warning lights Lancia Musa 2009 Owner handbook (in English)

185
WARNING
LIGHTS AND
MESSAGES
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
MAINTENANCE
AND CARE
Engine compartment
At the end of the winter the engine
compartment should be carefully
washed, without directing the jet
against electronic control units. Have
this operation performed at a spe-
cialised workshop.
IMPORTANT Perform this operation
on a cold engine and with the key at
STOP. After the washing operation,
make sure that the various protections
(e.g. rubber caps and guards) have
not been removed or damaged.
Never use flammable prod-
ucts, such as petrol ether or
rectified petrol to clean inside the
car. The electrostatic charges which
are generated by rubbing during the
cleaning operation may cause a fire.
WARNINGINTERIORS
Periodically check that water is not
trapped under the mats (due to water
dripping off shoes, umbrellas, etc.)
which could cause oxidisation of the
sheet metal.
CLEANING SEATS AND FABRIC
PA R T S
Remove dust with a soft brush or a
vacuum cleaner. It is advisable to use
a moist brush on velvet upholstery.
Rub the seats with a sponge moist-
ened with a solution of water and
neutral detergent.
INTERIOR PLASTIC PARTS
It is advisable to clean interior parts
with a moist cloth and a solution of
water and mild soap. Use specific
products for cleaning plastic, without
solvents and specifically designed to
prevent damage to the appearance
and colour of the treated parts to re-
move grease and tough stains.
IMPORTANT Never use spirit or
petroL to clean the glass of the in-
strument panel or other plastic parts.
165-186 MUSA 1ed GB 10-07-2008 9:39 Pagina 185

186
WARNING
LIGHTS AND
MESSAGES
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
MAINTENANCE
AND CARE
Do not keep aerosol cans in
the car: risk of explosion.
Aerosol cans must not be exposed to
a temperature exceeding 50°C.
When the vehicle is exposed to sun-
light, the internal temperature can
greatly exceed this value.
WARNINGSTEERING WHEEL/GEAR
LEVER COVERED
IN REAL LEATHER
These components must be cleaned
with mild soap and water only. Never
use spirit and/or alcohol based prod-
ucts.
Before using specific products for the
cleaning of the interiors, ensure
through careful reading that the in-
structions on the label of the product
do not contain alcohol and/or alcohol-
based substances.
If, during cleaning of the windscreen,
window cleaner accidentally drips
onto the leather of the steering wheel
/ gear lever knob, wipe away imme-
diately and then wash the area with
mild soap and water.
IMPORTANT Be careful when in-
stalling a steering wheel lock device,
where applicable, to prevent damag-
ing the leather upholstery by rubbing.
165-186 MUSA 1ed GB 10-07-2008 9:39 Pagina 186

187
WARNING
LIGHTS AND
MESSAGES
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
TECHNICAL SPECIFICATIONS
IDENTIFICATION DATA .................................. 188
ENGINE CODES -
BODYWORK VERSIONS .................................. 190
ENGINE........................................................... 191
FUEL FEED/IGNITION ................................... 192
TRANSMISSION............................................... 192
BRAKES........................................................... 193
SUSPENSIONS................................................. 193
STEERING....................................................... 193
WHEELS.......................................................... 194
DIMENSIONS................................................... 198
PERFORMANCE.............................................. 199
WEIGHTS........................................................ 200
CAPACITIES .................................................... 201
FLUIDS AND LUBRICANTS ............................ 202
FUEL CONSUMPTION .................................... 204
CO
2EMISSIONS............................................... 205
187-205 MUSA 1ed GB 10-07-2008 9:40 Pagina 187

