flat tire KIA STONIC 2018 Owner's Manual

12. Detach the hose from the sealantbottle connector and from the tire
valve.
Return the Tire Mobility Kit to its stor‐ age location in the vehicle.
WARNING
Carbon monoxide poisoning and suf‐focation is possible if the engine isleft running in a poorly ventilated orunventilated location (such as insidea building).
Distributing the sealant
13. Immediately drive approximately 7~10km (4~6miles or, about 10min)
to evenly distribute the sealant in
the tire.
CAUTION
Do not exceed a speed of 60 km/h(35 mph). If possible, do not fall be‐low a speed of 20 km/h (12 mph).
(Continued)
(Continued)
While driving, if you experience anyunusual vibration, ride disturbanceor noise, reduce your speed anddrive with caution until you cansafely pull off of the side of theroad. Call for road side service ortowing.When you use the Tire Mobility Kit,the wheel may be stained by seal‐ant. Therefore, remove the wheelstained by sealant and have the ve‐hicle inspected at a professionalworkshop. Kia recommends to visitan authorized Kia dealer/servicepartner.
Checking the tire inflation
pressure
1. After driving approximately 7~10 km (4~6 miles or about
10 minutes), stop at a suitable lo‐
cation.
2. Connect the filling hose (3) of the compressor (clip mounted side) di‐
rectly and then connect the filling
hose (3) (opposite side) to the tire
valve. 3. Connect between compressor and
the vehicle battery using the cable
and connectors.
4. Adjust the tire inflation pressure to 200 kPa (29 psi). With the ignition
switched on, proceed as follows.
-
To increase the inflation pressure:
Switch on the compressor, position I.
To check the current inflation pres‐
sure setting, briefly switch off the
compressor.
WARNING
Do not let the compressor run formore than 10 minutes, otherwisethe device will overheat and may bedamaged.
-To reduce the inflation pressure:
Press the button (9) on the compres‐
sor.
What to do in an emergency
7-24

EMERGENCY COMMODITY (IF EQUIPPED)
There are some emergency commodi‐ ties in the vehicle to help you respond
to the emergency situation.
Fire extinguisher
If there is a small fire and you know
how to use the fire extinguisher, take the following steps carefully. 1. Pull the pin at the top of the extin‐ guisher that keeps the handle from
being accidentally pressed.
2. Aim the nozzle toward the base of the fire.
3. Stand approximately 2.5 m (8 ft) away from the fire and squeeze
the handle to discharge the extin‐
guisher. If you release the handle,
the discharge will stop.
4. Sweep the nozzle back and forth at the base of the fire. After the fire
appears to be out, watch it careful‐
ly since it may re-ignite.
First aid kit
There are some items such as scissors,
bandage and adhesive tape etc. in the kit to give first aid to an injured person.
Triangle reflector
Place the triangle reflector on the roadto warn oncoming vehicles during
emergencies, such as when the vehicle
is parked by the roadside due to any problems.
Tire pressure gauge (if
equipped)
Tires normally lose some air in day-to-
day use, and you may have to add a
few pounds of air periodically and it is
not usually a sign of a leaking tire, but
of normal wear. Always check tire pres‐
sure when the tires are cold because
tire pressure increases with tempera‐
ture.
To check the tire pressure, take the fol‐ lowing steps; 1. Unscrew the inflation valve cap that is located on the rim of the
tire.
2. Press and hold the gauge against the tire valve. Some air will escape
as you begin and more will escape
if you don't press the gauge in
firmly.
3. A firm non-leaking push will acti‐ vate the gauge. 4. Read the tire pressure on the
gauge to know whether the tire
pressure is low or high.
5. Adjust the tire pressures to the specified pressure. Refer to L

