warning light Lancia Musa 2011 Owner handbook (in English)

65
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
Operation in position Eis limited to
the time during which the lever is
kept in that position manually. When
released, the stalk will return to posi-
tionAand the wiper will be automat-
ically stopped.
IMPORTANT Replace wiper blades as
specified in the “Maintenance and
care” chapter. RAIN SENSOR
(for versions/markets, where provided)
The rain sensor is located behind the
driving mirror in contact with the
windscreen and has the purpose of
automatically adjusting the frequency
of the windscreen wiper strokes as to
the rain intensity.
IMPORTANT Keep clean the glass in
the sensor area.
Activation
Move the right stalk down by one
click.
The activation of the rain sensor is
signalled by a control acquisition
flick.
Turn the ring F-fig. 71to increase the
rain sensor sensitivity.
The increase of the sensitivity of the
rain sensor is signalled by a control
and acquisition flick.
The smart cycle is started when the
windscreen wiper is turned on while
the rain sensor is active without sup-
plementary flick after 5 seconds. The
sensor will resume normal automatic
operation. “Smart washing” function
Pull the stalk towards the steering
wheel (unstable position) to operate
the windscreen washer.
Keeping the stalk pulled for more
than half a second, with just one
movement it is possible to operate the
washer jet and the wiper at the same
time.
The jet will be released immediately
when the wiper stops after four flicks.
A further stroke after 5 seconds com-
pletes the wiping operation. Do not use the windscreen
wiper to remove layers of
snow or ice from the wind-
screen. In such conditions,
the windscreen wiper may be sub-
jected to excessive stress and the
motor protection which prevents op-
eration for a few seconds may trip.
If rear window wiper operation is
not reset, contact a Lancia Dealer-
ship.
fig. 70L0D0074m

66
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
❒in synchronous mode (at half the
frequency of the windscreen
wiper) when the windscreen wiper
is running.
The rear window wiper will run in
continuous mode when the wind-
screen wiper is running and reverse
gear is engaged.
Pull the stalk towards the dashboard
(unstable position) to operate the rear
window washer.
Hold the stalk pushed for longer than
half a second to operate the rear win-
dow wiper as well.
Smart wash function is activated as
for the windscreen wiper when the
stalk is released. The wiper will flick once to indicate
that the sensor has been reactivated.
The rain sensor is able to recognize
and automatically adjust itself in the
presence of the following particular
conditions:
❒dirt on the controlled surface (salt,
dirt, etc.);
❒difference between day and night.
Deactivation
Move the lever from position Bor turn
the ignition key to STOP.
At the next start-up (key at MAR),
the sensor will not be reactivated even
if the stalk is at B. To activate the sen-
sor, move the stalk to position AorC
and then to position Bor turn the sen-
sitivity adjustment knurled ring.
fig. 71L0C0073m
Streaks of water may
cause undesired blade
moving.
WARNING
REAR WINDOW WIPER/
WASHER fig. 72
The device can only work when the
ignition key is at MAR.
Turn ring Afrom position
åto posi-
tion'to open the rear window wiper
as follows:
❒in flick mode when the windscreen
wiper is not running
fig. 72L0D0075m

67
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
CRUISE CONTROL
(for versions/markets, where provided)
It is a device able to support the dri-
ver, with electronic control, which al-
lows driving at speed over 30 km/h
on long and straight dry roads (e.g.:
motorways), at a desired speed, with-
out pressing the accelerator pedal.
Therefore it is not suggested to use
this device on extra-urban roads with
traffic. Do not use it in towns.STORING THE SPEED
Proceed as follows:
❒turn ring A-fig. 73toONand press
the accelerator pedal to the re-
quired speed;
❒push the lever upwards (+) for at
least 3 seconds, then release it: the
car speed will be stored. The ac-
celerator pedal may be released.
If needed (e.g. for overtaking), press
the accelerator pedal to accelerate: the
car will return to the previously set
speed when the pedal is released. TURING THE DEVICE ON
Turn the ring A-fig. 73toON.
The device can only be turned on in
4th or 5th gear. Travelling downhill
with the device engaged, the car speed
may increase more than the memo-
rised one. When the device is acti-
vated the warning light turns on to-
gether with the relevant message on
the instrument panel (for versions/
markets, where provided).
fig. 73L0D0076m

