light KIA OPTIMA PLUG-IN HYBRID 2017 Owners Manual

Also, the EPB is applied automatically if
the Auto Hold button is on when the engine is turned off.
NOTICE
On a steep incline or when pulling a
trailer if the vehicle does not stand
still, do as follows:
1.Apply the EPB.
2.Pull up the EPB switch for more
than 3 seconds.
CAUTION
Do not operate the parking brakewhile the vehicle is moving except inan emergency situation. It coulddamage the vehicle system and en‐danger driving safety.
Releasing the parking brake
0+'
To release the EPB (Electronic ParkingBrake), press the EPB switch in the fol‐lowing condition:
• Have the engine start/stop button in the ON position.
• Depress the brake pedal.
Make sure the brake warning light goes
off.
To release EPB (Electronic ParkingBrake) automatically:
• Shift lever in P (Park) With the engine running depress thebrake pedal and shift out of P (Park)
to R (Reverse) or D (Drive).
• Shift lever in N (Neutral) With the engine running depress the
brake pedal and shift out of N (Neu‐
tral) to R (Reverse) or D (Drive). 1. Start the engine.
2. Fasten the driver's seat belt.
3. Close the driver's door, engine hood and trunk.
4. Depress the accelerator pedal while the shift lever is in R (Rear),
D (Drive) or manual mode.
Make sure the brake warning light goes
off.
NOTICE
•For your safety, you can engage
the EPB even though the engine
stop/start button is in the OFF po‐
sition, but you cannot release it.
(Continued)
Driving your vehicle
7-20

(Continued)
•For your safety, depress the brake
pedal and release the parking
brake manually with the EPB
switch when you drive downhill or
when backing up the vehicle.
CAUTION
•If the parking brake warning lightis still on even though the EPB hasbeen released, we recommendthat the system be checked by anauthorized Kia dealer.
•Do not drive your vehicle with theEPB applied. It may cause exces‐sive brake pad and brake rotorwear.
EPB (Electronic Parking Brake) may beautomatically applied when:
• The EPB is overheated
• Requested by other systems
• The hybrid system is turned off with the EPB applied
NOTICE
If the driver turns the hybrid system
off while Auto Hold is operating, EPB
will be automatically applied. Howev‐
er, if you press the EPB switch with‐
in one second after the hybrid sys‐
tem is turned off, the EPB will not
be applied.
System warning
0+'-
• If you try to drive off depressing theaccelerator pedal with the EPB ap‐
plied, but doesn't release automati‐ cally, a warning will sound and a mes‐
sage will appear.
• If the driver's seat belt is not fas‐ tened and the engine hood or trunk is
opened, a warning will sound and a
message will appear.
• If there is a problem with the vehicle, a warning may sound and a message
may appear.
If the above situation occurs, depress
the brake pedal and release EPB by pressing the EPB switch.
WARNING
•To prevent unintentional move‐ment when stopped and leavingthe vehicle, do not use the shiftlever in place of the parking brake.Set the parking brake and makesure the shift lever is securelypositioned in P (Park).
(Continued)

7-21
7
Driving your vehicle

System warning
0+'-
5ZQF
"
0+'-
5ZQF
#
If the EPB is applied while Auto Hold is
activated because of ESC (Electronic Stability Control) signal, a warning will
sound and a message will appear.
EPB malfunction indicator (if
equipped)
0+'
This warning light illuminates if the en‐
gine start/stop button is changed to the ON position and goes off in approxi‐
mately 3 seconds if the system is oper‐
ation normally. If the EPB malfunction indicator re‐
mains on, comes on while driving, or
does not come on when the ignition
switch or the engine start/stop button is changed to the ON position, this indi‐
cates that the EPB may have malfunc‐
tioned.
If this occurs, we recommend that the system be checked by an authorized
Kia dealer.
The EPB malfunction indicator may illu‐
minate when the ESC indicator comes on to indicate that the ESC is not work‐
ing properly, but it does not indicate a
malfunction of the EPB.
CAUTION
•The EPB warning light may illumi‐nate if the EPB switch operatesabnormally. Shut the engine offand turn it on again after a fewminutes. The warning light will gooff and the EPB switch will oper‐ate normally. However, if the EPBwarning light is still on, we recom‐mend that the system be checkedby an authorized Kia dealer.
(Continued)