Changing the engine oil and filter...................................... 8-45
Engine oil (Diesel)...................................................................... 8-46 Checking the engine oil level................................................8-46
Changing the engine oil and filter...................................... 8-46
Engine coolant........................................................................... 8-48 Checking the coolant level................................................... 8-48
Changing the coolant............................................................ 8-51
Brake/Clutch fluid .....................................................................8-52 Checking the brake/clutch fluid level................................. 8-52
Automatic transaxle fluid ....................................................... 8-53 Checking the automatic transaxle fluid level .................. 8-53
Changing the automatic transaxle fluid............................ 8-54
Washer fluid............................................................................... 8-55 Checking the washer fluid level.......................................... 8-55
Parking brake............................................................................. 8-56 Checking the parking brake................................................. 8-56
Fuel filter (for diesel)................................................................ 8-57 Draining water from the fuel filter.................................... 8-57
Fuel filter cartridge replacement....................................... 8-57
Air cleaner.................................................................................. 8-58 Filter replacement.................................................................8-58
Climate control air filter........................................................... 8-59 Filter inspection..................................................................... 8-59
Wiper blades...............................................................................8-60 Blade inspection.................................................................... 8-60
Blade replacement................................................................ 8-60
Battery........................................................................................8-63 For best battery service...................................................... 8-63
Battery capacity label.......................................................... 8-64
Battery recharging................................................................8-65 Reset items............................................................................ 8-65
Tires and wheels....................................................................... 8-67 Tire care.................................................................................. 8-67
Recommended cold tire inflation pressures..................... 8-67
Checking tire inflation pressure.......................................... 8-68
Tire rotation........................................................................... 8-69
Wheel alignment and tire balance...................................... 8-70
Tire replacement................................................................... 8-70
Wheel replacement............................................................... 8-72
Tire traction........................................................................... 8-72
Tire maintenance.................................................................. 8-72
Tire sidewall labeling............................................................ 8-72
Low aspect ratio tire ........................................................... 8-75
Fuses........................................................................................... 8-77 Inner panel fuse replacement............................................. 8-79
Engine compartment fuse replacement........................... 8-80
Fuse/relay panel description............................................... 8-82
Light bulbs................................................................................8-104 Bulb replacement precaution............................................8-104
Light bulb position (Front).................................................8-106
Light bulb position (Rear).................................................. 8-107
Light bulb position (Side)................................................... 8-108
Side repeater lamp (LED type) bulb Replacement........ 8-108
Side repeater lamp (bulb type) bulb Replacement....... 8-109
Headlamp (Low/High beam) bulb replacement
(Headlamp Type A)............................................................. 8-109
Front turn signal lamp bulb replacement (Head‐
lamp Type A)........................................................................8-110
Position lamp / Day time running lamp bulb re‐
placement (Headlamp Type A)......................................... 8-110


8

OWNER MAINTENANCE
The following lists are vehicle checks
and inspections that should be per‐
formed at the frequencies indicated to help ensure safe, dependable operation
of your vehicle.
Any adverse conditions should be
brought to the attention of your dealer as soon as possible.
These Owner Maintenance Checks are
generally not covered by warranties
and you may be charged for labor, parts and lubricants used.
Owner maintenance schedule
When you stop for fuel:
• Check the engine oil level.
• Check the coolant level in the coolant reservoir.
• Check the windshield washer fluid level.
• Look for low or under-inflated tires.
WARNING
Be careful when checking your en‐gine coolant level when the engine ishot. Scalding hot coolant and steam
(Continued)
(Continued)
may blow out under pressure. Thiscould cause burns or other seriousinjury.
While operating your vehicle:
• Note any changes in the sound of the exhaust or any smell of exhaust
fumes in the vehicle.
• Check for vibrations in the steering wheel. Notice any increased steering
effort or looseness in the steering
wheel, or change in its straight-
ahead position.
• Notice if your vehicle constantly turns slightly or L

TIRES AND WHEELS

Tire care
For proper maintenance, safety, and
maximum fuel economy, you must al‐
ways maintain recommended tire infla‐ tion pressures and stay within the load
limits and weight distribution recom‐
mended for your vehicle.
Recommended cold tire inflation
pressures
All tire pressures (including the spare)
should be checked when the tires are cold. L

