light KIA Magnetis 2006 2.G Repair Manual

5-15
Erasing Programmed ButtonsTo erase the three HomeLink buttons,
press and hold the two outside buttons
until the indicator light begins to flash
(after 20 seconds). Release both buttons.
Individual buttons cannot be erased, but
can be reprogrammed.
Reprogramming a Single
HomeLink ButtonTo program a device to HomeLink using
a HomeLink button previously trained,
follow these steps:
1. Press and hold the desired HomeLink
button. Do not release until step 4 has
been completed.
2. When the indicator light begins to
flash slowly (after 20 seconds), hold
the handheld transmitter 1 to 3 inches
away from the bottom of the mirror.
3. Press and hold the transmitter button
(or, if necessary, press and "cycle,"
as described in the ‘"Gate Operator
& Canadian Programming" portion
of this text).
4. The HomeLink indicator light will
flash slowly at first, then rapidly,
indicating successful programming.
Release both buttons.
Gate Operator Programming &
Canadian ProgrammingDuring programming, your hand-held
transmitter may automatically stop
transmitting.
Continue to press and hold the
HomeLink button while you press and
repress ("cycle") your handheld
transmitter every two seconds until the
frequency signal has been learned. The
indicator light will flash slowly at first
and then rapidly upon successful
training.ACCESSORIESFor more information on HomeLink and
HomeLink-compatible products, or to
purchase HomeLink accessories, call
1.800.355.3515 or visit
www.homelink.com.
MMSA5005
Flashing
MS-CNA-Eng 5 New.qxd 7/25/2005 5:21 PM Page 15

ROAD WARNINGHAZARD WARNING FLASHERThe hazard warning flasher serves as a
warning to other drivers to exercise
extreme caution when approaching,
overtaking, or passing your vehicle. It
should be used whenever emergency
repairs are being made or when the vehicle
is stopped near the edge of a roadway.Depress the flasher switch with the
ignition switch in any position.
All turn signal lights will flash
simultaneously.
• The hazard warning flasher will
operate whether your vehicle is
running or not.
 The turn signals do not operate when
the hazard flasher is on.
 Care must be taken when using the
hazard warning flasher while the
vehicle is being towed. Local
regulations may prohibit using it in
this manner.
OVERHEATINGIf your temperature gauge indicates
overheating, if you experience a loss of
power, or if you hear a loud knocking or
pinging noise, the engine has probably
overheated. You should follow these
procedures if you experience any of
these symptoms.
1. Turn the hazard warning flasher on,
then drive to the nearest safe location
and stop your vehicle; set the
automatic transaxle in P (Park), or
shift the manual transaxle to neutral
and apply the parking brake.
2. Make sure the air conditioner is off.
3. If coolant or steam is boiling out of
the radiator, stop the engine, then
turn the ignition switch to the ON
position. Do not restart the engine.
The radiator cooling fan will
automatically operate with the
ignition switch in the ON position. If
the cooling fan does not operate, call
an Authorized Kia Dealer for
IN CASE OF EMERGENCY
6-2
MMSA6001
MS-CNA-Eng 6.QXD 7/25/2005 5:13 PM Page 2

4. Turn off all unnecessary electrical
loads.
5. Connect the jumper cables in the exact
sequence shown in the illustration on
the previous page.
First, connect one end of a jumper
cable to the positive terminal (+) of
the discharged battery , then the
other end of the same cable to the
positive terminal (+) on the booster
battery, . Next, connect one end of
the other jumper cable to the negative
terminal (-) of the booster battery ,
then the other end to a solid,
stationary, metallic point (for
example, the engine lifting bracket) 
away from the battery. Do not connect
the jumper cable to or near any part
that moves when the engine is
cranked. Do not connect the jumper
cable from the negative terminal (-) of
the booster battery to the negative
terminal (-) of the discharged battery.Do not allow the jumper cables to
contact anything except the correct
battery terminals or the correct
ground. Do not lean over the battery
when making connections.
6. Start the engine of the vehicle with
the booster battery and run it at 2,000
rpm. Then, start the engine of the
vehicle with the discharged battery.
If the cause of your battery discharging
is not apparent (for example, having left
the lights on accidentally), you should
have your vehicle checked by an
Authorized Kia Dealer.
PUSH-STARTINGA vehicle equipped with an automatic
transaxle cannot be started by pushing. A
vehicle equipped with a manual transaxle
should not be push-started because it
could damage the emission control
system. Follow the directions for jump
starting.
IN CASE OF EMERGENCY
6-6
CAUTION
Never tow a vehicle to start it. A
sudden surge forward when the
engine starts could cause a collision
with the tow vehicle.
MS-CNA-Eng 6.QXD 7/25/2005 5:13 PM Page 6