188
WARNING
LIGHTS AND
MESSAGES
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
IDENTIFICATION
DATA
Take note of the identification codes.
The identification data stamped on
the plates fig. 1and their respective
positions are as follows:
1- Model plate.
2- Chassis marking
3- Bodywork paint identification
plate
4- Engine marking.MODEL PLATE fig. 2
This plate is applied to the engine
compartment front beam and shows
the following identification data:
B- Homologation number.
C- Vehicle type code.
D- Chassis number.
E- Maximum vehicle weight fully
loaded.
F- Maximum vehicle weight fully
loaded plus trailer.G- Maximum weight on front axle.
H- Maximum vehicle weight on rear
axle.
I- Engine type.
L- Body version code.
M- Spare part code.
N- Smoke opacity index (for diesel
engines).
fig. 1L0D0450mfig. 2L0D0415m
187-205 MUSA 1ed GB 10-07-2008 9:40 Pagina 188

189
WARNING
LIGHTS AND
MESSAGES
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
CHASSIS MARKING fig. 3
This is printed on the passenger com-
partment floor bed near the front
right seat.
To access it, lift the opening cut in the
carpet for this purpose; it shows:
❒car model;
❒chassis number.
BODYWORK PAINT
IDENTIFICATION PLATE fig. 4
This plate is applied to the front bon-
net and shows the following data:
A- Paint manufacturer.
B- Colour name.
C- Lancia colour code.
D- Respray and touch up code.ENGINE MARKING
Engine marking is stamped on the
motor block, passenger compartment
side, and includes the model and the
chassis number.
fig. 3L0D0227m
fig. 4L0D0228m
187-205 MUSA 1ed GB 10-07-2008 9:40 Pagina 189

190
WARNING
LIGHTS AND
MESSAGES
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
ENGINE CODES - BODYWORK VERSIONS
Versions
1.4
8V(▲)
1.416V
1.416V90HP (▲)
1.3 Multijet 70HP
1.3 Multijet 90HP
1.6 Multijet
1.6 Multijet 115HP (▲)
1.9 Multijet 100HP (▲)
(▲) Engine provided for some versions/markets only
(*) For specific markets
(
❒) DPF versionEngine code
350A1000
843A1000
192B2000
188A9000
199A3000
350A2000
350A3000
188B2000Bodywork code
350 AXF1A08 EL (5 seats)
350 AXF1A08 FL (4 seats)
350 AXA1B07 GL
350 AXE1A06 CL
350 AXB1A01 QL (5 seats)
350 AXG1A09 AEL (5 seats)
350 AXG1A09 AFL (4 seats)
350 AXG1A09 AGL (5 seats) (*)
350 AXG1A09 AHL (4 seats) (*)
350 AXH1A11 CL (5 seats) (*)
350 AXH1A11 DL (4 seats) (*)
350 AXL1A12 CL (5 seats) (*)
350 AXL1A12 DL (4 seats) (*)
350 AXC1A02 LL
187-205 MUSA 1ed GB 10-07-2008 9:40 Pagina 190

191
WARNING
LIGHTS AND
MESSAGES
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
1.3 Multijet 70HP
188A9000
Diesel
4 in line
4
69.6 x 82
1248
18±0.4
51
70
4000
180
18,3
1750
–
Diesel fuel for
motor vehicles
(Specification
EN590)
1.48V(▲)
350A1000
Otto
4 in line
2
72 x 84
1368
11±0.2
57
77
6000
115
11,7
3000
NGK ZKR7A-10
Unleaded petrol
95 RON
(Specification
EN228)1.416V
843A1000
Otto
4 in line
4
72 x 84
1368
11±0.2
70
95
5800
128
13
4500
NGK ZKR7A-10
Unleaded petrol
95 RON
(Specification
EN228)
ENGINE
INTRODUCTION
Engine code:
Cycle:
Number and layout of cylinders:
Number of valves per cylinder:
Piston bore and stroke mm:
Total displacement cm3:
Compression ratio:
Maximum power (EEC) kW
HP
corresponding ratio: rpm
Maximum torque (EEC) Nm
kgm
corresponding ratio: rpm
Spark plugs:
Fuel:
(▲)Engine provided for some versions/markets only
1.6 Multijet
350A200
Diesel
4 in line
4
79.5 x 80.5
1598
16,5±1
88
120
3500
300
30,5
1500
–
Diesel fuel for
motor vehicles
(EN590
specifications) 1.3 Multijet 90HP
199A3000
Diesel
4 in line
4
69.6 x 82
1248
17,6±0.4
66
90
4000
200
20
1750
–
Diesel fuel for
motor vehicles
(Specification
EN590)
187-205 MUSA 1ed GB 10-07-2008 9:40 Pagina 191

