dashboard warning lights Lancia Musa 2009 Owner handbook (in English)

147
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
Versions with alloy rims
❒Ensure that the surfaces in contact
with the hub are clean;
❒install the standard wheel by fit-
ting it on the centring pins. Fit the
fastening bolts and screw them
down using the wrench provided;
❒lower the car and remove the jack;
❒using the wrench provided, fully
tighten the bolts in the sequence
shown in fig. 15for the small
spare wheel;
❒refit the snap-fitted hub cap.When you have finished
❒stow the spare wheel in the space
provided in the boot;
❒ fit the jack partially open in its
box, forcing it lightly to prevent it
from vibrating when travelling;
❒put the tools back into their places
in the container;
❒stow the container, complete with
tools, into the spare wheel, screw-
ing in the locking device;
❒put the boot’s stiff preformed in-
sulating mat back in position.WHEN NEEDING
TO CHANGE
A BULB
GENERAL INSTRUCTIONS
❒When a bulb is not working, check
that the corresponding fuse is in-
tact before replacing it: refer to the
“If a fuse blows” paragraph in this
chapter for fuse location;
❒Before changing a bulb check the
contacts for oxidation;
❒burnt bulbs must be replaced by
others of the same type and power;
❒For safety reasons, always check
the height of the headlight beam
after changing a bulb.
Halogen lamps must be han-
dled holding the metallic
part only. Touching the
transparent part of the bulb
with your fingers may reduce the in-
tensity of the emitted light and even
compromise duration of the lamp it-
self. In the event of accidental contact,
rub the bulb with a cloth dampened
with alcohol and allow to dry.
135-164 MUSA 1ed GB 10-07-2008 9:38 Pagina 147

148
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
Changes or repairs to the
electrical system (electric
control units) carried out incorrectly
and without due consideration for
the technical specifications of the
system can lead to malfunctioning
and generate a fire hazard.
WARNING
Halogen lamps contain gas
under pressure. Their
breaking can cause scattering of
glass fragments.
WARNING
BULB TYPES fig. 16
Various types of bulbs are fitted to
your car:
A All glass bulb: clipped into place.
Pull to extract.
B Bayonet bulbs: to remove this type
of bulb from its holder, press the
bulb and turn it anticlockwise.
C Cylindrical bulbs: release from the
contacts to extract.
D-E Halogen bulbs: release the fas
tening clip from the correspond
ing seat to remove the lamp.
L0D0178mfig. 16
The rear sidelights and
brake lights and the third
brake light are LEDs so in the event
of malfunctioning, contact a Lancia
Dealership.
WARNING
IMPORTANT A slight misting may ap-
pear on the internal surface of the
headlight: this does not indicate a fault
and is caused by low temperature and
the degree of humidity in the air. Mist-
ing will rapidly disappear when the
headlights are switched on. The pres-
ence of drops inside the headlights in-
dicates infiltration of water. Contact a
Lancia Dealership
135-164 MUSA 1ed GB 10-07-2008 9:38 Pagina 148

149
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
BulbRef. figure TypePower
Main beam headlightsEH3 55W
Dipped beam headlights DH7LL 55W
Front sidelights AW5WLL 5W
Front fog lights (where provided)EH1 55W
Front direction indicators (orange)BPY21W 21W
Side direction indicators AWY5W 5W
Rear direction indicatorsBPY21W 21W
Reversing lights BP21W 21W
Rear fog lights BP21W 21W
Number plate lights CC5W 5W
Front light AW5W 10W
Rear lightAW5W 10W
Rear lights (in presence of sun roof)AW5W 5W
Boot light AW5W 5W
135-164 MUSA 1ed GB 10-07-2008 9:38 Pagina 149

