turn signal Lancia Delta 2008 Owner handbook (in English)

GETTING TO KNOW YOUR CAR11
1The failure of the warning light ¬is indi-
cated by it flashing longer than the expected
4 seconds
“, thus signalling that the front
passenger airbag is deactivated. In addition, the
airbag system automatically disables the airbag on
the passenger’s side (both front and side airbags).
In this case, the warning light
¬may not indicate
a fault in the system. Contact a Lancia Dealership
immediately to have the system checked.
Passenger-side air bag/side bags
deactivated (amber)
The
“warning light comes on when the front
passenger’s airbag and side bag are disabled. With
front passenger’s airbag on, when the ignition key is turned
to MAR the
“warning light comes on steadily for about
4 seconds, flashes for another 4 seconds and then should
go out.
“
The failure of the “warning light is indi-
cated by the
¬it coming on. In addition, the
airbag system automatically disables the
airbag on the passenger’s side (both front and side
airbags, where provided). Contact a Lancia Deal-
ership immediately to have the system checked.
Seat belts unfastened (red)
This warning light lights up when the car is not
moving and the driver’s seat belt is not correctly
fastened. The warning light will flash and a
buzzer will sound if the vehicle is in motion and the front
seat belts are not correctly fastened.
The S.B.R. (Seat Belt Reminder) system buzzer can only
be permanently switched off by a Lancia Dealership.
The system can be reactivated using the Set-up Menu.
<

GETTING TO KNOW YOUR CAR17
1
Water in diesel fuel filter (Multijet
versions) (amber)
This warning light comes on when the ignition
key is turned to MAR, but it should go off after
a few seconds. The warning light turns on when there is
water in the diesel fuel filter. The display will show a ded-
icated message.
c
The presence of water in the fuel system cir-
cuit may cause severe damage to the injection
system and irregular engine operation. If the
cwarning light comes on (together with a message
on the display on some versions), go to a Lancia
Dealership as soon as possible to have the system
bled. Water may have been introduced in the tank if
this appears immediately after refuelling: in this
case, stop the engine immediately and contact a
Lancia Dealership.
ABS system failure (amber)
This warning light comes on when the ignition
key is turned to MAR, but it should go off af-
ter a few seconds. The warning light lights up
when the system is either not working or not available.
Under these circumstances the braking system will work
as normal without the extra performance offered by the
ABS system.
Drive carefully to the nearest Lancia Dealership to have
the system checked.
The display will show a dedicated message.
>
Lancia Code system failure (amber)
This warning light (or symbol on the display),
when on constantly with the ignition key turned
to MAR, indicates a possible failure (see “Lancia
Code system” in chapter 1).
If the
Ywarning light (or symbol in the display) is blink-
ing, this means that the vehicle is not protected by the en-
gine inhibitor device (see “Lancia Code system” in chap-
ter 1).
Contact a Lancia Dealership to have all the keys stored.
Alarm failure (where provided)
A fault with the alarm system is signalled by this warn-
ing light (or symbol in the display) coming on. Contact a
Lancia Dealership as soon as possible.
The display will show a dedicated message.
Y
Glow plug heating failure
The warning light will blink in the event of a failure in the
glow plug preheating system. Go to a Lancia Dealership
as soon as possible.
The display will show a dedicated message.

GETTING TO KNOW YOUR CAR37
1
THE LANCIA CODE SYSTEM
This is an electrical engine locking system which increases
protection against an attempted theft of the car. It is auto-
matically activated when the ignition key is extracted.
Each key contains an electronic device which modulates
the signal emitted during ignition by an antenna built in-
to the ignition device. This signal is the ‘password’ which
changes at each ignition and which the control unit uses
to recognise the key and allow ignition.
OPERATION
Each time the car is started by turning the ignition key
to MAR, the Lancia CODE system control unit sends an
acknowledgement code to the engine control unit to de-
activate the inhibitor.
The code is sent only if the control unit of the Lancia
CODE system has acknowledged the code received from
the key.
Each time the ignition key is turned to STOP, the Lancia
CODE system deactivates the functions of the electronic
engine control unit.
If the code is not recognised correctly during ignition, the
Ywarning light (or symbol in the display) comes on.In this case turn the key to STOP and then to MAR; if
the lock persists try again with the spare set of keys. Con-
tact a Lancia Dealership if you still cannot start the en-
gine.
IMPORTANT Each key has its own code which must be
stored by the system control unit. To have new keys mem-
orised (up to a maximum number of eight keys), contact
a Lancia Dealership and be ready to present all the keys
you have at present, the CODE card, a personal identity
document and the car ownership documents. The codes
of any keys not presented during the memorising proce-
dure will be deleted. This is to prevent lost or stolen keys
from starting the engine.
Ywarning light (or symbol in the display) lit up
during driving
If the Ywarning light (or symbol in the display)
comes on, this means that the system is running a self-
diagnosis test (caused, for example, by a voltage drop).
If the Ywarning light (or symbol in the display) remains
on, contact a Lancia dealership.
The electronic components inside the key may
be damaged if the key is submitted to sharp
knocks.