192
WARNING
LIGHTS AND
MESSAGES
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
Modifications or repairs to the fuel feed system that are not carried out properly or do not take the system’s
technical specifications into account can cause malfunctions leading to the risk of fire.
(▲) Engine provided for some versions/markets only
FUEL FEED/IGNITION
Fuel feed/ignition
1.48V(▲)-1.416V
Multipoint phased sequential electronic injection,
integrated with ignition,
returnless system1.3 Multijet - 1.6 Multijet
Electronically controlled Multijet “Common Rail”
direct injection, with turbo
and intercooler
TRANSMISSION
Gearbox
Clutch
Drive1.4
16V
Five or six forward gears plus reverse
with synchronisers for forward gears
Self-adjusting external hydraulic control
with pedal without loadless stroke
Fr
ont
1.48V(▲)-1.3 Multijet - 1.6 Multijet
Five forward gears plus reverse
with synchronisers for forward gears
Self-adjusting external hydraulic control
with pedal without loadless stroke
Fr
ont
187-205 MUSA 1ed GB 10-07-2008 9:40 Pagina 192

193
WARNING
LIGHTS AND
MESSAGES
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
BRAKES
Service brakes:
– front
– rear
Parking brake
IMPORTANT Water, ice and salt sprinkled on roads can deposit on the brake discs and reduce the braking efficiency when braking for
the first time.1.4
8V(▲)-1.416V- 1.3 Multijet 70HP
Self-ventilating discs (257 mm x 22 mm)
Drum (203 mm x 38 mm)
Controlled by hand lever, acting
on rear brakes
SUSPENSIONS
Front
Rear1.4
8V(▲)-1.416V- 1.3 Multijet - 1.6 Multijet
Mc Pherson independent wheels
Semi-independent wheels connected by crank axle
STEERING
Type
Minimum steering
cycle m
(
▲) Engine provided for some versions/markets only1.4
8V(▲)-1.416V- 1.3 Multijet - 1.6 Multijet
Rack and pinion with electric power steering
10.0
1.3 Multijet 90HP - 1.6 Multijet
Self-ventilating discs (284 mm x 22 mm)
1.3 Multijet 90HP: drum (228 mm x 40 mm)
1.6 Multijet: disc (240 mm x 11 mm)
Controlled by hand lever, acting on
rear brakes
187-205 MUSA 1ed GB 10-07-2008 9:40 Pagina 193

194
WARNING
LIGHTS AND
MESSAGES
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
WHEELS
RIMS AND TYRES fig. 5
Pressed steel or alloy rims. Tubeless
radial carcass tyres. All approved
tyres are listed in the Log Book.
IMPORTANT In the event of discrep-
ancies between the information pro-
vided on this “Owner handbook” and
the “Log book”, consider the specifi-
cations shown in the log book only.
Respect the prescribed size to ensure
safety of the car in movement. Fit
tyres of the same make and type on
all wheels.
IMPORTANT Do not use inner tubes
with Tubeless tyres.READING TYRE MARKINGS
Example: 185/65 R 14 86 T
185= Nominal width (S, distance in
mm between sidewalls).
65= Height/width ratio (H/S) in
percentage.
R= Radial tyre.
14= Rim diameter in inches (Ø).
86Load rate (capacity).
T= Maximum speed rating.
fig. 5L0D0229m
SMALL SPARE WHEEL
Pressed steel rim Tubeless tyre.
WHEEL GEOMETRY
Toe-in measured between rims: 0 ±1
mm.
The values refer to the car in running
order.
187-205 MUSA 1ed GB 10-07-2008 9:40 Pagina 194