sensor KIA STINGER 2021 Features and Functions Guide

12*IF EQUIPPED†LEG AL DISCL AIMERS ON BACK INSIDE COVER
ADAS(Button located on driver’s panel, left of the steering wheel)
(Blind-spot area monitoring)
( Vehicle approaching at high speed monitoring)
Blind-Spot Collision Warning (BCW)†6
Blind-Spot Collision Warning uses rear corner radar sensors in the rear bumper
to monitor and warn the driver if it detects an approaching vehicle in the driver’s
blind spot area and before changing lanes.
The system will activate when the vehicle is traveling
more than 20 mph and will alert the driver if another
vehicle is detected by the radar sensor.
With the Engine Start /Stop button in the ON position,
press the BCW button A to turn the system ON. The
button light will illuminate. The outside rearview mirror
warning lights will also illuminate for 3 seconds.
1st-stage warning: When another vehicle is detected within the BCW warning
boundary B, a yellow indicator will illuminate on the outside rearview mirrors C.
2nd-stage warning: When 1st stage warning is on and the driver activates a
turn signal, a flashing yellow indicator will illuminate on the outside rearview
mirrors and the system will sound an alert.
REMINDERS:
§ BCW will not issue a warning if the vehicle speed is 6 mph or more above the surrounding vehicles
§ When BCW is ON and the ignition is cycled, BCW returns to its previous state
§
BCW and RCCW are supplemental systems. Do not solely rely on these systems and always pay attention the road and its conditions and drive safely.
See section 5 in the Owner’s Manual for more information.
REMINDERS:
§ The RCCA Warning sound can be adjusted in the User Settings* or the Vehicle Settings* on the audio head unit
§ When vehicle power is cycled, RCCA will remain in the previous state RCCA can be turned OFF/ON in User Settings
§ RCCA will show a warning if the approaching vehicle speed is between 2.5-22 mph within sensing range. See owner’s manual for other conditions
§ RCCA is a supplemental system. Do not solely rely on this system and always pay attention to the road and its conditions
Rear Cross-Traffic Collision Warning (RCCW)†6
If Rear Cross-Traffic Collision Warning (RCCW ) sensors detect vehicles approaching from the rear left or rear
right side D, the system will sound an audible alert, the warning indicators on the outside rearview mirror will
illuminate and a message will appear on the LCD screen. RCCA may activate the Electronic Stability Control
(ESC) to help avoid an imminent collision. RCCA may temporarily apply braking power when an approaching
vehicle is detected within a certain distance next to or behind the vehicle.
RCCW is designed to operate under these conditions:
§ When the vehicle is in Reverse
§ When the vehicle is moving less than 6 mph
A
B
See section 5 in the Owner’s Manual for more information.D
C
BLIND-SPOT COLLISION WARNING VIDEO
To view a video on your mobile device, snap this QR Code or visit the listed website. Refer to inside cover for more information.
www.youtube.com/KiaFeatureVideos
QR CODE
§ BCW will activate when:
§ The system is turned on
§ Vehicle speed is above approximately 20 mph
§ Other vehicles are detected on the rear sides of the vehicle
QUICK TIP
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)

22
STEERING WHEEL CONTROLS
STEERING WHEEL CONTROLS
MISTOFF
AUTO LOHIAUTO
Lifting Wipers (Wiper Service Mode)
To lift the windshield wipers to clean windshield, inspect or replace
wiper blades or raise wipers in snow/ice conditions without damaging
the hood, the blades need to be moved to the service position C.
With the ignition ON, turn the ignition OFF, and within 20 seconds
move the wiper switch to the MIST position B and hold the switch for
more than two seconds until the wiper blade is in the fully up position.
To return wipers to normal position, turn the ignition ON, then activate MIST.
A
B
See section 4 in the Owner’s Manual for more information.
Windshield Wipers & Washers
To operate:
§ Move lever up/down to change wiper modes
M I S T: Single wipe
OFF: Wiper off
AUTO: Auto Rain Sensing
LO: Slow wipe
HI: Fast wipe
§ Pull to spray and wipe
Auto Rain Sensing*
The rain sensor located on the upper end of the windshield glass is designed
to sense the amount of rainfall and control the wiping cycle for the proper
interval. The more it rains, the faster the wiper operates. When the rain stops,
the wiper stops.
To turn ON the auto rain sensing wipers, move lever up/down to AUTO.
To adjust the auto rain sensing wiper speed setting, move the speed control switch A up/down.
WIPER SERVICE MODE VIDEO
To view a video on your mobile device, snap this QR Code or visit the listed website. Refer to inside cover for more information.
www.youtube.com/KiaFeatureVideos
QR CODE
§ When the Engine Start/Stop button is in the ON position and the wiper switch is in AUTO mode, the wiper will automatically operate once to perform a self-check of the system
§ Set the wiper to the OFF position when the wiper is not in use
§ If going through a car wash, remind the attendant to keep the vehicle in Neutral (N) and keep the engine running. Also, disable the Smart Power Liftgate* lid control, turn off the auto rain sensing wipers and fold in the mirrors
§
Moving lever to HI increases Intermittent wipe frequency and wipe speed.Moving lever to LO decreases frequency of wipes.
§ Pressing button A up increases Intermittent wipe frequency and wipe speed. Pressing button down decreases frequency of wipes.
QUICK TIPS
C
*IF EQUIPPED

