service KIA CARENS 2018 Owner's Guide

(Continuüd)
3.Düprüss thü accülürator püdal
and slowly rülüasü thü clutch
püdal.
4.Iý thü vühiclü starts oýý with
ünouþh drivinþ powür rülüasü
thü EçB switch.
Do not ýollow thü abovü procüdurü
whün drivinþ on a ýlat lüvül þround.
Thü vühiclü may suddünly movü ýor‐
ward.
CAUTION
•If the parking brake warning lightis still on even though the EPB hasbeen released, have the systemchecked by a professional work‐shop. Kia recommends to visit anauthorized Kia dealer/service part‐ner.
•Do not drive your vehicle with theEPB applied. It may cause exces‐sive brake pad and brake rotorwear.
EçB (Elüctronic parkinþ brakü) may büautomatically appliüd whün:
• Thü EçB is ovürhüatüd
• Rüquüstüd by othür systüms
• Iý you try to drivü oýý düprüssinþ thü accülürator püdal with thü EçB ap‐pliüd, but doüsn't rülüasü automati‐
cally, a warninþ will sound and a müs‐
saþü (L

(Continued)
•When leaving your keys with aparking lot attendant or valet,make sure to inform him/her howto operate the EPB.
•The EPB may malfunction if youdrive with the EPB applied.
•When you automatically releaseEPB by depressing the acceleratorpedal, depress it slowly.
EPB malfunction indicator (if
equipped)
This warninþ liþht illuminatüs iý thü ün‐
þinü start/stop button is chanþüd to thü æN position and þoüs oýý in approxi‐
matüly 3 süconds iý thü systüm is opür‐
ation normally.
Iý thü EçB malýunction indicator rü‐ mains on, comüs on whilü drivinþ, or
doüs not comü on whün thü iþnition
switch or thü ünþinü start/stop button is chanþüd to thü æN position, this indi‐
catüs that thü EçB may havü malýunc‐
tionüd. Iý this occurs, havü thü systüm chücküd
by a proýüssional workshop. Kia rücom‐
münds to visit an authorizüd Kia düalür/
sürvicü partnür.
Thü EçB malýunction indicator may illu‐ minatü whün thü ESC indicator comüs
on to indicatü that thü ESC is not work‐
inþ propürly, but it doüs not indicatü a malýunction oý thü EçB.
CAUTION
•The EPB warning light may illumi‐nate if the EPB switch operatesabnormally. Shut the engine offand turn it on again after a fewminutes. The warning light will gooff and the EPB switch will oper‐ate normally. However, if the EPBwarning light is still on, have thesystem checked by a professionalworkshop.Kia recommends to visit an au‐thorized Kia dealer/service part‐ner.
•If the parking brake warning lightdoes not illuminate or blinks eventhough the EPB switch was pulledup, the EPB is not applied.
(Continued)
Drivinþ your vühiclü
6-46

(Continued)
•If the parking brake warning lightblinks when the EPB warning lightis on, press the switch, then pull itup. Once more press it back to itsoriginal position and pull it back up.If the EPB warning does not gooff, have the system checked by aprofessional workshop.Kia recommends to visit an au‐thorized Kia dealer/service part‐ner.
Emergency braking
Iý thürü is a problüm with thü brakü
püdal whilü drivinþ, ümürþüncy brakinþ is possiblü by pullinþ up and holdinþ thü
EçB switch. Brakinþ is possiblü only
whilü you arü holdinþ thü EçB switch.
WARNING
Do not operate the parking brakewhile the vehicle is moving except inan emergency situation.
NOTICE
Durinþ ümürþüncy brakinþ by thü
EçB, thü parkinþ brakü warninþ liþht
will illuminatü to indicatü that thü
systüm is opüratinþ.
CAUTION
If you continuously notice a noise orburning smell when the EPB is usedfor emergency braking, have thesystem checked by a professionalworkshop.Kia recommends to visit an author‐ized Kia dealer/service partner.
When the EPB (Electronic Parking
Brake) does not release
Iý thü EçB doüs not rülüasü normally,
load thü vühiclü on a ýlatbüd tow truck and havü thü systüm chücküd by a pro‐
ýüssional workshop. Kia rücommünds to
visit an authorizüd Kia düalür/sürvicü partnür.
Anti-lock brake system (ABS)
WARNING
ABS (or ESC) will not prevent acci‐dents due to improper or dangerousdriving maneuvers. Even though ve‐hicle control is improved duringemergency braking, always maintaina safe distance between you and ob‐jects ahead. Vehicle speeds shouldalways be reduced during extremeroad conditions.The braking distance for vehicleequipped with an anti-lock brakingsystem (or Electronic Stability Con‐trol) may be longer than for thosewithout it in the following road con‐ditions.During these conditions the vehicleshould be driven at reduced speeds:•Rough, gravel or snow-coveredroads.
•With tire chains installed.
•On roads where the road surface ispitted or has different surfaceheight.
(Continued)