ELECTRICAL CIRCUIT
PROTECTIONFUSESA vehicle’s electrical system is protected
from electrical overload damage by fuses.
This vehicle has two fuse panels, one
located in the driver’s side kick panel, the
other in the engine compartment near the
battery. A fuse panel chart is provided
later in this section.If any of your vehicle’s lights,
accessories, or controls do not work,
check the appropriate circuit fuse. If a
fuse has blown, the element inside the
fuse will be melted. Always replace a
blown fuse with one of the same rating.
If the replacement fuse blows out, this
indicates an electrical problem. Avoid
using the system involved and
immediately consult an Authorized Kia
Dealer.
Two kinds of fuses are used: standard for
lower amperage rating, and main for
higher amperage ratings.
FUSE REPLACEMENTIf the electrical system does not work,
first check the driver’s side fuse panel.
6-7
MMSA6003
Standard
Main fuse
Nomal Blown Nomal Blown
WARNING - Fuse
Replacement
 Never replace a fuse with
anything but another fuse of
the same type and rating.
 A higher capacity fuse could
cause damage and possibly
a fire.
 Never install a wire in place
of the proper fuse - even as a
temporary repair. It may
cause extensive wiring
damage and possibly a fire.
 Do not use a screwdriver or
any other metal object to
remove fuses because it may
cause a short circuit and
damage the system.
MS-CNA-Eng 6.QXD 7/25/2005 5:13 PM Page 7

1. Turn the ignition switch and all other
switches off.
2. Pull the suspected fuse straight out.
Use the removal tool provided on the
main fuse box in the engine
compartment. Refer to the fuse panel
chart on the fuse panel cover to
identify the likely problem fuse or
electrical circuit.
3. Check the removed fuse; replace if it
is blown.
Four (4) spare fuses are provided in the
engine compartment fuse panel cover.4. Push in a new fuse of the same
rating, and make sure it fits tightly in
the clips.
If it fits loosely, consult an
Authorized Kia Dealer.
If you do not have a spare, use a fuse of
the same rating from a circuit you may
not need for operating the vehicle, such
as the radio or clock (Room) fuse.
If the headlights or other electrical
components do not work and the fuses
are OK, check the fuse box in the engine
compartment. If a fuse is blown, it must
be replaced.
1. Turn the ignition switch and all other
switches OFF.
2. Remove the fuse box cover by
turning the plastic knob located in the
cover counterclockwise until the
cover can be removed.
3. Check the fuses. If one is blown,
replace it with a new one of the same
rating.
IN CASE OF EMERGENCY
6-8
MMSA6020
MMSA6005
Fuse box
CAUTION
After checking the fuse box in the
engine compartment, please
securely install the fuse box cover.
If not, some electrical failures may
occur causing from the water.
MS-CNA-Eng 6.QXD 7/25/2005 5:13 PM Page 8

