flat tire KIA STONIC 2018 User Guide

• If the low pressure light is illumina‐ted.
• If the suspension or ABS has been re‐ placed.
CAUTION
If the system is set without adjust‐ing tire pressure, false alarm couldoccur or the telltale will not be dis‐played even though the vehicle issignificantly under-inflated.Make sure all tires are properly ad‐justed to the recommended pressurewhen setting.If the system is not set even in re‐quired situations, false alarm couldoccur or the telltale will not be dis‐played even though the vehicle issignificantly under-inflated.The system will not be set if youpress the SET switch (2) while driv‐ing. Make sure to stop the vehicleand press the switch (2) for over 3seconds.•Be sure the tire is cold before in‐flating the pressure.A cold tire means the vehicle hasbeen sitting for 3 hours or drivenwithin 1.6km (1mile).
Indication of Low Tire Pressure
0:#-
The () warning light will illuminate
when an under-inflated tire is indica‐ ted. In certain types, the above mes‐
sage might be displayed on the cluster.
If the warning light illuminates, reduce
your speed, avoid hard cornering and rapid braking. Have your vehicle inspec‐
ted by a professional workshop. Kia
recommends to visit an authorized Kia dealer/service partner.
Check the pressure of all tires and in‐
flate to the proper pressure according
to procedures, and if required, replace or repair the tires. If you cannot reach a close service sta‐
tion, stop the vehicle at a safe place,
check all tires and operate the TPMS setting procedure. If you are unable to
adjust the tire pressure, use the repair
tools to repair or change to spare tire and contact a professional workshop.
Kia recommends to call an authorized
Kia dealer/service partner.
You may not be able to identify low tire
pressure visually. Use precise tools to measure and adjust tire pressure.
Please note that a tire that is hot due
to prolonged driving, therefore will have high pressure. We recommend you to
measure and adjust the tire pressure
after the vehicle has driven for less than 1.6 km (1 mile) within 3 hours.
CAUTION
•The indicator may remain illumina‐ted after changing to a spare tire,because radius of spare tire is dif‐ferent. Be sure to change to a reg‐ular tire.
(Continued)

7-09
7
What to do in an emergency

(Continued)
•For safe driving, please note thatthe TPMS is not a substitute forproper tire maintenance. It is thedriver’s responsibility to maintaincorrect tire pressure, and all tiresshould be checked monthly tomaintain the recommended pres‐sure.
•The warning light may illuminate ifthe system is not set in requiredsituations.
•In cold weather, the low tire pres‐sure warning light may illuminateeven if the tire was adjusted tothe proper pressure. It does notmean your TPMS is malfunctioningbecause the decreased tempera‐ture leads to a lowering of tirepressure. Check the tires and ad‐just to the recommended pressure.
•System performance may reducein the following situations.-Improper system setting
-Using tires on the market (Origi‐nal tire recommended)
-Driving on snowy, slippery, orunpaved roads
(Continued)
(Continued)
-Hard cornering, rapid accelerat‐ing and braking repeatedly
-Driving too slow or fast
-If the vehicle is overloaded
-If a spare tire or snow chain isinstalled
•When filling tires with more air,conditions to turn off the low tirepressure telltale may not be met.This is because a tire inflator has amargin of error in performance.The low tire pressure telltale willbe turned off if the tire pressure isabove the recommended tire infla‐tion pressure.
WARNING
•Driving with an under-inflated tirecauses the tire to overheat andlead to tire failure. It also reducestire tread life, handling of the vehi‐cle, braking ability, and fuel effi‐ciency, causing instability of thevehicle. In this case, contact pro‐fessional workshop to maintainproper tire pressure. Kia recom‐mends to contact an authorizedKia dealer/service partner.
•Sudden damage to the tire causedby external factors may not be in‐dicated immediately. If the vehicleis unstable, immediately removeyour foot off the accelerator ped‐al, move the vehicle to a safe posi‐tion for inspection.
Tire Pressure Monitoring
System malfunction
The TPMS malfunction indicator will il‐
luminate () after it blinks for approx‐
imately 1 minute when there is a prob‐ lem with the Tire Pressure Monitoring
System. This sequence will continue upon subsequent vehicle start-ups as
long as the malfunction exists.
What to do in an emergency
7-10

IF YOU HAVE A FLAT TIRE (WITH SPARE TIRE, IF EQUIPPED)
Jack and tools
0:#%
The jack, jack handle, wheel lug nut
wrench are stored in the luggage com‐ partment.
Pull up the luggage box cover to reach
this equipment. 1. Jack handle
2. Jack
3. Wheel lug nut wrench
Jacking instructions
The jack is provided for emergency tire
changing only.
To prevent the jack from L