68
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
TURNING THE DEVICE OFF
Turn ring A-fig. 73toOFFor the ig-
nition key to STOP. The device is au-
tomatically turned off in one of the
following cases:
❒when the brake pedal or clutch is
pressed. REDUCING THE STORED
SPEED
This can be carried out in two ways:
❒by turning the device off and then
storing a new speed;
or
❒by moving the stalk downwards
(
–) until reaching the new speed
which will be stored automatically.
Each operation of the stalk will cor-
respond to a slight reduction in speed
(about 1 km/h), while keeping the
stalk downwards will correspond to a
continuous speed reduction. RESTORING THE STORED
SPEED
If the device has been disengaged, for
example by pressing the brake or
clutch pedal, the memorized speed
can be reset as follows:
❒accelerate gradually until reaching
a speed approaching the stored
speed;
❒engage the gear selected when the
speed was stored (4th or 5th gear);
❒press RES B.
INCREASING THE STORED
SPEED
The stored speed can be increased
in two ways:
❒by pressing the accelerator and
then storing the new speed
reached;
or
❒by moving the stalk upwards (
+).
Each operation of the stalk will cor-
respond to a slight increase in speed
(about 1 km/h), while keeping the
stalk upwards will correspond to a
continuous speed increase.
When travelling with the
device on, never set the
gearshift lever to neutral.
WARNING
If the device is faulty, turn
ring A to OFF, check the
fuse and contact a Lancia Dealer-
ship.
WARNING

69
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
CEILING LIGHTS
FRONT CEILING LIGHT
fig. 74
SwitchA-turns these lights on/off .
With switch Ain central position,
lightsCandDwill turn on/off when
opening/closing the front doors.
With switch Apressed on the left side,
lightsCandDwill always stay off.
With switch A-pressed on the right
side, lights CandDwill always stay
on.
The lights will be turned on/off grad-
ually.
SwitchBis used for operating the
spot light function; it works as follows
(light off):
❒lightCif the left side is pressed;
❒lightDif pressed on the right side.Lights when getting into the car
Lights will be turned on as follows:
❒for about 10 seconds when the door
is unlocked;
❒for about 3 minutes when a door is
opened;
❒for about 10 seconds when the
doors are closed (within the three
minutes).
Timing will stop when turning the ig-
nition key to MAR.
Light when getting out of the car
After removing the key from the igni-
tion switch, the lights will turn on as
follows:
❒within 2 minutes from turning the
engine off for about 10 seconds;
❒when a door is opened for about 3
minutes;
❒for about 10 seconds when the
doors are closed (within the three
minutes).
Timing will stop automatically when
locking the doors. IMPORTANT Before getting out of
the vehicle, make sure the switch is at
central position: lights off with doors
closed in order to avoid draining the
battery.
In any case, if the switch is left inad-
vertently to the on position, the lights
will turn off automatically 15 minutes
after turning the engine off.
Courtesy light timing
On certain versions to facilitate get-
ting in/out of the car at night or with
poor lighting, 2 different timed
switching on modes have been pro-
vided.
fig. 74L0D0077m

70
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
Light when getting out of the car
After removing the key from the igni-
tion switch, the lights will turn on as
follows:
❒within 2 minutes from turning the
engine off for about 10 seconds;
❒when a door is opened for about 3
minutes;
❒for about 10 seconds when the
doors are closed (within the three
minutes).
Timing will stop automatically when
locking the doors. Ceiling light timer
(for versions/markets, where provided)
On certain versions to facilitate get-
ting in/out of the car at night or with
poor lighting, 2 different timed
switching on modes have been pro-
vided.
Lights when getting into the car
Lights will be turned on as follows:
❒for about 10 seconds when the door
is unlocked;
❒for about 3 minutes when a door is
opened;
❒for about 10 seconds when the
doors are closed (within the three
minutes).
Timing will stop when turning the ig-
nition key to MAR. REAR COURTESY LIGHT
The light will turn on/off by pressing
the lens rightwards or leftwards
as shown in fig. 75.
The light may be integrated in the
ceiling unit, where provided.
Two 5W ceiling lights fig. 76are pre-
sent if a sunroof is fitted.
fig. 75L0D0078mfig. 76L0D0254m