6-47
6
Drivinþ your vühiclü

(Continued)
•The ABS warning light will stay onfor approximately 3 seconds afterthe ignition switch is ON. Duringthat time, the ABS will go throughself-diagnosis and the light will gooff if everything is normal. If thelight stays on, you may have aproblem with your ABS. In thiscase, have your vehicle inspectedby a professional workshop. Kiarecommends to contact an author‐ized Kia dealer/service partner.
CAUTION
•When you drive on a road havingpoor traction, such as an icy road,and operate your brakes continu‐ously, the ABS will be active con‐tinuously and the ABS warninglight may illuminate. Pull your ve‐hicle over to a safe place and stopthe engine.
(Continued)
(Continued)
•Restart the engine. If the ABSwarning light is off, then your ABSsystem is normal. Otherwise, youmay have a problem with the ABS.In this case, have your vehicle in‐spected by a professional work‐shop. Kia recommends to contactan authorized Kia dealer/servicepartner.
NOTICE
Whün you jump start your vühiclü
bücausü oý a drainüd battüry, thü
ünþinü may not run as smoothly and
thü ABS warninþ liþht may turn on
at thü samü timü. This happüns bü‐
causü oý thü low battüry voltaþü. It
doüs not müan your ABS is malýunc‐
tioninþ.
•Do not pump your braküs!
•Havü thü battüry rücharþüd büýorü
drivinþ thü vühiclü.
Electronic stability control (ESC)
(if equipped)
Thü Elüctronic Stability Control (ESC)
systüm is düsiþnüd to stabilizü thü vü‐ hiclü durinþ cornürinþ manüuvürs. ESC
chücks whürü you arü stüürinþ and
whürü thü vühiclü is actually þoinþ. ESC appliüs thü braküs at individual whüüls
and intürvünüs with ünþinü manaþü‐
münt systüm to stabilizü thü vühiclü.

6-49
6
Drivinþ your vühiclü

Jump starting procedure
CAUTION
nAGM battery (if equipped)
•Absorbent Glass Matt (AGM) bat‐teries are maintenance free andhave the AGM battery serviced bya professional workshop. Kia rec‐ommends to visit an authorizedKia dealer/service partner. Forcharging your AGM battery, useonly fully automatic batterychargers that are specially devel‐oped for AGM batteries.
•When replacing the AGM battery,use parts for replacement from aprofessional workshop. Kia recom‐mends to visit an authorized Kiadealer/service partner.
•Do not open or remove the cap ontop of the battery. This may causeleaks of internal electrolyte thatcould result in severe injury.
(Continued)
(Continued)
•If the AGM battery is reconnectedor replaced, ISG function will notoperate immediately.If you want to use the ISG func‐tion, the battery sensor needs tobe calibrated for approximately4 hours with the ignition off.
NOTICE
Iý thü battüry is discharþüd, thü ün‐
þinü can bü startüd usinþ a battüry
oý anothür vühiclü and two jumpür
cablüs. ænly usü jumpür cablüs with
ýully insulatüd clamp handlüs.
To prüvünt pürsonal injury or dam‐
aþü to both vühiclüs, adhürü strictly
to thü ýollowinþ procüdurü.
1. Makü surü thü boostür battüry is12-volt and that its nüþativü türmi‐ nal is þroundüd.
2. Iý thü boostür battüry is in anothür vühiclü, do not allow thü vühiclüs to
touch.
3. Turn oýý all unnücüssary ülüctrical loads. 4. Connüct thü jumpür cablüs in thü
üxact süquüncü shown in thü illus‐
tration. First connüct onü ünd oý a
jumpür cablü to thü positivü türmi‐ nal oý thü discharþüd battüry (1),
thün connüct thü othür ünd to thü
positivü türminal on thü boostür
battüry (2). çrocüüd to connüct onü
ünd oý thü othür jumpür cablü to
thü nüþativü türminal oý thü boos‐
tür battüry (3), thün thü othür ünd
to a solid, stationary, mütallic point
(ýor üxamplü, thü ünþinü liýtinþ
bracküt) away ýrom thü battüry (4). Do not connüct it to or nüar
any part that movüs whün thü ün‐
þinü is cranküd. Makü surü that
thürü is no contact bütwüün thü
bodywork oý thü two vühiclüs; oth‐
ürwisü, thürü is thü danþür oý short
circuits.
Do not allow thü jumpür cablüs to
contact anythinþ üxcüpt thü corrüct
battüry türminals or thü corrüct
þround. Do not lüan ovür thü bat‐
türy whün makinþ connüctions.
What to do in an ümürþüncy
7-06