(Continued)
•Be sure to reinstall the tire infla‐tion valve caps. Without the valvecap, dirt or moisture could get intothe valve core and cause air leak‐age. If a valve cap is missing, in‐stall a new one as soon as possi‐ble.
WARNING
nTire Inflation
Overinflation or underinflation canreduce tire life, adversely affect ve‐hicle handling, and lead to suddentire failure. This could result in lossof vehicle control and potential in‐jury.
CAUTION
nTire pressure
Always observe the following:
(Continued)
(Continued)
•Check tire pressure when the tiresare cold. (After vehicle has beenparked for at least three hours orhasn't been driven more than 1.6km (one mile) since startup.)
•Check the pressure of your sparetire each time you check the pres‐sure of other tires.
•Never overload your vehicle. Becareful not to overload a vehicleluggage rack if your vehicle isequipped with one.
•Worn, old tires can cause acci‐dents. If your tread is badly worn,or if your tires have been dam‐aged, replace them.
Checking tire inflation pressure
Check your tires once a month or more.
Also, check the tire pressure of the
spare tire.
How to check
Use a good quality gauge to check tire
pressure. You can not tell if your tires
are properly inflated simply by looking
at them. Radial tires may look properly
inflated even when they're underinfla‐ ted. Check the tire's inflation pressure when
the tires are cold. - "Cold" means your
vehicle has been sitting for at least three hours or driven no more than 1.6
km (1 mile).
Remove the valve cap from the tire
valve stem. Press the tire gauge firmly onto the valve to get a pressure meas‐
urement. If the cold tire inflation pres‐
sure matches the recommended pres‐ sure on the tire and loading information
label, no further adjustment is necessa‐
ry. If the pressure is low, add air until
you reach the recommended amount.
If you overfill the tire, release air by pushing on the metal stem in the cen‐
ter of the tire valve. Recheck the tire
pressure with the tire gauge. Be sure to put the valve caps back on the valve
stems. They help prevent leaks by
keeping out dirt and moisture.
WARNING
•Inspect your tires frequently forproper inflation as well as wearand damage. Always use a tirepressure gauge.
(Continued)
Maintenance
8-68

Compact spare tire replacement (if
equipped)
A compact spare tire has a shortertread life than a regular size tire. Re‐
place it when you can see the tread
wear indicator bars on the tire. The re‐ placement compact spare tire should be
the same size and design tire as the
one provided with your new vehicle and
should be mounted on the same com‐ pact spare tire wheel. The compact
spare tire is not designed to be moun‐
ted on a regular size wheel, and the compact spare tire wheel is not de‐
signed for mounting a regular size tire.
Wheel replacement
When replacing the metal wheels for
any reason, make sure the new wheels are equivalent to the original factory
units in diameter, rim width and offset.
WARNING
A wheel that is not the correct sizemay adversely affect wheel andbearing life, braking and stoppingabilities, handling characteristics,ground clearance, body-to-tire
(Continued)
(Continued)
clearance, snow chain clearance,speedometer and odometer calibra‐tion, headlight aim and bumperheight.
Tire traction
Tire traction can be reduced if you drive
on worn tires, tires that are improperly inflated or on slippery road surfaces.
Tires should be replaced when tread
wear indicators appear. Slow down whenever there is rain, snow or ice on
the road to reduce the possibility of
losing control of the vehicle.
Tire maintenance
In addition to proper inflation, correct
wheel alignment helps to decrease tire wear. If you find a tire is worn uneven‐
ly, have a professional workshop check
the wheel alignment. Kia recommends to visit an authorized Kia dealer/service
partner.
When you have new tires installed,
make sure they are balanced. This will increase vehicle ride comfort and tire
life. Additionally, a tire should always
be rebalanced if it is removed from the wheel.
Tire sidewall labeling
This information identifies and de‐
scribes the fundamental characteristics of the tire and also provides the tire
identification number (TIN) for safety
standard certification. The TIN can be used to identify the tire in case of a re‐
call.
1. Manufacturer or brand name
Manufacturer or Brand name is shown.
Maintenance
8-72