42GETTING TO KNOW YOUR CAR
IMPORTANT The engine inhibitor function is guaranteed
by the Lancia CODE, which is automatically activated
when the ignition key is extracted from the starter de-
vice.
SWITCHING ON THE ALARM
With the doors and bonnet closed and the ignition key
either turned to STOP or removed, point the key with the
remote control towards the vehicle and press and release
button
Á.
Excluding some versions for specific markets, the system
produces an acoustic warning (beep) and enables door
locking.
Before the alarm is enabled, a self-diagnosis test is run:
if a fault is detected, the system emits another sound warn-
ing and a message is shown on the display, (see “Instru-
ment panel warning lights”).
In this case switch off the alarm by pressing
Ë, check that
all the doors, bonnet and tailgate are closed correctly; then
switch the alarm back on by pressing
Á.
If a door or the bonnet is not correctly closed, it will be ex-
cluded from the testing by the alarm system.
If the alarm produces an acoustic signal even when the
doors, bonnet and tailgate are correctly closed, a failure
has occurred in system operation. Contact a Lancia Deal-
ership.IMPORTANT Centrally locking the doors using the met-
al insert on the key does not activate the alarm.
IMPORTANT Originally, the alarm is configured in com-
pliance with the regulations existing in the different coun-
tries.
SWITCHING OFF THE ALARM
Press button
Ëon the key with the remote control.
The following operations are performed (excluding some
versions for specific markets):
the direction indicators flash twice;
two brief acoustic signals are emitted (“BEEP”);
the doors are unlocked.
IMPORTANT If the central door locking system is re-
leased using the metal insert of the key, the alarm is not
disabled.

GETTING TO KNOW YOUR CAR63
1
LANE CHANGE FUNCTION
If you want to signal that you are changing lane, hold the
left-hand lever in the unstable position for less than half
a second. The direction indicator on the selected side flash-
es 5 times and then switches off automatically.
“FOLLOW ME HOME” DEVICE
This function allows the space in front of the car to be lit
up for a preset period of time.
Activation
With the ignition key on STOP or removed, pull the lever
towards the steering wheel within 2 minutes of switching
the engine off. The amount of time the lights remain on
is extended by 30 seconds at each movement of the lever,
up to a maximum of 210 seconds; after this the lights are
switched off automatically. Each time the lever is oper-
ated, the warning light on the instrument panel comes
on and the display shows how long the function will re-
main active. The warning light comes on the first time the
lever is operated, and stays on until the function is auto-
matically deactivated. Each time you operate the lever, the
amount of time the lights will remain lit up increases.
Deactivation
Keep the lever pulled towards the steering wheel for more
than 2 seconds.WINDOW WASHING
The right-hand lever fig. 29 controls windscreen
wiper/washer and heated rear window wiper/washer op-
eration.
WINDSCREEN WIPER/WASHER fig. 29
This only operates with the ignition turned to MAR.
The right-hand lever can take five different positions:
A: windscreen wiper off.
B: intermittent operation;
With the lever in position B, turn selector wheel F to se-
lect one of four different speeds for the intermittent op-
eration mode:
,= very slow intermittent operation
= slow intermittent operation.
= normal intermittent operation
= fast intermittent operation.
C: continuous slow operation;
D: continuous fast operation;
E: temporary fast operation (unstable position).

