heating Lancia Delta 2008 Owner handbook (in English)
[x] Cancel search | Manufacturer: LANCIA, Model Year: 2008, Model line: Delta, Model: Lancia Delta 2008Pages: 258, PDF Size: 4.93 MB
Page 17 of 258
16GETTING TO KNOW YOUR CAR
Go to a Lancia Dealership as soon as possi-
ble if warning light Ueither does not light up
when the key is turned to MAR or if while
travelling the warning light comes on either steady
or blinking (on some versions along with a message
on the display). The operation of the warning light
Umay be checked by the traffic police using spe-
cific devices. Follow the laws in force in the coun-
try where you are driving.
Advanced ESP system (amber)
This warning light comes on when the ignition
key is turned to MAR, but it should go off after
a few seconds. If the warning light does not go off
or stays on together with the LED on the ASR button when
travelling, contact a Lancia Dealership. On certain versions
a dedicated message is displayed. If the warning light
flashes when driving, this indicates that the Advanced ESP
system has cut in.
á
Hill holder system failure (amber)
The áwarning light turns on to indicate a Hill
holder system failure. In this case, contact a
Lancia Dealership as soon as possible. Alter-
natively, on some versions the *symbol is
lit up on the display.
The display will show a dedicated message.
á
*
Glow plug preheating
This warning light comes on when the key is
turned to MAR. It will go out as soon as the glow
plugs have reached a predetermined temperature.
Start the engine as soon as the warning light goes out.
IMPORTANT At high outdoor temperatures the warning
light stays on for an extremely short time.
m
To switch the warning light off, carry out the following
initialization procedure:
turn the ignition key to the ON position;
turn the steering wheel fully both clockwise and anti-
clockwise (to move from the position with the wheels
straight);
turn the ignition key to the OFF position and then turn
it back ON.
If the
áwarning light does not go out after a few
seconds, seek assistance from a Lancia Dealership.
Page 18 of 258
GETTING TO KNOW YOUR CAR17
1
Water in diesel fuel filter (Multijet
versions) (amber)
This warning light comes on when the ignition
key is turned to MAR, but it should go off after
a few seconds. The warning light turns on when there is
water in the diesel fuel filter. The display will show a ded-
icated message.
c
The presence of water in the fuel system cir-
cuit may cause severe damage to the injection
system and irregular engine operation. If the
cwarning light comes on (together with a message
on the display on some versions), go to a Lancia
Dealership as soon as possible to have the system
bled. Water may have been introduced in the tank if
this appears immediately after refuelling: in this
case, stop the engine immediately and contact a
Lancia Dealership.
ABS system failure (amber)
This warning light comes on when the ignition
key is turned to MAR, but it should go off af-
ter a few seconds. The warning light lights up
when the system is either not working or not available.
Under these circumstances the braking system will work
as normal without the extra performance offered by the
ABS system.
Drive carefully to the nearest Lancia Dealership to have
the system checked.
The display will show a dedicated message.
>
Lancia Code system failure (amber)
This warning light (or symbol on the display),
when on constantly with the ignition key turned
to MAR, indicates a possible failure (see “Lancia
Code system” in chapter 1).
If the
Ywarning light (or symbol in the display) is blink-
ing, this means that the vehicle is not protected by the en-
gine inhibitor device (see “Lancia Code system” in chap-
ter 1).
Contact a Lancia Dealership to have all the keys stored.
Alarm failure (where provided)
A fault with the alarm system is signalled by this warn-
ing light (or symbol in the display) coming on. Contact a
Lancia Dealership as soon as possible.
The display will show a dedicated message.
Y
Glow plug heating failure
The warning light will blink in the event of a failure in the
glow plug preheating system. Go to a Lancia Dealership
as soon as possible.
The display will show a dedicated message.
Page 20 of 258
GETTING TO KNOW YOUR CAR19
1
Particularly strong radio frequency interfer-
ence may cause the T.P.M.S. system to func-
tion incorrectly. This condition is indicated
to the driver by a message (where provided).
The warning message will go off automatically as
soon as the radio-frequency noise ceases to disturb
the system.
External lighting failure (amber)
This warning light (or symbol on the display)
comes on when a failure is detected in any of
the following lights:
sidelights;
brake lights (where provided);
rear fog lights;
direction indicators;
number plate lights;
daylight lights.
W
Rear fog lights (amber)
The warning light comes on when the rear fog
lights are turned on.
4
Front fog lights (green)
The warning light comes on when the front fog
lights are turned on.
5
Direction indicators
(green - intermittent)
The warning lights turn on when the direction
indicator control lever is moved downwards,
upwards or when the hazard warning light
button is pressed.