WARNING
nTire age
Tires degrade over time, even whenthey are not being used.Regardless of the remaining tread,we recommend that tires be re‐placed after approximately six (6)years of normal service. Heat causedby hot climates or frequent highloading conditions can accelerate theaging process. Failure to follow thiswarning can result in sudden tirefailure, which could lead to a loss ofcontrol and an accident involving se‐rious injury or death.
4. Tire ply composition and material
The number of layers or plies of rub‐
ber-coated fabric in the tire. Tire man‐ ufacturers also must indicate the ma‐
terials in the tire, which include steel,
nylon, polyester, and others. The letter "R" means radial ply construction; the
letter "D" means diagonal or bias ply
construction; and the letter "B" means belted-bias ply construction.
5. Maximum permissible inflation
pressure
This number is the greatest amount of
air pressure that should be put in the
tire. Do not exceed the maximum per‐ missible inflation pressure. Refer to the
Tire and Loading Information label for
recommended inflation pressure.
6. Maximum load rating
This number indicates the maximum
load in kilograms and pounds that can be carried by the tire. When replacing
the tires on the vehicle, always use a
tire that has the same load rating as the factory installed tire.
7. Uniform tire quality grading
Quality grades can be found where ap‐
plicable on the tire sidewall between tread shoulder and maximum section
width.
For example:TREADWEAR 200TRACTION AA
TEMPERATURE A
Tread wear
The tread wear grade is a comparative
rating based on the wear rate of the tire when tested under controlled con‐
ditions on a specified government test
course. For example, a tire graded 150 would wear one-and-a-half times (1½)
as well on the government course as a
tire graded 100.
The relative performance of tires de‐ pends upon the actual conditions of
their use, however, and may depart sig‐
nificantly from the norm due to varia‐
tions in driving habits, service practices and differences in road characteristics
and climate.
These grades are molded on the side-
walls of passenger vehicle tires. The tires available as standard or optional
equipment on your vehicle may vary
with respect to grade.
Traction - AA, A, B & C
The traction grades, from highest to lowest, are AA, A, B and C. Those
grades represent the tire’s ability to
stop on wet pavement as measured under controlled conditions on specified
government test surfaces of asphalt
and concrete. A tire marked C may have poor traction performance.
Maintenance
8-74

Temperature - A, B & C
The temperature grades are A (the
highest), B, and C, representing the tire’s resistance to the generation of
heat and its ability to dissipate heat
when tested under controlled condi‐ tions on a specified indoor laboratory
test wheel.
Sustained high temperature can cause
the material of the tire to degenerate and reduce tire life, and excessive tem‐
perature can lead to sudden tire failure.
Grades B and A represent higher levels of performance on the laboratory test
wheel than the minimum required by
law.
WARNING
The traction grade assigned to thistire is based on straight-ahead brak‐ing traction tests, and does not in‐clude acceleration, cornering, hydro‐planing, or peak traction characteris‐tics.
WARNING
nTire temperature
The temperature grade for this tireis established for a tire that is prop‐erly inflated and not overloaded. Ex‐cessive speed, underinflation, or ex‐cessive loading, either separately orin combination, can cause heat build-up and possible sudden tire failure.This can cause loss of vehicle controland serious injury or death.
Low aspect ratio tire (if
equipped)
Low aspect ratio tires, whose aspect
ratio is lower than 50, are provided for sporty looks.
Because the low aspect ratio tires are
optimized for handling and braking, it
may be more uncomfortable to ride in and there is more noise compare with
normal tires.
CAUTION
Because the sidewall of the low as‐pect ratio tire is shorter than the
(Continued)
(Continued)
normal, the wheel and tire of thelow aspect ratio tire is easier to bedamaged. So, follow the instructionsbelow.•When driving on a rough road oroff road, drive cautiously becausetires and wheels may be damaged.And after driving, inspect tires andwheels.
•When passing over a pothole,speed bump, manhole, or curbstone, drive slowly so that thetires and wheels are not damaged.
•If the tire is impacted, inspect thetire condition or contact a profes‐sional workshop. Kia recommendsto visit an authorized Kia dealer/service partner.
•To prevent damage to the tire, in‐spect the tire condition and pres‐sure every 3,000km.

8-75
8
Maintenance

Headlamp and front fog lamp
aiming (for Europe)
Headlamp aiming
¥
5ZQF
"
¥
5ZQF
#
1. Inflate the tires to the specifiedpressure and remove any loads from the vehicle except the driver,
spare tire, and tools.
2. The vehicle should be placed on a flat floor.
3. Draw vertical lines (Vertical lines passing through respective head
lamp centers) and a horizontal line
(Horizontal line passing through center of head lamps) on the
screen.
4. With the head lamp and battery in normal condition, aim the head
lamps so the brightest portion falls
on the horizontal and vertical lines.
5. To aim the low and high beams left or right, turn the driver (1) clock‐
wise or counterclockwise. To aim
the low and high beams up or
down, turn the driver (2) clockwise
or counterclockwise.
Front fog lamp aiming
The front fog lamp can be aimed as the
same manner of the head lamps aim‐ ing.
With the front fog lamps and battery
normal condition, aim the front fog
lamps.
To aim the front fog lamp up or down, turn the driver clockwise or counter‐
clockwise.

8-121
8
Maintenance