The system will become active when the vehicle is traveling more than 9 mph
and will alert the driver if another vehicle is detected by the radar sensor
Blind Spot Detection / Lane Change Assist
1st-stage alert: When another vehicle is detected within the BSD System
boundary
B, a yellow indicator will illuminate on the outside rearview mirrors
2nd-stage alert: When 1st-stage alert is on and the driver activates a turn
signal, a flashing yellow indicator will illuminate on the outside rearview mirrors
and the system will sound an alert
RCTA (Rear Cross Traffic Alert)
If the RCTA system sensors detect approaching vehicles from the left or right
side
C, the system will sound an audible alert, the warning indicators on the
outside rearview mirror will illuminate and a message will appear on the LCD
screen, when these conditions are met:
• When the gear shift is in Reverse
• When the vehicles moves in reverse
• When the vehicle is moving less than 6 mph
REMINDERS:

• When the BSD System is ON and the ignition is cycled to OFF then ON again, the BSD System
returns to ON

•The RCTA feature can be turned OFF/ON in User Settings and will remain in OFF/ON as selected
For more information on the Blind Spot Detection System, please refer to the Owner’s Manual.


Blind Spot Detection
System w/RCTA Video

To view a video on your
mobile device, snap this
QR Code or visit the listed
website
Refer to page 2 for more
information QR CODE
www. KuTechVideo s.c om/vg13/2016
A
B
C
ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS. *IF EQUIPPED
DRIVER'S PANEL

10


Lane Departure
Warning Video

To view a video on your
mobile device, snap this
QR Code or visit the listed
website
Refer to page 2 for more
information QR CODE
www. KuTechVideo s.c om/vg13/2016
Lane Departure Warning System (LDWS)*
With the ENGINE START/STOP button in the ON position, press
the LDWS button C to turn system ON The instrument cluster
indicator
will illuminate green LDWS will stay on when the
ignition is cycled
If the LDWS detects that you are veering outside of your lane,
the system may issue a warning on the LCD screen and an alert
may sound, under these conditions:
• The vehicle exceeds approximately 43 mph

• The LDWS system recognizes the lane the vehicle is
traveling in
REMINDER: LDWS will not issue a warning if the turn signal is activated
The Lane Departure Warning System (LDWS) is not a substitute for safe and
proper driving. Always drive safely and use caution. LDWS may not always alert
the driver if the vehicle is driven outside of it’s lane.
ODO 123456 mi
LDWS
ODO 123456 mi
LDWS
ODO 123456 mi
LDWS
ODO 123456 mi
LDWS
ODO 123456 mi
LDWS
ODO 123456 mi
LDWS
ODO 123456 mi
LDWS
ODO 123456 mi
LDWS
ODO 123456 mi
LDWS
ODO 123456 mi
LDWS
ODO 123456 mi
LDWS
ODO 123456 mi
LDWS
ODO 123456 mi
LDWS
ODO 123456 mi
LDWS
ODO 123456 mi
LDWS
ODO 123456 mi
LDWS
Instrument Panel Dimmer
With parking lights/headlights ON, press button D (+) or (-)
to adjust the brightness of the instrument panel illumination

REMINDER: The Instrument Panel Dimmer does not adjust brightness on the
Navigation System screen, use Navigation setup to adjust brightness on the
Navigation System
(Button panel located left of Steering Wheel)
D
C
When the LDWS sensor detects
the lane traveling inWhen the LDWS sensor does not
detect the lane traveling in
When the LDWS sensor detects the vehicle veering outside of the lane traveling
in, a yellow indicator will illuminate
CADENZA FEATURES & FUNCTIONS GUIDE
*IF EQUIPPED
DRIVER'S PANEL