F
D
IMPORTANT reduce speed immediately if this occurs.
Tyre overheating could irreparably compromise tyre per-
formance and life, and in extreme cases may even cause
the tyre to explode.The fault relating to these lights may be caused by: one or
more burnt lamps, a blown protection fuse or interruption
of the electrical connection.
The display will show a dedicated message.
Page 59 of 258
58GETTING TO KNOW YOUR CAR
heated rear windscreen and door mirrors
demisting/defrosting fig. 26
Press button F (
() to activate the function: When the
function is active, an LED on the button lights up.
This function is timed and will turn off automatically af-
ter 20 minutes. Press
(again to disable the function in
advance.
IMPORTANT Do not apply stickers on the inside of the
rear window over the heating filaments to avoid damage
that might cause it to stop working properly.
IMPORTANT Press
Tto draw air in from the outside
(in this case the LED on the button should be off).Rapid window demisting/defrosting
(MAX-DEF function) fig. 26
Press button G
-to automatically activate the timed op-
eration of all the functions required to rapidly
demist/defrost the windscreen and front windows.
The functions are:
climate control compressor engagement (with an out-
door temperature of above 4°C);
disengagement (if previously engaged) of air recircu-
lation (the LED on button
Tshould be off);
engagement of heated rear windscreen (the LED on
button
-should be on) and door mirror heater coils;
air temperature set to maximum;
activation of air flow.
Activation of air recirculation and enablement of
AQS (Air Quality System) fig. 26
Press button
T.
Air recirculation is carried out according to three possi-
ble operation modes:
automatic control, indicated by the AQS appearing on
the display and the LED on button
Tshould be off;
Page 60 of 258
GETTING TO KNOW YOUR CAR59
1
forced disablement (air recirculation always off, air
drawn in from the outside), - the LED on button
Tshould be off;
forced engagement (air recirculation always on), the
LED on button
Tshould be lit up.
When OFF is pressed, the climate control system auto-
matically activates air recirculation (the LED on button
Tshould be on). It is still possible to activate outside
air recirculation (LED on the button is off) and vice ver-
sa, by pressing button
T.
With the OFF button pressed (LED on the button is lit
up), it is not possible to enable the AQS (Air Quality Sys-
tem) function.
IMPORTANT The air recirculation system makes it pos-
sible to reach the required heating or cooling conditions
faster. Do not use the air recirculation function on
rainy/cold days as it would considerably increase the pos-
sibility of the windows misting up inside, especially if the
climate control system is not switched on. It is advisable
to switch internal air recirculation on while in queues or
in tunnels to prevent the introduction of polluted air. Do
not use the function for a long time, particularly if there
are many passengers on board, to prevent the windows
from misting up.Enabling the AQS (Air Quality System) function
The AQS function (AQS appears on the display), auto-
matically activates internal air recirculation when the out-
side air is polluted (e.g. in traffic queues and tunnels).
IMPORTANT With the AQS function active, after 15 con-
secutive minutes of the internal air recirculation system
functioning, the climate control system enables the intake
of outdoor air for approximately 1 minute to freshen the
air in the passenger compartment. This takes place re-
gardless of the pollution level of the outside air.
Page 104 of 258
GETTING TO KNOW YOUR CAR103
1
When the function is active, “S” is displayed on the in-
strument panel. Press the button once again to deacti-
vate the function and return to the standard driving mode.
IMPORTANT The function is activated about 5 seconds
after the SPORT button is pressed.
IMPORTANT The steering may become slightly stiff fol-
lowing parking manoeuvres involving a lot of steering.
This is normal and caused by a system to prevent the mo-
tor from overheating. No servicing is required. The pow-
er steering system will return to normal operation the next
time the car is used.Under no circumstances should after-market
operations be carried out involving steering
system or steering column modifications (e.g.:
installation of anti-theft device). This could nega-
tively affect performance and safety, cause the lapse
of the warranty and also result in vehicle non-com-
pliance with type-approval requirements.
Before servicing the car, switch off the engine
and remove the key from the ignition device to
activate the steering lock. This is especially
important when the car wheels do not touch the
ground. If this is not possible (if the key must be on
MAR or the engine must be running), remove the
main fuse which protects the electric power steering.
Page 116 of 258
GETTING TO KNOW YOUR CAR115
1
IMPORTANT The steering may become slightly stiff fol-
lowing parking manoeuvres involving a lot of steering.
