lock KIA Rio 2005 2.G Workshop Manual

Driving Tips5-10
Snow Tires
When snow tires are used, select the size and
construction specified on the Tire Pressure Label. It is
strongly recommended that snow tires be used on all
four wheels, or poor handling may result. Snow tires
should not be operated at speeds exceeding 75 mph
(120 km/h).
These tires should be inflated 4 psi (28 kPa,
0.3 kg/cm
2) above the recommended pressures shown
on the Tire Specification/Pressure Label, but inflation
should never exceed the maximum cold-tire pressure
shown on the tire sidewalls.
Do not install studded tires without first checking
local, provincial and municipal regulations for
possible restrictions against their use.
WARNING - Snow Tire Size
Snow tires should be equivalent in size and
type to the vehicle’s standard tires. Otherwise,
the safety and handling of your vehicle may be
adversely affected.
Winter Driving We recommend that you carry emergency
equipment. Some things you might include are tire
chains, a window scraper, windshield de-icer, a bag
of sand or salt, flares, a small shovel and jumper
cables.
 Make sure you have sufficient ethylene glycol
coolant in the radiator.
 Check the battery condition and cables. Cold
temperatures reduce the capacity of any battery, so it
must be in top shape to provide enough winter
starting power.
 Make sure the engine oil viscosity is suitable for
cold weather.
 Check the ignition system for loose connections and
damage.
 Use antifreeze-formulated windshield washer fluid
and make sure you have sufficient fluid for your
trip. (Do not use engine coolant antifreeze.)
 Do not use the parking brake if it might freeze. This
is most likely to happen after driving in slushy or
wet conditions and temperatures drop into the
freezing range. When parking, shift to P (Park) with
automatic transaxle, or to 1 (First) or R (Reverse)
with a manual transaxle and block the rear wheels.
RIO ENG CNA 5.qxd 7/29/05 5:07 PM Page 10

5-11
Tire Chains
Tire Chain Selection
Regulations regarding the use of tire chains vary
according to location or type of road, so always check
them before installing chains.
Use only SAE Class “S’’ tire chains. Chains must be
the proper size for the vehicle, as recommended by the
chain manufacturer.
Chain Installation
When installing chains on your tires, carefully follow
the instructions of the chain manufacturer.
The chain bands will scratch the wheel covers.
Remove the covers before installing the chains.
WARNING - Tire Chains
 The use of chains may adversely affect
vehicle handling.
 Do not exceed 50 km/h (30 mph) or the
chain manufacturer’s recommended speed
limit, whichever is lower.
 Drive carefully and avoid bumps, holes,
sharp turns and other road hazards, which
may cause the vehicle to bounce.
 Avoid sharp turns or locked-wheel braking.
 Do not attempt to use a tire chain on the
temporary spare tire because it may impair
vehicle handling and result in damage to the
vehicle and the tire.
RIO ENG CNA 5.qxd 7/29/05 5:07 PM Page 11

6-11
Engine compartment
DESCRIPTION FUSE PROTECTED
RATING COMPONENT
Engine Compartment
(ABS) 15A ABS
RR FOG 10A Rear fog light (if equipped)
(F/FOG) 15A Front fog light (if equipped)
MAIN 80A Battery is not rechargeable
IG 1 30A (It will be automatically connect
ed to the secondary fuse.) CIGAR
10A, AUDIO 10A, IG COIL 15A,
TURN LAMP 10A, A/BAG 10A,
WIPER(RR) 15A, WIPER(FRT)
15A, RELAY 10A, START 10A
BLOWER 30A Heater
COOLING 30A Cooling fan
(ABS 1) 30A ABS
COND. FAN 20A Condenser fan
HEAD-HI 15A Head lamp high
HEAD-LOW 15A Head lamp low
EMS 10A Engine sensors
INJECTOR 15A Injector, 0
2sensor
F/PUMP 10A Fuel pump
ECU 10A Engine control unit, ECAT unit,
Main relay
RELAY 10A Blower motor, Power window,
Rear window defroster, Head
lamp(Airbag equipped vehicle)
(HLLD) 10A
-
*( ):Optional
STARTWINDOW
POWERFUEL
PUMPFRONT
FOGA/CON
HEAD
LAMPCOOL.FANHORN
TNS MAIN
IG 1 BLOWER
COOL ING(ABS 1) IG 2 COND.F
( )( ) ( )
( )
( )
COND.FAN
ROOM 15A
IG COIL
(ABS)
D/LOCK
BTN
P/WIN
(ABS 2)
RR DEF
HORN
TNS
RR FOG
(HLLD)(F/FOG)
HEAD
S/ROOF
MAIN
RELAY
RELAY
ECU
F/PUMP
INJECT
EMS
HEAD
LOW
HEAD
HI 15A
15A
25A
30A
30A
30A
25A
10A
15A
10A
10A
80A15A
25A
15A
25A
10A
10A
10A
15A
10A
15A
15A
MAIN
30A 30A 30A 30A 30A 20A
* USE THE DESIGNATED FUSE AND RELAY ONLY.
* REFER TO OWNER'S MANUAL FOR FUSE AND RELAY SERVICE.
* ( ) : OPTION
RIO ENG CNA 6.qxd 7/29/05 5:15 PM Page 11