GETTING TO KNOW YOUR CAR65
1
fig. 30L0E0023m
The rear window wiper stops operating a few strokes af-
ter the lever is released; after a few seconds, a further
cleaning stroke completes the wiping operation.
RAIN SENSOR (where provided)
The rain sensor A-fig. 30 is located behind the interior
rear-view mirror in contact with the windscreen and au-
tomatically adjusts the frequency of the windscreen wiper
strokes according to the rain intensity during intermittent
operation.
The sensor has an adjustment range that varies progres-
sively from wiper still (no stroke) when the windscreen
is dry, to wiper at first continuous speed (slow continu-
ous operation) with intense rain.Activation
Move the right lever down by one click.
The activation of the rain sensor is signalled by a com-
mand acquisition stroke.
IMPORTANT Keep the glass in the sensor area clean.
By turning selector wheel F-fig. 29 is it possible to increase
the sensitivity of the rain sensor to obtain a more rapid
variation between wiper still (no stroke) when the wind-
screen is dry, to wiper at first continuous speed (slow con-
tinuous operation).
The increase in the sensitivity of the rain sensor is signalled
by a control and acquisition “stroke”.
When the windscreen washer is operated with the rain sen-
sor activated, the normal washing cycle is performed, at
the end of which the rain sensor resumes its normal au-
tomatic function.

GETTING TO KNOW YOUR CAR67
1
When travelling downhill with the device engaged, the car
speed may exceed the memorised one.
The engagement of the device is signalled by the Üwarn-
ing light lighting up in the instrument panel (together with
a message shown on the display) (see “Instrument panel
warning lights” in chapter 1).
MEMORISING VEHICLE SPEED
Proceed as follows:
turn selector wheel A-fig. 31 to ON and press the ac-
celerator until the vehicle reaches the desired speed;
turn selector wheel B to (+) for at least three seconds
and then release it: the car speed will be memorised
and the accelerator pedal may be released.
If required (e.g. for overtaking), press the accelerator ped-
al to accelerate: the car will return to the previously set
speed when the pedal is released.
RESTORING MEMORISED SPEED
If the device has been disengaged, for example by press-
ing the brake or clutch pedal, the memorised speed can
be reset as follows:
accelerate gradually until you reach a speed ap-
proaching the one memorised;
engage the gear selected at the time of speed memo-
rising (4th, 5th or 6th gear);
press button C-fig. 31.INCREASING THE MEMORISED SPEED
This can be carried out in two ways:
by pressing the accelerator and then memorising the
new speed reached;
or
by temporarily turning selector wheel B-fig. 31 to (+).
Each movement of the selector wheel will correspond to
a slight increase in speed (about 1 km/h), while keeping
the selector wheel turned will correspond to a continuous
speed increase.
REDUCING THE MEMORISED SPEED
This can be carried out in two ways:
by disengaging the device and then memorising the
new speed;
or
by keeping selector wheel B-fig. 31 turned to (–) un-
til the new speed is reached; it will then be memorised
automatically.
Each movement of the selector wheel will correspond to
a slight reduction in speed (about 1 km/h), while keep-
ing the selector wheel turned will correspond to a contin-
uous reduction in speed.