37
Forward*/Reverse Parking Distance Warning (PDW)†6
Forward/Reverse Parking Distance Warning (PDW )* A is a supplemental system that is designed to assist the
driver by chiming if an object is detected within the sensing areas in the front or rear of the vehicle when moving
forward or backing up.
When the Engine Start /Stop button is ON and the shift lever is in R (Reverse), the system is activated and
the Forward/Reverse Parking Distance Warning (PDW )* button indicator is illuminated.
REMINDERS:
§
If the vehicle is moving at speeds over 6 mph, the system may not activate
§
When more than two objects are sensed at the same time, the closest one will be recognized first
§ Forward/Reverse Parking Distance Warning (PDW )* is not a substitute for proper and safe backing-up procedures. Always drive safely and use caution when backing up. Forward/Reverse Parking Distance Warning (PDW )* may not detect every object behind or in front of the vehicle
P
R
N
D
AUTO
HOLD
DRIVE MODE
OFFOFF
P
(Rear sensors shown)
A
See section 4 in the Owner’s Manual for more information.
CENTER PANEL
CENTER PANEL
ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLE TE OPERATING INFORMATION AND SAFETY WARNINGS.*IF EQUIPPED†LEG AL DISCL AIMERS ON BACK INSIDE COVER

50
Auto-Dimming Rearview Mirror
Designed to help reduce glare from a vehicle’s headlights located in the rear and
also connect up to three electronic transmitters in one location. Press the on/off
button F to turn the auto-dimming function on or off.
REMINDER: Mirror indicator light will illuminate when automatic dimming is ON.
How to Sync Transmitter
1. Press and release A, B or D button
– If the indicator C flashes slowly in red, go to Step 3 (Programming)
– If the indicator C is continuously turned ON or flashes rapidly in red
several times, go to Step 2 (Erasing)
2. Press and hold the button you wish to erase the program for
approximately 15-25 seconds until the LED flashes slowly in Red
3. Hold the Garage Door Opener Original Transmitter near the HomeLink Mirror
4.
Press and hold the desired button (A, B or D) and the Original Transmitter button until the indicator C is turned on continuously or flashes rapidly in red. This indicates the programming is completed
To complete programming of a Rolling Code garage door opener:
1. Firmly press and release the “Learn,” “Smart,” or “Program” button of the garage door opener while the
indicator C flashes slowly in red. Once the button is pressed, you have approximately 30 seconds to
initiate the next step
2. Return to the vehicle and firmly press and hold the HomeLink button for two seconds and release. Repeat
this up to three times to complete the programming. Do not press the HomeLink button rapidly. At this
point, programming is complete and your device should operate
Operating HomeLink®: Press one of the programmed
HomeLink® buttons.
Erasing programmed buttons: Press and hold the left A and center D
buttons simultaneously for approximately 20 seconds, until the indicator
light begins to flash, and then release both buttons within 30 seconds.
HomeLink® with Auto-Dimming Rearview Mirror*† 14
For more information, go to HomeLink.com or call (800) 355-3515.
HOMELINK SUPPORT
To view this website on your mobile device, snap this QR Code or visit the listed website. Refer to inside cover for more information.
www.youtube.com/KiaFeatureVideos
QR CODE
§ Erasing programmed buttons will delete all trained transmitters
QUICK TIP
§ If the indicator C flashes rapidly in red continuously, but if the garage door opener does not operate, please continue to follow Rolling Code Programming steps below
QUICK TIP
See section 4 in the Owner’s Manual for more information.
OTHER KEY FEATURES
OTHER KEY FE AT URE S
*IF EQUIPPED†LEG AL DISCL AIMERS ON BACK INSIDE COVER
E
A HomeLink® Channel 1 button
B HomeLink® Channel 2 button
C Status Indicator LED
D HomeLink® Channel 3 button
E Rear light sensor
F Dimming ON/OFF button
G Compass control button
H Compass display
AB
C
D
E
FG
H
REMINDERS:
§ A ladder may be needed to access the garage door opener
§ A second person may be needed to help
§ Some of the steps are time sensitive