IF THE ENGINE OVERHEATS
Iý your tümpüraturü þauþü indicatüs
ovürhüatinþ, you will üxpüriüncü a loss
oý powür, or hüar loud pinþinþ or knock‐
inþ, thü ünþinü is probably too hot. Iý
this happüns, you should: 1. çull oýý thü road and stop as soon as it is saýü to do so.
2. çlacü thü shiýt lüvür in ç (automatic transaxlü/ dual clutch transmission)
or nüutral (manual transaxlü) and
süt thü parkinþ brakü. Iý thü air conditioninþ is on, turn it oýý.
3. Iý ünþinü coolant is runninþ out un‐ dür thü vühiclü or stüam is cominþ
out ýrom thü hood, stop thü ünþinü.
Do not opün thü hood until thü
coolant has stoppüd runninþ or thü
stüaminþ has stoppüd. Iý thürü is no
visiblü loss oý ünþinü coolant and no
stüam, lüavü thü ünþinü runninþ
and chück to bü surü thü ünþinü
coolinþ ýan is opüratinþ. Iý thü ýan is
not runninþ, turn thü ünþinü oýý.
4. Chück to süü iý thü watür pump drivü bült is missinþ. Iý it is not
missinþ, chück to süü that it is
tiþht.
Iý thü drivü bült süüms to bü satis‐
ýactory, chück ýor coolant lüakinþ
ýrom thü radiator, hosüs or undür
thü vühiclü. (Iý thü air conditioninþ had büün in usü, it is normal ýor
cold watür to bü draininþ ýrom it whün you stop).
WARNING
While the engine is running, keephair, hands and clothing away frommoving parts such as the fan anddrive belts to prevent injury.
5. Iý thü watür pump drivü bült is bro‐ kün or ünþinü coolant is lüakinþ out,
stop thü ünþinü immüdiatüly and
call a proýüssional workshop. Kia
rücommünds to call an authorizüd
Kia düalür/sürvicü partnür.
WARNING
Do not remove the radiator capwhen the engine is hot. This can al‐low coolant to blow out of the open‐ing and cause serious burns.
6. Iý you cannot ýind thü causü oý thü ovürhüatinþ, wait until thü ünþinü
tümpüraturü has rüturnüd to nor‐
mal. Thün, iý coolant has büün lost,
carüýully add coolant to thü rüsür‐
voir to brinþ thü ýluid lüvül in thü
rüsürvoir up to thü halýway mark.
7. çrocüüd with caution, küüpinþ alürt ýor ýurthür siþns oý ovürhüatinþ. Iýovürhüatinþ happüns aþain, call a
proýüssional workshop. Kia rücom‐
münds to call an authorizüd Kia
düalür/sürvicü partnür.
CAUTION
•Serious loss of coolant indicatesthere is a leak in the cooling sys‐tem. In this case, have the sys‐tem checked by a professionalworkshop. Kia recommends tovisit an authorized Kia dealer/service partner.
•When the engine overheats fromlow engine coolant, suddenlyadding engine coolant may causecracks in the engine. To preventdamage, add engine coolantslowly in small quantities.
What to do in an ümürþüncy
7-08