removing the wheel lug nuts, make
sure the vehicle is stable and that
there is no chance for movement or slippage.
9. Loosen the wheel nuts and remove them with your fingers. Slide the
wheel off the studs and lay it flat
so it cannot roll away. To put the
wheel on the hub, pick up the spare
tire, line up the holes with the studs and slide the wheel onto
them.
If this is difficult, tip the wheel
slightly and get the top hole in the
wheel lined up with the top stud.
Then jiggle the wheel back and
forth until the wheel can be slid
over the other studs.
WARNING
Wheels may have sharp edges. Han‐dle them carefully to avoid possiblesevere injury. Before putting thewheel into place, be sure that thereis nothing on the hub or wheel (suchas mud, tar, gravel, etc.) that inter‐feres with the wheel from fittingsolidly against the hub.
(Continued)
(Continued)
If there is, remove it. If there is notgood contact on the mounting sur‐face between the wheel and hub,the wheel nuts could come loose andcause the loss of a wheel. Loss of awheel may result in loss of control ofthe vehicle. This may cause seriousinjury or death.
10. To reinstall the wheel, hold it on the studs, put the wheel nuts on the
studs and tighten them finger
tight. Jiggle the tire to be sure it is
completely seated, then tighten
the nuts as much as possible with
your fingers again.
11. Lower the vehicle to the ground by turning the wheel nut wrenchcounterclockwise.
Then position the wrench as shown in
the drawing and tighten the wheel nuts. Be sure the socket is seated com‐
pletely over the nut. Do not stand on
the wrench handle or use an extension pipe over the wrench handle. Go around
the wheel tightening every other nut
until they are all tight. Then double- check each nut for tightness. After
changing wheels, have the system
checked by a professional workshop. Kia recommends to visit an authorized
Kia dealer/service partner.
Wheel nut tightening torque:
Steel wheel & aluminum alloy wheel:
11~13kgf·m (79~94lb·ft)

7-15
7
What to do in an emergency

If you have a tire gauge, remove the
valve cap and check the air pressure. If the pressure is lower than recommen‐
ded, drive slowly to the nearest service
station and inflate to the correct pres‐ sure. If it is too high, adjust it until it is
correct. Always reinstall the valve cap
after checking or adjusting tire pres‐ sure. If the cap is not replaced, air may
leak from the tire. If you lose a valve
cap, buy another and install it as soon as possible.
After you have changed wheels, always
secure the flat tire in its place and re‐
turn the jack and tools to their proper storage locations.
CAUTION
Your vehicle has metric threads onthe wheel studs and nuts. Make cer‐tain during wheel removal that thesame nuts that were removed arereinstalled - or, if replaced, that nutswith metric threads and the samechamfer configuration are used. In‐stallation of a non-metric thread nuton a metric stud or vice-versa willnot secure the wheel to the hubproperly and will damage the stud sothat it must be replaced.
(Continued)
(Continued)
Note that most lug nuts do not havemetric threads. Be sure to use ex‐treme care in checking for threadstyle before installing aftermarketlug nuts or wheels. If in doubt, con‐sult a professional workshop. Kiarecommends to consult an author‐ized Kia dealer/service partner.
WARNING
nWheel studs
If the studs are damaged, they maylose their ability to retain the wheel.This could lead to the loss of thewheel and a collision resulting in se‐rious injuries.
To prevent the jack, jack handle, wheel
lug nut wrench and spare tire from rat‐ tling while the vehicle is in motion,
store them properly.
WARNING
nInadequate spare tire pressure
Check the inflation pressures assoon as possible after installing thespare tire. Adjust it to the specifiedpressure, if necessary. Refer toL

(Continued)
•The operation of this vehicle is notrecommended with more than onecompact spare tire in use at thesame time.
WARNING
The compact spare tire is for emer‐gency use only. Do not operate yourvehicle on this compact spare at thespeed over 80 km/h (50 mph). Theoriginal tire should be repaired or re‐placed as soon as possible to avoidfailure of the spare possibly leadingto personal injury or death.
The compact spare should be inflated
to 420 kPa (60 psi).
NOTICE
Check the inflation pressure after in‐
stalling the spare tire. Adjust it to
the specified pressure, as necessary.
When using a compact spare tire, ob‐
serve the following precautions: • Under no circumstances should you
exceed 80 km/h (50 mph); a higherspeed could damage the tire.
• Ensure that you drive slowly enough to avoid all hazards. Any road hazard,
such as a pothole or debris, could se‐
riously damage the compact spare.
• Any continuous road use of this tire could result in tire failure, loss of ve‐
hicle control, and possible personal in‐ jury.
• Do not exceed the vehicle’s maximum load rating or the load-carrying ca‐
pacity shown on the sidewall of the
compact spare tire.
• Avoid driving over obstacles. The compact spare tire diameter is small‐
er than the diameter of a convention‐
al tire and reduces the ground clear‐
ance approximately 2.5 cm (1 inch),
which could result in damage to the
vehicle.
• Do not take the vehicle through an automatic car wash while the com‐
pact spare tire is installed.
• Do not use tire chains on the tempo‐ rary compact tire. Because of the
smaller size, a tire chain will not fit properly. This could damage the vehi‐
cle and result in loss of the chain. • Temporary compact tire should not
be installed on the front axle if the
vehicle must be driven in snow or on
ice.
• Do not use the temporary compact tire on any other vehicle because this
tire has been designed especially for
your vehicle.
• The temporary compact tire tread life is shorter than a regular tire. In‐
spect your temporary compact tire regularly and replace worn compact
spare tires with the same size and
design, mounted on the same wheel.
• The temporary compact tire should not be used on any other wheels, norshould standard tires, snow tires,
wheel covers or trim rings be used
with the temporary compact spare
wheel. If such use is attempted, dam‐
age to these items or other car com‐ ponents may occur.
• Do not use more than one temporary compact tire at a time.
• Do not tow a trailer while the tempo‐ rary compact tire is installed.