6-9
FUSE PANEL
DESCRIPTIONDRIVER’S SIDE KICK PANEL
L
P
G
MMSA6006
10ARR HTD IND
10AHAZARD
15ARR FOG
10AA/CON
10AETACS
15ADR LOCK10AT/SIG
10AA/BAG IND
10AH/LP
15ASTOP LP
15AT/LID OPEN
25AP/SEAT
(DRIVE)10AA/CON SW
15A
ACC SOCKET
15AS/HTR
15AA/BAG
10ASTART
15ASP 1
15AFRT HTD
10ATAIL (LH)
10AAUDIO
20AWIPER
10ATAIL (RH)
15AC/LIGHTER
10AEPS
10AROOM LP
SHUNT
USE THE DESIGNATED
FUSE ONLY.
25AP/SEAT
(PASS)
10AB/UP
10ACLUSTER10AD/CLOCK
15ASP 4
2MS106002A
MS-CNA-Eng 6.QXD 7/25/2005 5:13 PM Page 9

IN CASE OF EMERGENCY
6-10
DESCRIPTION FUSE RATING PROTECTED COMPARTIMENTS
RR HTD IND10A Rear window defroster, Outside rear view mirror heater
HAZARD10A Hazard light, Turn signal lights
RR FOG15A Rear fog light
A/CON10A Air conditioning system
ETACS10A ETACS, Keyless entry system, Door lock system
DR LOCK15A Power door lock
P/SEAT (DRIVE)25A Power seat
T/LID OPEN15A Remote trunk lid
STOP LP15A Stop lights
H/LP10A Head light
A/BAG IND10A Air-bag
T/SIG10A Turn signal lights
A/CON SW10A Air conditioning system
ACC SOCKET15A Power outlet
S/HTR15A Seat heater
A/BAG15A Air-bag
B/UP10A Backup lights
MS-CNA-Eng 6.QXD 7/25/2005 5:13 PM Page 10

6-11
CLUSTER10A Cluster
START10A Engine switch
SP115A Spare fuse
FRT HTD15A Window defroster
P/SEAT (PASS)25A Power Seat
SP415A Spare fuse
D/CLOCK10A Digtal clock
TAIL(LH)10A Position lights, License plate lights, Tail lights
AUDIO10A Audio
WIPER20A Wiper
ROOM LP10A Dome lights, Front door edge warning lights
TAIL(RH)10A Position lights, License plate lights, Tail lights
C/LIGHTER15A Cigar lighter
EPS10A -
MS-CNA-Eng 6.QXD 7/25/2005 5:13 PM Page 11

6-13
DESCRIPTION FUSE RATING PROTECTED COMPARTIMENTS
COND FAN20A Condenser fan
PWR WIND40A Power window
ABS 220A ABS
IGN SW-130A Ignition switch
ABS 140A ABS
IGN SW-230A Ignition switch
RAD FAN MTR30A Radiator fan motor
FUEL PUMP20A Fuel pump
HD LP LO15A Headlights (LO)
ABS10A ABS
INJECTOR10A Injector
A/C COMPR10A Air-con compressor
ATM RLY20A ATM Relay
ECU RLY30A Engine control unit relay
IG COIL20A Ignition coil
O
2SNSR15A Oxygen sensor
ECU15A Engine control unit
MS-CNA-Eng 6.QXD 7/25/2005 5:13 PM Page 13

TOWINGIf emergency towing is necessary, we
recommend having it done by an
Authorized Kia Dealer or a competent
tow-truck service. Proper lifting and
towing procedures are necessary to
prevent damage to the vehicle. State and
local laws applicable to towing vehicles
must be followed.
IN CASE OF EMERGENCY
6-14
MMSA6007A
Wheel dolly
HORN10A Horn
HEAD LP HI15A Headlights (HI)
HEAD LP WASH20A -
DRL15A DRL
FR FOG15A Front fog lights
DIODE-1- Diode 1
SPARE30A Spare fuse
SPARE20A Spare fuse
SPARE15A Spare fuse
SPARE10A Spare fuse
DIODE-2- Diode 2
BLOWER30A Blower
PWR FUSE-230A Power fuse 2
PWR AMP20A Power amp
SUNROOF15A Sunroof
TAIL LP20A Tail lights
PWR FUSE-130A Power fuse 1
ECU10A ECU
RR HTD30A Rear window defroster
MS-CNA-Eng 6.QXD 7/25/2005 5:13 PM Page 14