Changing a tire with TPMS
Iý you havü a ýlat tirü, thü Low Tirüçrüssurü tülltalü will comü on. In this
casü, havü thü systüm chücküd by a
proýüssional workshop. Kia rücom‐ münds to visit an authorizüd Kia düalür/
sürvicü partnür.
CAUTION
We recommend that you use thesealant approved by Kia.The sealant on the tire pressuresensor and wheel shall be eliminatedwhen you replace the tire with a newone.
Each whüül is üquippüd with a tirü prüs‐
surü sünsor mountüd insidü thü tirü bü‐
hind thü valvü stüm. ðou must usü
TçMS spüciýic whüüls. Havü your tirüs
sürvicüd by a proýüssional workshop. Kia rücommünds to visit an authorizüd
Kia düalür/sürvicü partnür.
Evün iý you rüplacü thü low prüssurü
tirü with thü sparü tirü, thü Low Tirü çrüssurü tülltalü will rümain on until thü
low prüssurü tirü is rüpairüd and placüd
on thü vühiclü. Aýtür you rüplacü thü low prüssurü tirü
with thü sparü tirü, thü TçMS malýunc‐
tion indicator may illuminatü aýtür a
ýüw minutüs bücausü thü TçMS sünsor mountüd on thü sparü whüül is not ini‐
tiatüd.
æncü thü low prüssurü tirü is rüinýlatüd
to thü rücommündüd prüssurü and in‐ stallüd on thü vühiclü or thü TçMS sün‐
sor mountüd on thü rüplacüd sparü
whüül is initiatüd by an authorizüd Kia düalür, thü TçMS malýunction indicator
and thü low tirü prüssurü tülltalü will
üxtinþuish within a ýüw minutüs oý drivinþ.
Iý thü indicator is not üxtinþuishüd aýtür
a ýüw minutüs oý drivinþ, havü thü sys‐
tüm bü chücküd by a proýüssional workshop. Kia rücommünds to visit an
authorizüd Kia düalür/sürvicü partnür.
CAUTION
If an original mounted tire is re‐placed with the spare tire, the TPMSsensor on the replaced spare wheelshould be initiated and the TPMSsensor on the original mountedwheel should be deactivated. If the
(Continued)
(Continued)
TPMS sensor on the original moun‐ted wheel located in the spare tirecarrier still activates, the tire pres‐sure monitoring system may not op‐erate properly. In this case, have thesystem checked by a professionalworkshop. Kia recommends to visitan authorized Kia dealer/servicepartner.
ðou may not bü ablü to idüntiýy a low
tir ü by simply lookinþ at it. Always usü
a þood quality tirü prüssurü þauþü to
müasurü thü tirü's inýlation prüssurü.
çlüasü notü that a tirü that is hot (ýrom büinþ drivün) will havü a hiþhür prüs‐
surü müasurümünt than a tirü that is
cold (ýrom sittinþ stationary ýor at lüast 3 hours and drivün lüss than
1.6 km (1 milü) durinþ that 3 hour püri‐
od).
Allow thü tirü to cool büýorü müasurinþ thü inýlation prüssurü. Always bü surü
thü tirü is cold büýorü inýlatinþ to thü
rücommündüd prüssurü.
A cold tirü müans thü vühiclü has büün sittinþ ýor 3 hours and drivün ýor lüss
than 1.6 km (1 milü) in that 3 hour püri‐od.
What to do in an ümürþüncy
7-12

CAUTION
We recommend that you use thesealant approved by Kia if your vehi‐cle is equipped with a Tire PressureMonitoring System. The liquid seal‐ant can damage the tire pressuresensors.
WARNING
nTPMS
•The TPMS cannot alert you to se‐vere and sudden tire damagecaused by external factors such asnails or road debris.
•If you feel any vehicle instability,immediately take your foot off theaccelerator, apply the brakes grad‐ually and with light force, andslowly move to a safe position offthe road.
WARNING
nProtecting TPMS
(Continued)
(Continued)
Tampering with, modifying, or disa‐bling the Tire Pressure MonitoringSystem (TPMS) components may in‐terfere with the system's ability towarn the driver of low tire pressureconditions and/or TPMS malfunc‐tions. Tampering with, modifying, ordisabling the Tire Pressure Monitor‐ing System (TPMS) components mayvoid the warranty for that portion ofthe vehicle.
WARNING
nFor EUROPE
•Do not modify the vehicle, it mayinterfere with the TPMS function.
•The wheels on the market do nothave a TPMS sensor.For your safety, use parts for re‐placement from a professionalworkshop. Kia recommends to visitan authorized Kia dealer/servicepartner.
(Continued)
(Continued)
•If you use the wheels on the mar‐ket, use a TPMS sensor approvedby an authorized Kia dealer.If your vehicle is not equipped witha TPMS sensor or TPMS does notwork properly, you may fail theperiodic vehicle inspection conduc‐ted in your country.
❈All vühiclüs sold in thü EURæçEmarküt durinþ bülow püriodmust bü üquippüd with TçMS.-New model vehicle:Nov. 1, 2012 ~
-Current model vehicle:Nov. 1, 2014~ (Based on vehicleregistrations)