7-17
7
What to do in an emergency

IF YOU HAVE A FLAT TIRE (WITH TIRE MOBILITY KIT, IF EQUIPPED)
0:#%
Please read the instructions before us‐
ing the Tire Mobility Kit. 1. Compressor
2. Sealant bottle
The Tire Mobility Kit is a temporary fix to the tire and have the tire inspected
by a professional workshop as soon as
possible. Kia recommends to visit an authorized Kia dealer/service partner.
CAUTION
nOne sealant for one tire
(Continued)
(Continued)
When two or more tires are flat, donot use the tire mobility kit becausethe supported one sealant of TireMobility Kit is only used for one flattire.
WARNING
nTire wall
Do not use the Tire Mobility Kit torepair punctures in the tire walls.This can result in an accident due totire failure.
WARNING
nTemporary fix
Have your tire repaired as soon aspossible. The tire may lose air pres‐sure at any time after inflating withthe Tire Mobility Kit.
CAUTION
•When replacing or repairing thetire after using tire sealant, makecertain to remove the sealant at‐tached to the inner part of the tireand wheel. If the sealant is not re‐moved, noise and vibration mayoccur.
•We recommend to use original Kiamanufactured sealant.
•If the TPMS warning light illumi‐nates after using the TMK, haveyour vehicle inspected by a profes‐sional workshop. Kia recommendsto contact an authorized Kia deal‐er/service partner.
What to do in an emergency
7-20

Introduction
With the Tire Mobility Kit (TMK) you
stay mobile even after experiencing a tire puncture.
The system of compressor and sealing
compound effectively and comfortably
seals most punctures in a passenger car tire caused by nails or similar ob‐
jects and reinflates the tire.
After you ensured that the tire is prop‐
erly sealed you can drive cautiously on the tire (up to 200 km (120 miles)) at a
max. speed of 80 km/h (50 mph) in or‐
der to reach a vehicle or tire dealer to have the tire replaced. It is possible that some tires, especially
with larger punctures or damage to the
sidewall, cannot be sealed completely.
Air pressure loss in the tire may ad‐ versely affect tire performance.
For this reason, you should avoid
abrupt steering or other driving ma‐
neuvers, especially if the vehicle is heavily loaded or if a trailer is in use.
The TMK is not designed or intended as
a permanent tire repair method and is
to be used for one tire only.This instruction shows you step by step
how to temporarily seal the puncture simply and reliably.
Read the section L

Components of the Tire Mobility Kit (TMK)1. Speed restriction label
2. Sealant bottle and label with speedrestriction
3. Filling hose from sealant bottle to wheel
4. Connectors and cable for the power outlet direct connection
5. Holder for the sealant bottle
6. Compressor
7. On/off switch
8. Pressure gauge for displaying the tire inflation pressure
9. Button for reducing tire inflation pressure
Connectors, cable and connection hose are stored in the compressor housing.
WARNING
Before using the Tire Mobility Kit,follow the instructions on the seal‐ant bottle.Remove the label with the speed re‐striction from the sealant bottle andapply it to the steering wheel.
(Continued)
What to do in an emergency
7-22

(Continued)
Please note the expiry date on thesealant bottle.
Using the Tire Mobility Kit
1. Detach the speed restriction label(1) from the sealant bottle (2), and
place it in a highly visible place in‐
side the vehicle such as on the
steering wheel to remind the driver
not to drive too fast.
2. Filling the sealant Strictly follow the specified sequence, otherwise
the sealant may escape under high pressure.
3. Shake the sealant bottle.
4. Connect the filling hose (3) onto the connector of the sealant bottle (A).
5. Ensure that the button (9) on the compressor is not pressed.
6. Unscrew the valve cap from the valve of the defective wheel and
screw the filling hose (3) of the
sealant bottle onto the valve.
7. Insert the sealant bottle into the housing of the compressor so that
the bottle is upright (B).
8. Ensure that the compressor is switched off, position 0.
9. Connect between compressor and the vehicle power outlet using the
cable and connectors.
NOTICE
Only use the front passenger side
power outlet.
10. With the ignition switched on or en‐ gine start/stop button position on:
Switch on the compressor and let it
run for approximately 3 minutes to
fill the sealant. The inflation pres‐
sure of the tire after filling is unim‐
portant.
11. Switch off the compressor.

7-23
7
What to do in an emergency