20
CANCELCRUISE
RES
SET
VOL
VOL
MUTE
MODE
CANCELCRUISE
RES
SET
VOL
VOL
MUTE
MODE
CANCELCRUISE
RES
SET
VOL
VOL
MUTEMODE
CANCELCRUISE
RES
SET
VOL
VOL
MUTEMODE
Advanced Smart Cruise Control (ASCC)*
The Advanced Smart Cruise Control (ASCC)* system allows you to set the
vehicle to maintain a speed so long as it is not limited by traffic When traffic is
encountered, the vehicle will be slowed to maintain a set distance behind traffic
without depressing the accelerator or brake pedal
To set/adjust the ASCC speed:
• Push the CRUISE button
A to turn system ON The CRUISE indicator will
illuminate on the instrument cluster
• Accelerate/decelerate to the desired speed
• Move the ASCC lever
B to set or adjust speed
To set the vehicle-to-vehicle distance, press the ASCC button
C on the
steering wheel The images on the LCD screen D and the Instrument
Cluster E will change when scrolling through the
settings Each time the button C is pressed, the
vehicle-to-vehicle distance changes
To turn system OFF, press the CRUISE button
A The CRUISE indicator on the
instrument cluster will turn OFF and the LCD screen ASCC image will show
cancelled
F
REMINDERS:

•Cruise Control button must be ON in order to turn ASCC ON/OFF

• ASCC system is activated when ignition is turned on Speed will need to be reset when
ignition is cycled on

• The distance settings are approximations and may vary depending on factory settings at the
time See owner’s manual for more information
SET 27MPH
(Buttons located on right side of Steering Wheel)


Advanced Smart Cruise
Control Video

To view a video on your
mobile device, snap this
QR Code or visit the listed
website
Refer to page 2 for more
information QR CODE
www. KuTechVideo s.c om/vg13/2016


To change the Cruise Control mode from ASCC to standard Cruise Control, press and
hold button
C Repeat to switch modes again ( The ASCC system must not be activated
to change modes)
For the ASCC System to operate:

•When no vehicle is in front, you must be travelling at a minimum speed of 19 mph
•When following a vehicle, there is no minimum speed requirement
When following a vehicle, the system will automatically adjust your cruise speed based
on the vehicle in front It will even bring the vehicle to a complete stop if necessary
QUICK TIPS
A
B
C
E
DF
17 2 f t13 0 f t
82ft 98ft
CADENZA FEATURES & FUNCTIONS GUIDE
*IF EQUIPPED
STEERING WHEEL CONTROLS

21
Your vehicle’s steering wheel buttons may differ from those in the illustrations. See your Owner’s
Manual for more details.
Audio Controls* Cruise Control*
E CRUISE Control ON/OFF button: Press to turn the Cruise Control
ON/OFF
F Resume Cruising Speed button: Press to resume or increase
cruising speed
G Set Cruising Speed button: Press to set or decrease Cruising Speed
H Cruise Control CANCEL button: To cancel Cruise Control setting, do
one of the following:

• Press the brake pedal

• Press the CANCEL button
A Audio Mode button: Press to cycle through FM 1-2/AM/Sirius® 1-3 /
USB/iPod®/Aux / Bluetooth® Audio Streaming/My Music modes
B Seek/Preset button:
FM/AM/Sirius® Modes: Press to advance through Preset Stations
Press and hold to auto seek

Media Modes: Press to move Track Up/Down Press and hold to Fast
Forward / Rewind
C Volume button: Press up/down to raise/lower volume
D MUTE button: Press to mute all audio
Driving while distracted is dangerous and should be avoided. Drivers should remain attentive to
driving and always exercise caution when using the steering-wheel-mounted controls while driving.
CANCELCRUISE
RES
SET
VOL
VOL
MUTEMODE
CANCELCRUISE
RES
SET
VOL
VOL
MUTEMODE
CANCELCRUISERES
SETVOLVOL
MUTEMODE
CANCELCRUISERES
SETVOLVOL
MUTEMODE
CANCELCRUISERES
SET
VOL
VOL
MUTEMODE
CANCELCRUISERES
SET
VOL
VOL
MUTEMODE
CANCELCRUISERES
SETVOLVOL
MUTEMODE
CANCELCRUISERES
SET
VOL
VOL
MUTEMODE
CANCELCRUISERES
SET
VOL
VOL
MUTEMODE
CANCELCRUISERES
SETVOLVOL
MUTEMODE