150
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
IF AN EXTERIOR
LIGHT BURNS OUT
For the type of bulb and power rat-
ing, see “When needing to change a
bulb”.
FRONT LIGHT CLUSTERS
The front light clusters contain side-
lights, dipped beam, main beam and
direction indicator bulbs.
To replace the bulbs in the sidelights,
dipped beam and main beam lights,
remove the protective caps.The bulbs are arranged inside the
light unit fig. 17:as follows:
Cdirection indicators
Dmain beam
Bsidelights
Fdipped beam
After replacing the bulbs, put the
protective caps for the lights changed
back into position and ensure that
they are effectively locked into place.IMPORTANT To access the bulb
holder of the left headlight (direction
of travel) in order to replace it, first
remove the protective cover B-fig. 18
of the fuse box in the engine com-
partment.
fig. 17L0D0398mfig. 18L0D0125m
135-164 MUSA 1ed GB 10-07-2008 9:38 Pagina 150

151
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
DIPPED BEAM HEADLIGHTS
fig. 19-20
To change the bulb, proceed as fol-
lows:
❒remove the protective caps;
❒turn the bulb holder unit Ain an
anticlockwise direction and re-
move it from its seat;
❒disengage the two tabs Bfrom the
retaining device, remove the bulb
Cand replace it;❒remount the bulb holder unit Ain
its seat and turn it in a clockwise
direction;
❒after replacing the bulbs, put the
protective caps back into position;MAIN BEAM LIGHTS fig. 21
To change the bulb, proceed as fol-
lows:
❒remove the protective caps;
❒release the bulb holding clip A;
❒disconnect the electric connector
B;
❒remove the bulb Cand replace it;
❒fit the new bulb, ensuring that the
outline of the metal part coincides
with the grooves on the curve of
the headlight. Then reconnect the
electrical connector Band reattach
the bulb holding clip A;
❒after replacing the bulbs, put the
protective caps back into position.
fig. 20L0D0401mfig. 21L0D0402mfig. 19L0D0400m
135-164 MUSA 1ed GB 10-07-2008 9:38 Pagina 151

152
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
fig. 22L0C0403m
DIRECTION INDICATORS
Front fig. ›22‹
To change the bulb, proceed as fol-
lows:
❒turn the bulb holder Ain an anti-
clockwise direction and remove it;
❒remove the bulb Bby pushing it
slightly and turning it in an anti-
clockwise direction (“bayonet”);
❒replace the bulb;
❒refit the bulb holder by turning it
clockwise and locking it properly.Sidelights fig. 23
To change the bulb, proceed as fol-
lows:
❒prise at the point indicated by the
arrow, so as to compress the fixing
clip and extract the assembly C;
❒turn the bulb holder anticlockwise
D, remove the snap-fitted bulb
and replace it;
❒reinstall the bulb holder Din the
lens, then install the assembly
making sure that the fixing clip
has clicked.FRONT SIDELIGHTS fig. 24
To replace the bulbs proceed as fol-
lows:
❒remove the protective caps;
❒remove the snap-fitted bulb holder
A, remove the bulb Band replace it;
❒refit the snap-fitted bulb holder A;
❒after replacing the bulbs, put the
protective caps back into position.
fig. 23L0C0148mfig. 24L0C0405m
135-164 MUSA 1ed GB 10-07-2008 9:38 Pagina 152

153
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
FRONT FOG LIGHTS
(where provided) fig. 25
To replace a fog light bulb, contact a
Lancia Dealership.
fig. 25L0D0406m
REAR LIGHT CLUSTERS
The rear headlights use LED lighting
technology for the sidelights and
brake lights. In the event of malfunc-
tioning, contact a Lancia Dealership.
To change the bulb in the direction in-
dicators, proceed as follows:
❒open the tailgate;
❒turn the fastening device Ain an
anticlockwise direction (for the
left-hand door) or in a clockwise
direction (for the right-hand door)
and remove the covering door;
❒disconnect the electric connector
C;
❒unscrew the two fastening nuts B;
❒to remove the headlight, pull it up
perpendicularly using the handle
on the body of the headlight itself;
❒press down the bulb holder lock-
ing tabs and extract it from its
seat;
❒remove the bulb by pushing it
slightly and turning it in an anti-
clockwise direction;
❒reinstall the bulb holder ensuring
that the two locking tabs are effec-
tively engaged; fit the light unit in
its housing and hook up the elec-
trical connector C; tighten the two
fastening nuts B; refit the coveringdoor taking care to insert the tabs
in their seat and turning the fas-
tening device Ain an anticlockwise
direction (for the left-hand door) or
in a clockwise direction (for the
right-hand door) in order to engage
it.
fig. 26L0D0187m
fig. 27L0D0188m
135-164 MUSA 1ed GB 10-07-2008 9:38 Pagina 153

