wheel bolts Lancia Musa 2010 Owner handbook (in English)
[x] Cancel search | Manufacturer: LANCIA, Model Year: 2010, Model line: Musa, Model: Lancia Musa 2010Pages: 218, PDF Size: 3.71 MB
Page 144 of 218
143
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
The spare wheel is specific
for your car. Do not use it
on cars of different models. Do not
use spare wheels of different mod-
els on your car. The space saver
spare wheel must only be used in
case of emergency. Use only for as
long as strictly necessary and drive
at a speed slower than
80 km/h. An orange label is affixed
on the spare wheel summarising
instructions and limitations for
use. Never remove or cover the la-
bel. Never apply a wheel cup on a
space saver spare. The following
information is provided in four
languages on the label: Warning!
Suitable for temporary use only!
80 km/h max! Replace with a
standard wheel as soon as possi-
ble. Do not cover this label.
WARNING
The driving features of the
car may change when a
space saver spare wheel is fitted.
Avoid sudden acceleration and
braking, sudden steering and fast
cornering. The total life of a space
saver spare wheel is approxi-
mately 3000 km, after which it
must be replaced by another wheel
of the same type. Never install a
traditional tyre on a space saver
spare wheel rim. Repair and refit
the standard wheel as soon as pos-
sible. Only one space saver spare
can be used at a time. Do not ap-
ply grease to the bolt threading be-
fore assembly: the bolts could come
loose unexpectedly.
WARNING
The jack may only be used
to replace wheels on the
car which it equips or other cars of
the same model. Never use the jack
for other purposes, such as lifting
other car models. Never use the
jack to carry out repairs under the
car. Incorrect positioning of the
jack may cause the car to fall. Do
not use the jack for loads higher
than those shown on the label.
Snow chains cannot be fitted on a
space saver spare wheel. There-
fore, if a front wheel (drive wheel)
is punctured and you need to use
snow chains, swap with a rear
wheel. In this way, you will have
two normal wheels on the front on
which you can fit snow chains and
solve the emergency.
WARNING
Page 146 of 218
145
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
fig. 11L0D0397m
fig. 12L0D0163m
❒for cars fitting alloy rims, remove
the hub cap using the screwdriver
provided levering in groove E-
fig. 11, as shown in the figure;
❒loosen the bolts of the wheel to be
replaced by about one turn with the
wrench provided E-fig. 12; if the
car is fitted with alloy rims, shake
the car to facilitate removing the
rim from the wheel hub;❒operate the device F- fig. 13to ex-
pand the jack, until the groove G
on the upper part of the jack is
correctly inserted on the lower
edgeHof the body at indication I
(at approximately 60 cm from the
front wheel centre or 80 cm from
the rear wheel centre);
❒warn anybody nearby that the car
is about to be lifted. They must
stay clear and not touch the car
until it is back on the ground;❒fit the handle L-fig. 13to operate
the jack and lift the car until the
wheel to be changed is several cen-
timetres off the ground;
❒for versions with wheel cap, remove
the wheel cap after loosening the
three fastening bolts and finally
loosen the fourth bolt and extract
the wheel;
❒for versions with snap fitted wheel
cup, remove the cup being careful
not to damage it;
❒make sure the contact surfaces be-
tween space saver spare wheel and
hub are clean so that the fastening
bolts will not come loose;
L0D0164mfig. 13
Page 147 of 218
146
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
fig. 14L0D0165mfig. 15L0D0166m
❒fit the space saver spare wheel
making the holes M-fig. 14coin-
cide with the corresponding cen-
tring pins N;
❒using the wrench provided, tighten
the fastening bolts;
❒turn the jack handle to lower the
car and remove the jack;
❒use the wrench provided to fasten
the bolts completely in a criss-cross
fashion as shown in figure. REFITTING THE
STANDARD WHEEL
Following the procedure described
previously, raise the car and remove
the space saver spare wheel.
Versions with steel rims
Proceed as follows:
❒Make sure the contact surfaces be-
tween standard wheel and hub are
clean so that the fastening bolts
will not come loose.
❒Fit the standard wheel by inserting
the first bolt for two threads into
the hole closest to the inflation
valve.❒Fit the wheel cup making the
groove (on the cup) coincide with
the inflation valve and then insert
the other three bolts.
❒For models with snap-on wheel
cup, press the edge of the cup with
the palm of your hands against the
wheel (do not hammer).
❒Using the wrench provided,
tighten the fastening bolts.
❒Lower the car and remove the
jack.
❒using the wrench provided, fully
tighten the bolts in the sequence
shown previously in figure fig. 15.
IMPORTANT Incorrect assembly may
cause the cup to come off while trav-
elling.
Page 148 of 218
147
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
Versions with alloy rims
❒Check that the hub contact sur-
faces are clean;
❒fit the normal wheel centring it on
the pins, lead in the fastening
screws and tighten them using the
wrench provided;
❒lower the car and remove the jack;
❒using the wrench provided, fully
tighten the bolts in the sequence
shown in fig. 15.
❒snap fit the wheel cup on the hub.When you have finished
❒stow the spare wheel in the space
provided in the boot;
❒fit the jack partially open in its
box forcing it lightly to prevent it
from vibrating when travelling;
❒put the tools back into their places
in the container;
❒arrange the container and tools in
the spare wheel and secure the fas-
tening device;
❒rearrange the preformed boot
cover correctly. WHEN NEEDING
TO CHANGE A
BULB
GENERAL INSTRUCTIONS
❒When a bulb is not working, check
that the corresponding fuse is in-
tact before replacing it: refer to the
“If a fuse blows” paragraph in this
chapter for fuse location.
❒before changing a bulb check the
contacts for oxidation;
❒burnt bulbs must be replaced by
others of the same type and power;
❒always check the height of the
headlight beam after changing a
bulb.
Halogen lamps must be
handled holding the metal-
lic part only. Touching the
transparent part of the bulb
with your fingers may reduce the in-
tensity of the emitted light and even
compromise duration of the lamp it-
self.