Pressing the Audio Mode button for more than 1 second will turn Audio Mode ON/OFF QUICK TIP

•Cruise Control is designed to function above 25 mph
•The Cruise Control system will not activate until the brake pedal has been
depressed at least once after ignition ON or engine start
QUICK TIPS
AD
CB
E
H
F
G
ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS. *IF EQUIPPED
STEERING WHEEL CONTROLS

27
Auto-Hold*
Auto-Hold temporarily maintains the vehicle
at a standstill even if the brake pedal is
released Auto-Hold can be turned ON/OFF
using the AUTO HOLD switch
B on the
driver’s panel Before Auto-Hold will operate,
the driver’s door, engine hood and trunk
must be closed, and the driver’s seat belt
must be fastened
The Auto-Hold indicator has four states:
White: Standby - With vehicle at a standstill,
and AUTO HOLD switch
B turned ON, the
indicator will illuminate white While driving
the vehicle (vehicle is not at a standstill), the
Auto-Hold indicator will remain white
Green: Engaged - When coming to a
complete stop by depressing the brake
pedal, the Auto-Hold indicator changes from
white to green
OFF (not illuminated) - The indicator will turn OFF when the AUTO HOLD
switch
B is manually turned OFF or when the EPB is manually turned ON
Yellow: Malfunction - When the indicator is illuminated yellow, there may
be a system malfunction Take your vehicle to a local Kia dealer
Refer to page 4 for location of Instrument Cluster indicators.

Electric Parking Brake*
The Electric Parking Brake (EPB) system utilizes
an electric motor to engage the parking brake
Applying the Parking Brake
Depress the brake pedal and pull up the EPB
switch
A Ensure that the indicator light is
illuminated on the instrument cluster
Releasing the Parking Brake
The EPB will automatically release when the shifter
is placed in Reverse or Drive
To release EPB manually, depress the brake pedal, then press the EPB
switch
A, with the ignition switch in the ON position Ensure that the
indicator light
i s O F F
REMINDERS:

• As a bulb check, the EPB malfunction indicator will illuminate for approximately 3 seconds
when the ignition switch is turned ON

• If the warning light does not illuminate temporarily, or continues to remain lit, take your
vehicle to an authorized Kia dealer and have the system checked

• The EPB should not be operated while the vehicle is moving, unless there is an
emergency situation

• A click or electric brake motor sound may be heard while operating or releasing the EPB,
but these conditions are normal and indicate that the EPB is functioning properly


Electric Parking
Brake Video

To view a video on your
mobile device, snap this
QR Code or visit the listed
website
Refer to page 2 for more
information QR CODE
www. KuTechVideo s.c om/vg13/2016
(Buttons located below Gear Shift)


•When leaving your keys with parking lot attendants or valet, make sure to inform
them how to operate the EPB

•If parked on a steep incline, pull up the EPB switch for more than 3 seconds for a
firmer EPB application

•Pull up and hold EPB switch again to increase brake pressure if parked on a
decline or incline
QUICK TIPS
A
B
ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS. *IF EQUIPPED
CENTER PANEL

28
Heated Steering Wheel*
Press Heated Steering Wheel button A to turn ON/OFF Steering Wheel
Heater, while the ENGINE START/STOP button is in the ON position Steering
Wheel Heater will turn off automatically in 30 minutes, or when button is
pressed again to deactivate
Power Rear Sunshade*
Press the Power Rear Sunshade button B to raise/lower sunshade, while
the ENGINE START/STOP button is in the ACC/ON position
(Buttons located below Gear Shift)


•If ignition is turned OFF, then ON again within 30 minutes of Steering Wheel
Heater being turned ON, the system will remain in the ON position

•System does NOT turn off when ignition is cycled To turn off system, press the
Heated Steering Wheel button
QUICK TIPS


1 The Power Rear Sunshade will lower when the Gear Shift is moved into the R
(Reverse) position
2 Then when the Gear Shift is moved into D (Drive) and vehicle’s traveling more
than 12 mph, the Power Rear Sunshade will unfold automaticallyQUICK TIPS
A
B
CADENZA FEATURES & FUNCTIONS GUIDE
*IF EQUIPPED
CENTER PANEL