7-23
7
Driving your vehicle

(Continued)
•If the parking brake warning lightdoes not illuminate or blinks eventhough the EPB switch was pulledup, the EPB is not applied.
•If the parking brake warning lightblinks when the EPB warning lightis on, press the switch, then pull itup. Once more press it back to itsoriginal position and pull it back up.If the EPB warning does not gooff, we recommend that the sys‐tem be checked by an authorizedKia dealer.
Emergency braking
If there is a problem with the brake
pedal while driving, emergency braking is possible by pulling up and holding the
EPB switch. Braking is possible only
while you are holding the EPB switch.
WARNING
Do not operate the parking brakewhile the vehicle is moving except inan emergency situation.
NOTICE
During emergency braking by the
EPB, the parking brake warning light
will illuminate to indicate that the
system is operating.
CAUTION
If you continuously notice a noise orburning smell when the EPB is usedfor emergency braking, we recom‐mend that the system be checkedby an authorized Kia dealer.
When the EPB (Electronic ParkingBrake) does not release
If the EPB does not release normally, we recommend that you contact an au‐
thorized Kia dealer by loading the vehi‐
cle on a flatbed tow truck and have the system checked.
AUTO HOLD (if equipped)
The Auto Hold maintains the vehicle in
a standstill even though the brake ped‐ al is not depressed after the driver
brings the vehicle to a complete stop by
depressing the brake pedal.
Set up
0+'-
1. With the driver's door, engine hood closed, fasten the driver's seat belt
or depress the brake pedal and
then press the Auto Hold button.
The white AUTO HOLD indicator will
come on and the system will be in
the standby position.
Driving your vehicle
7-24

(Continued)
-The vehicle is standing on a
steep slope
-The vehicle moved several
times
In these cases, the brake warning
light comes on, the AUTO HOLD in‐
dicator changes from green to
white, and a warning sounds and a
message will appear to inform you
that EPB has been automatically
engaged. Before driving off again,
press foot brake pedal, check the
surrounding area near your vehicle
and release parking brake manual‐
ly with the EPB switch.
•If the AUTO HOLD indicator lights
up yellow, the Auto Hold is not
working properly. We recommend
that you contact an authorized Kia
dealer.
•While operating Auto Hold, you
may hear mechanical noise. How‐
ever, it is normal operation noise.
WARNING
•Press the accelerator pedal slowlywhen you start the vehicle.
•For your safety, cancel the AutoHold when you drive downhill orback up the vehicle or park the ve‐hicle.
CAUTION
If there is a malfunction with thedriver’s door, engine hood open de‐tection system, the Auto Hold maynot work properly.We recommend that you contact anauthorized Kia dealer.
Warning messages
Parking brake automatically locked
5ZQF
"
0+'-
5ZQF
#
0+'-
When the EPB is applied from Auto
Hold, a warning will sound and a mes‐ sage will appear.
Driving your vehicle
7-26

8
CAUTION
•If the ABS warning light is on andstays on, you may have a problemwith the ABS. In this case, howev‐er, your regular brakes will worknormally.
(Continued)
(Continued)
•The ABS warning light will stay onfor approximately 3 seconds afterthe engine start/stop buttonswitch is ON. During that time, theABS will go through self-diagnosisand the light will go off if every‐thing is normal. If the light stayson, you may have a problem withyour ABS. We recommend that youcontact an authorized Kia dealer.
CAUTION
•When you drive on a road havingpoor traction, such as an icy road,and operate your brakes continu‐ously, the ABS will be active con‐tinuously and the ABS warninglight may illuminate. Pull your ve‐hicle over to a safe place and stopthe engine.
•Restart the engine. If the ABSwarning light is off, then your ABSsystem is normal. Otherwise, youmay have a problem with the ABS.We recommend that you contactan authorized Kia dealer.
NOTICE
When you jump start your vehicle
because of a drained battery, the
engine may not run as smoothly and
the ABS warning light may turn on
at the same time. This happens be‐
cause of the low battery voltage. It
does not mean your ABS is malfunc‐
tioning.
•Do not pump your brakes!
•Have the battery recharged before
driving the vehicle.

7-29
7
Driving your vehicle

ESC operation
ESC ON condition
-• When the engine start/stopbutton is turned ON, ESC
and ESC OFF indicator lights
illuminate for approximate‐
ly 3 seconds, then ESC is turned on.
• Press the ESC OFF button for at least half a second
after turning the ignition
ON to turn ESC off. (ESC
OFF indicator will illumi‐
nate). To turn the ESC on, press the ESC OFF button
(ESC OFF indicator light will
go off).
• When starting the engine, you may hear a slight tick‐
ing sound. This is the ESC
performing an automatic
system self-check and does not indicate a problem.
When operating
When the ESC is in operation, ESC indicator light blinks. • When the Electronic Stabili‐ ty Control is operating
properly, you can feel a
slight pulsation in the vehi‐
cle. This is only the effect of brake control and indi‐
cates nothing unusual.
• When moving out of the mud or slippery road, the
engine rpm (revolution per
minute) may not increase
even if you press the accel‐ erator pedal deeply. This is
to maintain the stability
and traction of the vehicle
and does not indicate a
problem.
ESC operation off
ESC OFF state
This car has 2 kinds of ESC off states.If the engine stops when ESC
is off, ESC remains off. Upon
restarting the engine, the ESCwill automatically turn on
again.