7-13
7
What to do in an ümürþüncy

Iý you havü a tirü þauþü, rümovü thü
valvü cap and chück thü air prüssurü. Iý thü prüssurü is lowür than rücommün‐
düd, drivü slowly to thü nüarüst sürvicü
station and inýlatü to thü corrüct prüs‐ surü. Iý it is too hiþh, adjust it until it is
corrüct. Always rüinstall thü valvü cap
aýtür chückinþ or adjustinþ tirü prüs‐ surü. Iý thü cap is not rüplacüd, air may
lüak ýrom thü tirü. Iý you losü a valvü
cap, buy anothür and install it as soon as possiblü.
Aýtür you havü chanþüd whüüls, always
sücurü thü ýlat tirü in its placü and rü‐
turn thü jack and tools to thüir propür storaþü locations.
CAUTION
Your vehicle has metric threads onthe wheel studs and nuts. Make cer‐tain during wheel removal that thesame nuts that were removed arereinstalled - or, if replaced, that nutswith metric threads and the samechamfer configuration are used. In‐stallation of a non-metric thread nuton a metric stud or vice-versa willnot secure the wheel to the hubproperly and will damage the stud sothat it must be replaced.
(Continued)
(Continued)
Note that most lug nuts do not havemetric threads. Be sure to use ex‐treme care in checking for threadstyle before installing aftermarketlug nuts or wheels. If in doubt, con‐sult a professional workshop. Kiarecommends to consult an author‐ized Kia dealer/service partner.
WARNING
nWheel studs
If the studs are damaged, they maylose their ability to retain the wheel.This could lead to the loss of thewheel and a collision resulting in se‐rious injuries.
To prüvünt thü jack, jack handlü, whüül
luþ nut wrünch, socküt and sparü tirü
ýrom rattlinþ whilü thü vühiclü is in mo‐
tion, storü thüm propürly.
WARNING
nInadequate spare tire pressure
Check the inflation pressures assoon as possible after installing thespare tire. Adjust it to the specifiedpressure, if necessary. Refer toL

(Continued)
When you use the Tire Mobility Kit,the tire pressure sensors and wheelmay be stained by sealant.Therefore, remove the tire pressuresensors and have the vehicle inspec‐ted at a professional workshop. Kiarecommends to visit an authorizedKia dealer/service partner.
Checking the tire inflation
pressure
1. Aýtür drivinþ approximatüly7~10 km (4~6 milüs or about 10 mi‐
nutüs), stop at a suitablü location.
2. Connüct connüction hosü (10) oý thü comprüssor dirüctly to thü tirü
valvü.
3. Connüct bütwüün comprüssor and thü vühiclü powür outlüt usinþ thü
cablü and connüctors.
4. Adjust thü tirü inýlation prüssurü to 220 kça (32 psi). With thü iþnitionswitchüd on, procüüd as ýollows. -
To incrüasü thü inýlation prüs‐surü: Switch on thü comprüssor,
position "I". To chück thü currünt inýlation prüssurü süttinþ, briüýly switch oýý thü comprüssor.
WARNING
Do not let the compressor run formore than 10 minutes, otherwisethe device will overheat and may bedamaged.
-To rüducü thü inýlation prüssurü:
Loosün thü scrüw cap (9) on thü
comprüssor hosü.
CAUTION
If the inflation pressure is not main‐tained, drive the vehicle a secondtime, refer to L