154
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
THIRD BRAKE LIGHTS
The 3rd brake light uses LED light-
ing technology. In the event of mal-
functioning, contact a Lancia Dealer-
ship.
fig. 28L0D0407m
NUMBER PLATE LIGHTS fig. 29a
To replace the bulbs proceed as fol-
lows:
❒work in the point shown by the
arrow and remove lens A;
❒change the bulbBreleasing it
from the side contacts and making
sure the new bulb is correctly fas-
tened between the contacts;
❒reinstall the lens.
fig. 29/aL0D0357mfig. 29/bL0D0426m
fig. 29/cL0D0427m
REAR FOG LIGHTS fig. 29/b
Contact Lancia Dealership to have
rear fog lights replaced.
REVERSING LIGHTS fig. 29/c
Contact Lancia Dealership to have re-
versing light replaced.
135-164 MUSA 1ed GB 10-07-2008 9:38 Pagina 154

155
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
fig. 30L0D0193m
fig. 31L0D0194m
IF AN INTERIOR
LIGHT BURNS OUT
For the type of bulb and power rat-
ing, see “When needing to change a
bulb”.
FRONT LIGHT fig. 30-31
To replace the bulbs proceed as fol-
lows:
❒work in the points shown by the
arrows and remove light A;
❒open the protection lid B;
❒replace bulbs Creleasing them
from the side contacts; make sure
that new bulbs are correctly
clamped between contacts;
❒re-close the lid Band secure light
Ainto its housing locking it prop-
erly.
REAR LIGHT fig. 32-33
To replace the bulbs proceed as fol-
lows:
❒work in the points shown by the
arrows and remove light D;
❒open the protection lid E;
fig. 32L0D0195m
❒change the bulb Freleasing it from
the side contacts and making sure
the new bulb is correctly fastened
between the contacts;
❒re-close the protection lid Eand
refit light Dinto its housing lock-
ing it properly.
fig. 33L0D0196m
135-164 MUSA 1ed GB 10-07-2008 9:38 Pagina 155

156
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
BOOT LIGHT fig. 34
To change the bulb, proceed as fol-
lows:
❒open the tailgate;
❒remove the light Alevering in the
point shown by the arrow.
❒open the protection Band replace
the snap-fitted bulb;
❒re-close the protective cover Bon
the lens;
❒refit the light Ainserting it in its
correct position firstly on one end
and then on the other until it
clicks into place.
fig. 34L0D0197m
IF A FUSE BLOWS
GENERALITIES fig. 35
The fuse is a protective device for the
electric system: it comes into action
(i.e. it cuts off) mainly due to a fault
or improper action on the system.
Check the efficiency of the corre-
sponding fuse when a device does not
work: the conducting element Amust
not be interrupted. If it is, replace the
blown fuse with another with the
same amperage (same colour).
B: intact fuse.
C: fuse with damaged filament.
To replace a fuse use the pliers Dat-
tached to the fuse box on the instru-
ment dashboard.
fig. 35L0D0198m
If the fuse should fail again,
contact a Lancia Dealer-
ship.
WARNING
Never change a fuse with an-
other with a higher amp rat-
ing; DANGER OF FIRE.
If a general fuse (MEGA-
FUSE,MIDI-FUSE, MAXI-
FUSE) cuts in, contact a Lancia Deal-
ership.
WARNING
Before changing a fuse,
check that the ignition key
has been removed and that all the
other electric devices have been
turned off/disabled.
WARNING
135-164 MUSA 1ed GB 10-07-2008 9:38 Pagina 156