battery KIA CARNIVAL 2007 Workshop Manual

1.Remove ( - ) negative battery terminal.
2. Remove the sliding door trim panel. (Refer to the Body group - rear door)
3. Disconnect the motor connector from the motor.
4.Connect the motor terminals directly to battery voltage and check that the motor operates smoothly. Next, reverse
the polarity and check that the motor operates smoothly in the reverse direction. If the operation is abnormal,
replace the motor.
QUARTER GLASS MOTOR INSPECTION
1.Remove ( - ) negative battery terminal.
2. Remove the D pillar trim panel (A). (Refer to the Body group - interior trim)
3. Disconnect the motor connector from the motor.
4.Connect the motor terminals directly to battery voltage and check that the motor operates smoothly. Next, reverse
the polarity and check that the motor operates smoothly in the reverse direction. If the operation is abnormal,
replace the motor.

2007 > 2.7L V6 GASOLINE >
REPLACEMENT
DRIVER/ASSIST DOOR MODULE (DDM/ADM)
1. Remove ( - ) negative battery terminal.
2. Remove the front door trim panel. (Refer to the Body group - front door)
3. Disconnect the door module mounting screws (5EA) after disconnecting the module connectors (3EA) from the
motor.
4.Remove the door module (DDM/ADM) (A) from the front door trim panel.
5.Installation is the reverse of removal.
SLIDING POWER WINDOW SWITCH
1.Remove ( - ) negative battery terminal.
2. Disconnect the connector (B) after removing the sliding power window switch (A) from the B pillar trim (C).
3.Installation is the reverse of removal.
QUARTER GLASS SWITCH

1.Remove ( - ) negative battery terminal.
2. Disconnect the connector (B) after removing the quarter glass switch (A) from the rear cargo area luggage trim.
3.Installation is the reverse of removal.

2007 > 2.7L V6 GASOLINE >
INSPECTION
1.Remove the cowl top cover.(Refer to the wiper)
2. Disconnect the windshield deicer connector (A) from the wiper motor linkage.
3.Check for continuity between the terminals of deicer lines.
4.Turn the ignition switch ON and the windshield deicer switch ON, then measure the voltage between the terminals
of harness side deicer connector.
O K: approx. Battery voltage (12V)

2007 > 2.7L V6 GASOLINE >
INSPECTION
1.Disconnect the negative ( - ) battery terminal.
2. Remove the console lower cover (A).
3.Remove the center facia panel(A) after loosening screws. Take care not to damage fixing clips.
4.Remove the windshield deicer switch from the center facia panel switch.
5.Installation is the reverse of removal.

2007 > 2.7L V6 GASOLINE >
INSPECTION
1.Disconnect the negative ( - ) battery terminal.
2. Remove the center facia panel, console lower cover and center air vent (A) after loosening screws. Take care not
to damage fixing clips.
3.Remove the center facia panel switch and air control panel (A) after loosening screws.
4.Disconnect the air control panel connector (A).
5.Installation is the reverse of removal.

Distance[in (mm)]1.57+0.19/0
(40+5/0) 1.57+0.19/0
(40+5/0)
2. Set the washer nozzle on the specified spray position.
INSPECTION
SPEED OPERATION CHECK
1. Remove the connector from the wiper motor.
2. Attach the positive (+) lead from the battery to terminal 4 and the negative ( - ) lead to terminal 1.
3. Check that the motor operates at low speed.
4. Connect the positive (+) lead from the battery to terminal 5 and the negative ( - ) lead to terminal 1.
5. Check that the motor operates at high speed.

2007 > 2.7L V6 GASOLINE >
REPLACEMENT
1.Disconnect the negative ( - ) battery terminal.
2. Remove the front bumper cover. (Refer to Body group - Front bumper)
3. Remove the washer hose, the washer motor connector (A) and washer level sensor connector (C).
4. Remove the washer reservoir after removing 2 bolts and 1 step bolt.
5.Installation is the reverse of removal.
INSPECTION
1.With the washer motor connected to the reservoir tank, fill the reservoir tank with water.
2. Connect positive (+) battery cables to terminal 2 and negative ( - ) battery cables to terminal 1 respectively.
3. Check that the motor operates normally and the washer motor runs and water sprays from the front nozzles. If they
are abnormal, replace the washer motor.

5.Installation is the reverse of removal.
INSTALLATION
1.Install the rear wiper arm and blade to the specified position.
※ Specified position : The first defogger line from bottom of the rear window.
2. Set the rear washer nozzle on the specified spray position.
INSPECTION
1.Remove the 3P connector from the rear wiper motor.
2. Connect battery positive (+) and negative ( - ) cables to terminals 2 and 1 respectively.
3. Check that the motor operates normally. Replace the motor if it operates abnormally.

2007 > 2.7L V6 GASOLINE >
INSPECTION
1.With the washer motor connected to the reservoir tank, fill the reservoir tank with water.
2. Remove the front bumper. (Refer to the Body group - Front bumper)
3. Connect positive (+) and negative ( - ) battery cables to terminals 3 and 1 respectively to see that the washer motor
runs and water is pumped.
4. Check that the motor operates normally.
Replace the motor if it operates abnormally.