This is normal and is caused by a system to prevent the
motor from overheating. No servicing is required. The
power steering system will return to normal operation the
next time the car is used.T.P.M.S. SYSTEM
(Tyre Pressure Monitoring System)
(where provided)
The car may be equipped with a tyre pressure monitoring
system (T.P.M.S.). This system comprises a radio fre-
quency transmitter fitted to each wheel (on the wheel rim
inside the tyre), which is able to send information on the
tyre inflation pressure of each wheel to the control unit.
IMPORTANT NOTES ABOUT THE
T.P.M.S. SYSTEM
The fault indications are not stored and will therefore not
be displayed after the engine has been switched off and
then on again. If the fault conditions persist, the control
unit will send the relative indications to the instrument
panel only after the vehicle has been in motion for a short
time.
Before servicing the car, always switch off the
engine and remove the key from the ignition
to activate the steering lock. This is especially
important when the car wheels do not touch the
ground. If this is not possible (the key must be on
MAR or the engine must be running), remove the
main fuse that protects the electric power steering.
The T.P.M.S.system is not able to detect sud-
den tyre inflation pressure losses (for exam-
ple when a tyre explodes). In this case stop
the car, braking with care and avoiding sharp steer-
ing actions.
Page 129 of 258
128SAFETY
PRETENSIONERS
To increase the efficiency of the seat belts, the car is fit-
ted with pretensioners. These devices, in the event of a vi-
olent frontal impact, rewind the seat belts by a few cen-
timetres. In this way they ensure that the seat belt adheres
perfectly to the wearer before the restraining action be-
gins. The seat belt reel locks to indicate that the preten-
sioner has cut in; the seat belt cannot be drawn back up
even when guided manually.
This car is provided with a second pretensioner (in the
running board area). Its activation is signalled by the
shortening of the metal cable.
IMPORTANT To obtain the highest degree of protection
from the action of the pretensioning device, wear the seat
belt keeping it firmly close to the chest and pelvis.
A small amount of smoke may be produced during the ac-
tivation of the pretensioners. This smoke is in no way tox-
ic and presents no fire hazard. The pretensioner does not
require any maintenance or greasing. Anything that mod-
ifies its original conditions invalidates its efficiency. If due
to unusual natural events (floods, sea storms, etc.) the de-
vice has been affected by water and mud, it must neces-
sarily be replaced.
The pretensioner can only be used once. Go
to a Lancia Dealership to have it replaced af-
ter is has been deployed. The expiry date is
shown on the label on the door edge: refer to a Lan-
cia Dealership when the time comes to replace the
device.
Operations which lead to shocks, vibrations
or localised heating (over 100°C for a max-
imum of 6 hours) in the area around the pre-
tensioners may damage or trigger them. These de-
vices are not affected by vibrations caused by ir-
regularities of the road surface or low obstacles such
as kerbs, etc. Contact Lancia Dealership for any as-
sistance.
Page 195 of 258
194IN AN EMERGENCY
42
42
42
42
42
42F1
F2
F3
F6
F4
F530
30
10
10
15
10
FUSE SUMMARY TABLE - Luggage compartment control unit
CONSUMERS FUSE AMPERE DIAGRAM
Right front seat adjustment node
Left front seat adjustment node
Left front seat heating
Right front seat heating
Audio Hi-Fi control unit
BASSBOX loudspeaker (Hi-Fi system)
Page 224 of 258
CARE AND MAINTENANCE223
5
Exterior plastic parts must be cleaned in the same way
as the rest of the car.
Where possible, do not park under trees; the resinous sub-
stance many species release give the paint a dull appearance
and increase the possibility of triggering rust processes.
IMPORTANT Bird droppings must be washed off imme-
diately and thoroughly as the acid they contain is partic-
ularly aggressive.
Detergents cause water pollution. The car
should be washed in areas equipped for col-
lecting and purifying the liquid used in the
washing process.
Windows
Use specific window cleaner products.
Use also clean cloths to avoid scratching the glass or dam-
aging the transparency.
IMPORTANT Wipe the rear window inside gently with a
cloth in the direction of the filaments to avoid damaging
the heating device.
Engine compartment
At the end of each winter, thoroughly wash the engine
compartment, taking care to avoid directly hitting with
the water jet the electronic control units and the relay/fuse
control unit on the left side of the engine compartment
(running direction). Have this operation performed at a
specialised workshop.
IMPORTANT Perform this operation on a cold engine and
with the key at STOP. After the washing operation, make
sure that the various protections (e.g. rubber caps and
guards) have not been removed or damaged.
Front headlights
IMPORTANT Never use aromatic substances (e.g.: petrol)
or ketenes (e.g.: acetone) for cleaning front headlight plas-
tic lens.
To keep intact the aesthetic properties of the
paintwork do not use abrasive and/or pol-
ish products for cleaning the car bodywork.