In Case Of An Emergency6-12DESCRIPTION FUSE PROTECTED
RATING COMPONENT
Engine compartment (continued)
MAIN RELAY 25A (It will be automatically connected
to the secondary fuse.)
EMS 10A, INJECTOR 15A,
F/PUMP 10A, ECU 10A
S/ROOF 15A Sunroof
HEAD 25A (It will be automatically connect
ed to the secondary fuse.)
HEAD-HI 15A, HEAD-LOW
15A, FOG LAMP(RR) 10A
IG 2 30A
TNS 15A (It will be automatically connect
ed to the secondary fuse.)
TAIL (LH) 10A, TAIL(RH) 10A
HORN 10A Horn
RR DEF 25A Rear window defroster
(ABS 2) 20A ABS
P/WIN 30A Power window
BTN 30A (It will be automatically connect
ed to the secondary fuse.)
MEMORY/ROOM 10A,
STOP 15A, HAZARD 15A
D/LOCK 25A Power door lock
IG COIL 15A Ignition coil
ROOM 15A Room LAMP, Audio,
Meterset, Warning sound
*( ): Optional
RIO ENG CNA 6.qxd 7/29/05 5:15 PM Page 12

6-17 To remove spare tire:
Remove the cover from the spare tire. Turn the tire
hold-down wing bolt counterclockwise.
Store the jack and tire in the reverse order of removal.
To prevent the jack, jack handle, and tool bag from
“rattling’’ while the vehicle is in motion, store them
properly.
Important — Use of Compact Spare Tire
Your vehicle is equipped with a compact spare tire.
This compact spare tire takes up less space than a
regular-size tire. This tire is smaller than a
conventional tire and is designed for temporary use
only.
CAUTION
 You should drive carefully when the compact
spare is in use. The compact spare should be
replaced by the proper conventional tire and
rim at the first opportunity.
 The operation of this vehicle is not
recommended with more than one compact
spare tire in use at the same time.
CAUTION
This spare tire should be used only for VERY
short distances. Compact spares should NEVER
be used for long drives or extended distances.
1S2108010A
RIO ENG CNA 6.qxd 7/29/05 5:15 PM Page 17

6-19 Changing Tires
Jacking Instructions
The jack is provided for emergency tire changing only.
Follow jacking instructions to reduce the possibility of
personal injury.Tire Replacement
1. Park on a level surface and set the parking brake
firmly.
2. Set the automatic transaxle in P (Park), or shift the
manual transaxle into R (Reverse).
3. Activate the hazard warning flasher.
4. Remove the wheel lug nut wrench, jack, jack
handle, and spare tire from the vehicle.
5. Block both the front and rear of the wheel that is
diagonally opposite the jack position.
WARNING - Changing Tires
 Never attempt vehicle repairs or a tire
change in the traffic lanes of a public road or
highway. Always move the vehicle completely
off the road and onto the shoulder before
trying to change a tire. If you cannot find a
firm, level place off the road, call a towing
service company for assistance.
 Do not exceed the maximum permissible
load of the jack: 600 kg. (1,320 lbs).
 Be sure to use the correct front or rear
jacking positions on the vehicle; never use
the bumpers or any other part of the vehicle
for jack support.
 Never allow any portion of your body to get
beneath the vehicle while using the jack.
 Do not start or run the engine while the
vehicle is supported by the jack.
AS2B06012
Flat tire
Wheel block
RIO ENG CNA 6.qxd 7/29/05 5:15 PM Page 19