29


Seat Warmers and
Ventilated Seats Video

To view a video on your
mobile device, snap this
QR Code or visit the listed
website
Refer to page 2 for more
information QR CODE
www. KuTechVideo s.c om/vg13/2016
(Buttons located below Gear Shift)
(Buttons located below Gear Shift)
Seat Warmers / Ventilated Seats*
Seat Warmers
• Press right side of button once for high setting
(3 LEDs lit)

• Press button twice for medium setting (2 LEDs lit)

• Press a third time for low setting (1 LED lit) and
again to turn OFF
Ventilated Seats
• Press left side of button once for high setting
(3 LEDs lit)

• Press twice for medium setting (2 LEDs lit)

• Press a third time for low setting (1 LED lit) and
again to turn OFF
Warming ( Yellow LED)
Ventilating (Blue LED)
Seat Warmers / Ventilated Seats*
Seat Warmers only*

• Press button once for high setting (2 LEDs lit)

• Press button twice for low setting (1 LED lit)

• Press button a third time to turn OFF

•With the seat warmer switch in the ON position, the heating
system in the seat turns OFF or ON automatically depending
on the seat temperature

•System turns OFF when ignition is cycled To turn system ON
again, press the Heated Steering Wheel button
QUICK TIPS
ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS. *IF EQUIPPED
CENTER PANEL

34
Map/Room Lamps
Automatic turn off function*
The interior lights automatically turn off approximately 30 seconds after the ENGINE
START/STOP button is OFF
Map/Room Lamp Operation
Press the buttons
A to turn the Map Lamps ON/OFF This light produces a spot
beam for convenient use as a map lamp or as a personal lamp for the driver or the
front passenger
Room Lamp - Press the lens
B to turn the Room Lamp ON/OFF
The Map and Room Lamps turn ON when button
C is pressed any door is opened
or the ignition is turned OFF When all doors are locked or the ignition is ON, the Map
Lamp will turn OFF immediately The Map and Room Lamps turn ON for approximately
30 seconds
REMINDER: When Room Lamp lens is pressed ON it will remain ON, even when the Map Lamp switch is in the
OFF position


•When doors are unlocked by the Smart Key*, the lamp turns ON for approximately 30 seconds
•If your vehicle is equipped with the theft alarm system, the interior lights automatically turn off
approximately 3 seconds after the system is in armed stage

•Using interior lights for an extended period of time may cause battery discharge
QUICK TIPS
AA
A
BC
CADENZA FEATURES & FUNCTIONS GUIDE
*IF EQUIPPED
OTHER KEY FEATURES

35
Sunvisor
Use the Sunvisor to shield direct light through the front or side
windows Slide the Sunvisor out and adjust as needed
REMINDERS:

•Sunvisor may not shield all direct light

•The Sunvisor may impair visibility if not adjusted properly

• Be aware of seating position when adjusting or swinging Sunvisor around to or from
the front or side windows
Panoramic Sunroof Operation*
The Sunroof and Sunshade operation is controlled through a multidirectional
switch/lever A The ignition needs to be in the ON position to operate the
sunroof/sunshade
Slide the Sunshade and Sunroof:
• Auto Open: Slide lever backward to the farthest position and release
• Auto Close: Slide the lever forward to the farthest position and release
Slide the Sunshade:
• Auto Open: Slide the lever partially backward to the first detent position
• Auto Close: Slide the lever forward to the farthest position
Slide the Sunroof (with Sunshade open):
• Open: Slide the lever backward and release
• Auto Close: Slide the lever forward to the first detent position or pull the
lever downward
Tilt the Sunroof:
• Raise: Push lever upward
• Lower: Pull lever downward
• Auto Close Sunroof and Sunshade: Slide the lever forward to the
farthest position
REMINDER: Sunshade needs to remain OPEN while Sunroof is open and vehicle is moving


To stop the Sunroof/Sunshade at any position, push or pull the Sunroof control lever
in any direction QUICK TIP
A
ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS. *IF EQUIPPED
OTHER KEY FEATURES