71
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
HAZARD LIGHTS
EMERGENCY LIGHTS fig. 77-78
Press the toggle switch Ain any posi-
tion of the ignition switch to turn the
lights on.
When the device is on, the switch is
flashing and warning lights Îand¥
on the cluster come on.
Press the switch again to turn the
lights off.
FRONT FOG LIGHTS fig. 79
(for versions/markets, where provided)
To turn front fog lights on, press but-
ton5, to activate these lights it is
necessary to have the side/tail lights
switched on.
Press the button again or turn off the
side/tail lights to turn the lights off.
fig. 77L0D0080m
fig. 78L0D0081m
fig. 79L0D0385m
The use of hazard lights is
governed by the Highway
Code of the country you are in.
Keep to the rules.
WARNINGREAR FOG LIGHTS fig. 80
Press button
4to turn on with the
dipped beam or fog lights on.
Press the button again or turn off the
dipped beam headlights or the fog
lights to turn the lights off.
fig. 80L0D0386m

72
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
FUEL CUT OFF
SWITCH
The switch is located on the bottom of
the car, near the pillar on passenger
side. Move the carpet aside to reach
the switch. It is tipped by a crash and
cuts off the fuel feed, thus stopping
the engine.
When the device is activated the
warning light
èturns on together
with the relevant message on the re-
configurable multifunctional display
(for versions/markets, where pro-
vided).
Inspect the car carefully for fuel leak-
ages (e.g. in the engine compart-
ment), under the car or near the fuel
tank.
If, after a crash, you smell
fuel or see leaks from the
fuel system, do not reset the switch
to avoid fine risk.
WARNING
fig. 81L0D0388m
Press button A-fig. 81to reactivate
the fuel feed system if no leakage is
found and the car is worthy of re-
suming travel.
After the accident, remember to turn
the ignition key to STOPto prevent
draining the battery.

73
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
INTERIOR
EQUIPMENT
UPPER ODDMENT
COMPARTMENTS fig. 82-83
To open the compartments, release
the lid using device Aand lift to the
stable opening position.
CompartmentC-fig. 86and the DIN
compartmentD-fig. 86, in the dash-
board, are located in central position.
The DIN compartment Dcan be ex-
tracted to fit a Lineaccessori Lancia
sound system.
fig. 82L0D0389m
fig. 83L0D0087m
Do not travel with the
compartments open: they
could cause injury in case of an ac-
cident.
WARNING
fig. 84L0D0088m
fig. 85L0D0418m
fig. 86L0D0090m
ODDMENT COMPARTMENTS
CompartmentA-fig. 84is located on
the dashboard facing the front pas-
senger.
CompartmentAmay contain an ex-
tractable oddment bag E-fig. 87
which can be ordered from Lineac-
cessori Lancia.
CompartmentB-fig. 85is located on
the dashboard on the left of the steer-
ing wheel.

74
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
ODDMENT SHELF
ON ROOF fig. 91
The shelf is designed to contain eas-
ily retrievable light items (e.g. papers,
maps, etc.).
IMPORTANT Do not place heavy ob-
jects on the shelf. Do not use it as a
grip.
The shelf is alternative to the sunroof.
CUP HOLDER –
CAN HOLDER fig. 89
The cup/can holders – are located on
the central tunnel near the hand-
brake.
CARD HOLDER fig. 90
The central tunnel has recesses to
keep telephone cards, magnetic cards
and tickets. DOOR POCKETS fig. 88
Paper/map pockets are located in
door panels.
fig. 87L0D0343m
fig. 88L0D0153m
fig. 89L0D0091m
fig. 90L0D0092m
fig. 91L0D0093m