104GETTING TO KNOW YOUR CAR
DRIVING ADVISOR(where provided)
The Driving Advisor is a warning system that notifies
the driver if they drift out of their lane because they
have been distracted.
A video sensor, fitted to the windscreen near the internal
rear-view mirror, detects the lane boundaries and the ve-
hicle’s position in respect to them.
IMPORTANT If the windscreen needs replacing on cars
fitted with a Driving Advisor system, it is advisable to go
to a Lancia Dealership. If the repair is being carried out
at a specialist window replacement centre, it is still nec-
essary to go to a Lancia Dealership to have the tv cam-
era calibrated.
OPERATION
The system is not activated when the vehicle is started.
It is only activated when button A-fig. 70 on the dash-
board is pressed. Activation is confirmed by the lighting
up of the LED on the button and a dedicated message ap-
pearing on the display. Once it is turned on the system will
recognize the operating conditions which is signalled to
the driver by the LED located in the button flashing and
the symbol
ein the amber coloured panel in the instru-
ment panel display flashing too. Once the system has
recognised the operating conditions, it becomes active.
When this happens: the
eicon on the display goes out
and the LED on the button remains on constantly. IMPORTANT If the operating conditions are no longer
present then the system will deactivate. This is signalled
to the driver by: the LED on the button and the amber
eicon on the display flashing.
OPERATING CONDITIONS FOR ACTIVATION
Once switched on, the system becomes active only if the
following conditions are present:
always keep at least one hand on the steering wheel;
vehicle speed between 65 km/h and 180 km/h;
presence of lane demarcation lines not deteriorated and
visible on both sides;
suitable visibility conditions;
straight road or wide curves;
visual field condition sufficient (safety distance from
vehicle in front).
ACTIVATING/DEACTIVATING THE SYSTEM
When the system is active, if the vehicle nears one of the
side lane markings a torque is applied to the steering wheel
advising the driver of the direction the steering wheel needs
to the turned to stay in the present lane.
If the driver turns on the direction indicator in order to
change lanes or for overtaking, then the system will switch
off momentarily. If the driver wishes to change lanes with-
out turning the direction indicator on, then there will be
a warning from the steering wheel that they are about to
cross the line. If the driver continues with the manoeuvre
to change lanes, the system will be temporarily deactivated
and then switch back on again once it has recognized the

GETTING TO KNOW YOUR CAR105
1
new driving lane. This temporary deactivation will be sig-
nalled to the driver by the LED in the button flashing and
by the symbol
ein the amber coloured panel in the in-
strument panel display also flashing.
SWITCHING OFF THE SYSTEM
Manual method
The system can be deactivated by pressing button A-fig.
70 on the dashboard.
Confirmation of system deactivation is signalled by the
LED on the button going out and a message 1-fig. 71 ap-
pearing on the display.
Automatic method
The system can be deactivated automatically (if the sys-
tem is required it will therefore need to be reactivated).
The driver is advised that the system has been turned off au-
tomatically by three consecutive acoustic signals and the mes-
sage 1 – fig. 71 in the instrument panel display after the fol-
lowing situations:
the driver does not keep his hands on the steering wheel
(indication 2-fig. 71 is shown on the instrument pan-
el and a buzzer sounds until the driver places his hands
back on the wheel. This is considered a dangerous con-
dition and the system is automatically deactivated);
triggering of the vehicle safety systems (ABS, ESP,
ASR, DST and TTC).SYSTEM FAILURE
In the event of a malfunction, the system reports the fault
via a message 3-fig. 71 appearing on the display and a
buzzer sounding.
IMPORTANT
The driving advisor is unable to operate following a malfunc-
tion in any of the following safety systems: ABS, ESP, ASR,
DST and TTC.
In the presence of indistinct, overlapping or
missing lane markings, the lane assistance
function is unable to aid the driver and the
system will be deactivated.
The driving advisor is not an automatic dri-
ving system and cannot replace the driver in
controlling the vehicle trajectory. The driver
is personally responsible for maintaining a suitable
level of concentration as traffic and road conditions
require, and for safely controlling the vehicle’s tra-
jectory.
The operation of the lane assistance function may be com-
promised by adverse visibility conditions (rain, fog, snow),
extreme lighting conditions (solar glare, darkness) or dirt
or damage, even partial, to the windscreen in the area
around the video camera.
The area of the windscreen by the TV camera should not
be partly or totally obscured by objects (e.g. stickers, pro-
tective film, etc.)

GETTING TO KNOW YOUR CAR107
1
System not activated
The system searches
for the operating
conditions
System activated
and operating
conditions recognised
The system has been turned
on and is activated
The system has been turned
off manually
The system has been turned
off automatically
The system warns the
driver to place their hands
on the steering wheel
The system is faulty:
go to a
Lancia Dealership
TABLE SUMMARIZING SIGNALS DURING THE USE OF THE DRIVING ADVISOR
–
–
–
–
–
3 signals
Intermittent
warning
Single
and prolonged
warning–
Lit up, flashing
–
–
–
–
Lit up, constantly
Lit up, constantly –
–
–
fig. 70
1 - fig. 71
1 - fig. 71
2 - fig. 71
3 - fig. 71
Status of the LED Message Status of the warning lightAcoustic Meaning
in the button in the display in the instrument panel signal
Off
On, flashing
On, constantly
On, constantly
Off
Off
On, flashing
Off