7-31
7
Driving your vehicle

0+'-
5ZQF
"
0+'-
5ZQF
#
•ESC off state 1
To cancel ESC operation, press the
ESC OFF button (ESC OFF
) shortly
(ESC OFF indicator light (ESC OFF )
illuminates). At this state, the engine
control function does not operate. It means the traction control function
does not operate. Brake control func‐
tion only operates.
5ZQF
"
0+'-
0+'-
5ZQF
#
•ESC off state 2 To cancel ESC operation, press the
ESC OFF button (ESC OFF
) for
more than 3 seconds. ESC OFF indica‐
tor light (ESC OFF
) illuminates and
ESC OFF warning chime will sound. At
this state, the engine control function
and brake control function do not op‐
erate. It means the car stability con‐ trol function does not operate any
more.
Indicator light
&4$
JOEJDBUPS
MJHIU

&4$
0''
JOEJDBUPS
MJHIU

When engine start/stop button switch
is turned to ON, the indicator light illu‐ minates, then goes off if the ESC sys‐
tem is operating normally.
Driving your vehicle
7-32

The ESC indicator light blinks whenever
ESC is operating or illuminates when ESC fails to operate.
ESC OFF indicator light comes on when
the ESC is turned off with the button.
CAUTION
Driving with varying tire or wheelsizes may cause the ESC system tomalfunction. When replacing tires,make sure they are the same size asyour original tires.
WARNING
The Electronic Stability Control sys‐tem is only a driving aid; use precau‐tions for safe driving by slowingdown on curved, snowy, or icy roads.Drive slowly and don’t attempt toaccelerate whenever the ESC indica‐tor light is blinking, or when the roadsurface is slippery.
ESC OFF usage
When driving
• ESC should be turned on for daily driving whenever possible. • To turn ESC off while driving, press
the ESC OFF button while driving on aflat road surface.
WARNING
Never press the ESC OFF buttonwhile ESC is operating (ESC indicatorlight blinks).If ESC is turned off while ESC is op‐erating, the vehicle may slip out ofcontrol.
NOTICE
•When operating the vehicle on a
dynamometer, ensure that the
ESC is turned off by pressing the
ESC OFF button for more than 3
seconds (ESC OFF light illumina‐
ted). If the ESC is left on, it may
prevent the vehicle speed from in‐
creasing, and result in false diag‐
nosis.
•Turning the ESC off does not af‐
fect ABS or brake system opera‐
tion.
Vehicle stability management
(VSM) (if equipped)
This system provides further enhance‐ments to vehicle stability and steering
responses when a vehicle is driving on a
slippery road or a vehicle detected changes in coefficient of friction be‐
tween right wheels and left wheels
when braking.
VSM operation
When the VSM is in operation, • ESC (Electronic Stability Control) ()
light will blink.
• The steering wheel may be control‐ led.
When the vehicle stability management is operating properly, you can feel a
slight pulsation in the vehicle. This is
only the effect of brake control and in‐ dicates nothing unusual.
The VSM does not operate when:
• Driving on bank road such as gradient or incline
• Driving rearward
• ESC OFF indicator light (
) remains
on the instrument cluster

7-33
7
Driving your vehicle

• EPS (Electronic Power Steering) indi‐cator light remains on the instrument
cluster
VSM operation off
If you press the ESC OFF button to turn
off the ESC, the VSM will also cancel and the ESC OFF indicator light (
) illu‐
minates.
To turn on the VSM, press the button
again. The ESC OFF indicator light goes out.
Malfunction indicator
The VSM can be deactivated even if you
don’t cancel the VSM operation by pressing the ESC OFF button. It indi‐
cates that a malfunction has been de‐
tected somewhere in the EPS (Elec‐ tronic Power Steering) system or VSM
system. If the ESC indicator light (
) or
EPS warning light remains on, we rec‐
ommend that the system be checked by an authorized Kia dealer.
NOTICE
•The VSM is designed to function
above approximately 22 km/h
(13 mph) on curves.
(Continued)
(Continued)
•The VSM is designed to function
above approximately 10 km/h
(6 mph) when a vehicle is braking
on a split-mu road. The split-mu
road is made of surfaces which
have different friction forces.
WARNING
•The Vehicle Stability Managementsystem is not a substitute for safedriving practices but a supplemen‐tary function only. It is the respon‐sibility of the driver to alwayscheck the speed and the distanceto the vehicle ahead. Always holdthe steering wheel firmly whiledriving.
•Your vehicle is designed to activateaccording to the driver’s intention,even with the VSM installed. Al‐ways follow all the normal precau‐tions for driving at safe speed forthe conditions – including driving ininclement weather and on a slip‐pery road.
(Continued)
(Continued)
•Driving with varying tire or wheelsizes may cause the VSM systemto malfunction. When replacingtires, make sure they are thesame size as your original tires.
Hill-start assist control (HAC) (if
equipped)
A vehicle has the tendency to slip back
on a steep hill when it starts to go af‐ ter stopping. The Hill-start Assist Con‐
trol (HAC) prevents the vehicle from
slipping back by operating the brakes automatically for about 1~2 seconds.
The brakes are released when the ac‐
celerator pedal is depressed or after about 1~2 seconds.
WARNING
The HAC is activated only for about1~2 seconds, so when the vehicle isstarting off always depress the ac‐celerator pedal.
Driving your vehicle
7-34