In Case Of An Emergency6-206. For models with alloy wheels, remove the center
cap.
WARNING - Changing a Front
Tire
When one front wheel is lifted off the ground,
neither the automatic transaxle P (Park)
position nor the manual transaxle R (Reverse)
position will prevent the vehicle from moving
and possibly slipping off the jack, even if these
positions are properly engaged. To prevent
vehicle movements while changing a tire,
always set the parking brake fully, and always
block the wheel diagonally opposite the wheel
being changed.
7. Loosen the four lug nuts counterclockwise one turn
each, but do not remove any nut until the tire has
been raised off the ground.
3
2
4
1
1B3106002C
RIO ENG CNA 6.qxd 7/29/05 5:15 PM Page 20

6-21
8. Place the jack at the front or rear jacking position
closest to the tire you are changing. Place the jack
under the side sill at the designated location.
9. Insert the jack handle into the jack and turn it
clockwise, raising the vehicle until the tire just
clears the ground, approximately 30 mm (1.2 in.).
Before removing the lug nuts, make sure the
vehicle is stable and that there is no chance for it to
slip or move.
WARNING -Jack Location
To reduce the possibility of injury, be sure to
use only the jack provided with the vehicle and
in the correct jack position; never use any
other part of the vehicle for jack support.
1S2108008 AS2B06014
Jack handle
RIO ENG CNA 6.qxd 7/29/05 5:15 PM Page 21

In Case Of An Emergency6-22
Once the lug nuts have been tightened, lower the
vehicle fully to the ground and continue to tighten the
lug nuts until they are completely secured.
If you are unsure of the tightness of the wheel lug nuts,
have them checked at the nearest service station. The
specified tightening torque is 103 N.
m (76 ft. lb.).
CAUTION
Your vehicle has metric threads on the wheel studs
and nuts. During wheel removal, make certain
that the same nuts removed are reinstalled - or, if
replaced, that nuts with metric threads and the
same configuration are used. Installation of a non-
metric thread nut on a metric stud or vice-versa
will not secure the wheel to the hub properly and
will damage the stud so that it must be replaced.
Be sure to use extreme care in checking for thread
style before installing aftermarket lug nuts or
wheels. If in doubt, consult an Authorized Kia
Dealer. Damaged studs may result in wheel loss
and personal injury.
10. Remove the lug nuts by turning them
counterclockwise, then remove the wheel.
11. Mount the spare tire into position and tighten the
nuts by hand. Install the lug nuts with the beveled
edge inward.
12. Turn the jack handle counterclockwise and lower
the vehicle until it touches the ground. Tighten the
lug nuts firmly in an “X’’ pattern.
3
2
4
1
1B3106002B
RIO ENG CNA 6.qxd 7/29/05 5:15 PM Page 22

7-9 Chassis and Body(cont.)
I: Inspect these items and their related parts. If necessary,
Check the engine oil and coolant levels every week.
R: Replace or change.
Kilometers or Time in Months, Whichever Comes First
km 8 16 24 32 40 48 56 64 72 80 88 96 104 112 120 128Months 4 8 12 16 20 24 28 32 36 40 44 48 52 56 60 64
P
ower steering fluid & linesIIIIIIIIDriveshaft dust boots
IIIII
Seat belts, buckles & anchors
IIIIIIIIIIIIIIII
Locks, hinges & hood latchLLLLLLLLLLLLLLLL
MAINTENANCE
INTERVALS
MAINTENANCE
ITEM
x 1,000
RIO ENG CNA 7-1.qxd 7/29/05 5:16 PM Page 9