turn signal Lancia Ypsilon 2011 Owner handbook (in English)

If the set distance unit is "km", the fuel
consumption unit will be displayed in km/l or
l/100 km. If the distance unit of measurement
stored is "mi," the display shows the amount of
fuel consumed in "mpg".
❒press
or
to make your choice;
❒when you select “Temperature”, pressing the
button
briefly makes "°C" or "°F" appear
on the display depending on the previous
setting;
❒pressor
to make your choice;
Once the required settings are made, briefly press
button
to go back to the submenu screen or
hold the button down to return to the main menu
screen without storing.
Hold down the
button again to return to the
standard screen or to the main menu according to
where you are in the menu.
Language (Language selection)
Display messages can be shown in the following
languages: Italian, English, German, Portuguese,
Spanish, French, Dutch, Polish. Turkish and
Brazilian.
To set the desired language, proceed as follows:
❒briefly press the button
: the previously set
language starts flashing on the display;❒press
or
to make your choice;
❒press the
button briefly to return to the menu
screen or give the button a long press to return
to the standard screen without storing.
Warnings volume (Adjusting the alert/warning
acoustic signal volume)
With this function the volume of the buzzer which
accompanies the display of any failure/warning
can be adjusted according to 8 levels.
To set the desired volume, proceed as follows:
❒press thebutton briefly, making the display
flash the previously set volume level;
❒pressor
to make your choice;
❒press the
button briefly to return to the menu
screen or give the button a long press to return
to the standard screen without storing.
Button volume (Adjusting the button volume)
With this function it is possible to adjust (to eight
levels) the volume of the acoustic signal emitted
when thebutton is held down to exit a submenu
and return to the standard menu
To set the desired volume, proceed as follows:
❒press thebutton briefly, making the display
flash the previously set volume level;
17GETTING TO
KNOW YOUR CARSAFETY
STARTING
AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

❒press the button
or
to adjust the
volume; an acoustic signal equal to the volume
level being selected is emitted during this
adjustment;
❒press the
button briefly to return to the menu
screen or give the button a long press to return
to the standard screen without storing.
On versions with reconfigurable multifunction
display, the volume level is represented by bars.
Belt buzzer (Buzzer activation for SBR
indication)(for versions/markets, where
provided)
This function can only be displayed after a Lancia
Dealership has deactivated the SBR system (see
"SBR system" in the "Safety" chapter).
Service (Scheduled servicing)
Using this function you can display information
about the mileage or daily intervals for car
servicing. With the Service function it is also
possible to view the interval (in kilometres or
miles) before the next engine oil change is due.
To consult this display, proceed as follows:
❒briefly press the
button, which makes the
display show the service interval in km or mi
according to the previous setting (see "Distance
units of measurement" paragraph);
❒briefly press button
to return to the menu
screen or hold it down to return to the standard
screen.NoteThe "Scheduled Servicing Plan" requires the
car to be serviced every 30,000 km (or 18,000
miles). This is automatically displayed, when the
ignition key is turned to MAR, from 2,000 km
(or the equivalent in miles) and reappears every
200 km (or the equivalent in miles). Below 200
km servicing indications are more frequent. The
display will be in kilometres or miles depending
on the measurement unit settings. When the next
scheduled service is approaching, the message
"Service" will appear on the display, followed by
the number of kilometres or miles left, when
the key is turned to MAR. Contact a Lancia
Dealership where the operations of the "Scheduled
Servicing Plan" will be performed and the
message will be reset.
Passenger airbag (Passenger front and side
airbag activation/deactivation (Side Bag)
This function allows the passenger airbag to be
activated / deactivated.
Proceed as follows:
❒press the
button and, after the message "Bag
pass: Off" (to deactivate) or "Bag pass: On" (to
activate) is displayed by pressing buttons
and
, press the
button again;
❒a confirmation request message will appear on
the display;
18GETTING TO
KNOW YOUR CAR
SAFETY
STARTING
AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

THE LANCIA CODE SYSTEMTo further protect your car from theft, it has been
fitted with an engine immobilising system. It is
automatically activated when the ignition key
is removed.
Each key contains an electronic device which
modulates the signal emitted during ignition by an
antenna built into the ignition device. The signal
is the "password", different every time the car
is started, through which the control unit
recognises the key and enables starting.
OPERATION
Each time the car is started by turning the ignition
key to MAR, the Lancia CODE system control
unit sends an acknowledgement code to the engine
control unit to deactivate the immobilizer. The
code is sent only if the control unit of the Lancia
CODE system has acknowledged the code received
from the key.
Each time the ignition key is turned to STOP, the
Lancia CODE system deactivates the functions
of the engine management control unit. If, during
starting, the code is not correctly recognised, the
warning light switches on in the instrument
panel. In this case, turn the key to STOP and then
to MAR; if it is still locked, try again with the
other keys that come with the vehicle. Contact a
Lancia Dealership if you still cannot start the
engine.Warning light
switching on while driving
If the
warning light switches on, this means
that the system is running a self-diagnosis (for
example for a voltage drop). If the problem
persists, contact a Lancia Dealership.
23GETTING TO
KNOW YOUR CARSAFETY
STARTING
AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

MAIN BEAM HEADLIGHTS
To switch on the main beam headlights, with ring
nut in position
, push the stalk forward toward
the dashboard (unstable position). The
warning light will come on in the instrument
panel.
When the stalk is released, the lights deactivate,
the main beam headlights reactivate and thewarning light switches off.
It is not possible to switch on the main beam
headlights in fixed mode if the automatic lighting
control system is active.
FLASHING
You can flash the headlights by pulling the stalk
towards the wheel (unstable position). Thewarning light will come on in the instrument
panel.
DIRECTION INDICATORS
Bring the stalk to the (stable) position:
upwards:right-hand direction indicator
activation;
downwards:left-hand direction indicator
activation.
Warning light
or
should flash in the
instrument panel. The indicators switch off
automatically when the steering wheel is
straightened.Lane change function
If you wish to signal a lane change, put the left
stalk in the unstable position for less than half a
second. The direction indicator on the selected
side flashes three times and then switches off
automatically.
“FOLLOW ME HOME” DEVICE
This allows the space in front of the car to be lit
up for a certain period of time.
Activation:with the ignition key on STOP or
removed, pull the stalk towards the steering wheel
within 2 minutes from when the engine is turned
off.
At each single movement of the stalk, the lights
will remain on for an extra 30 seconds up to a
maximum of 210 seconds; then the lights are
switched off automatically.
Each time the stalk is operated, the
warning
light on the instrument panel switches on and the
display also shows a message and how long the
function will remain active.
The
warning light switches on when the stalk
is first moved and stays on until the function is
automatically deactivated. Each time the stalk is
activated it increases the time that the lights
remain on.
Deactivation:keep the stalk pulled towards the
steering wheel for more than two seconds.
49GETTING TO
KNOW YOUR CARSAFETY
STARTING
AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

Activation
Move the right lever down by one click. The
activation of the sensor is signalled by a "stroke"
to show that the command has been acquired.
IMPORTANT Keep the glass in the sensor area
clean.
By turning ring nut B fig. 35 is it possible to
increase the sensitivity of the rain sensor to obtain
a more rapid variation between wiper still (no
stroke) when the windscreen is dry, to wiper
at first continuous speed (slow continuous
operation).
The increasing of the rain sensor sensitivity is also
signalled by a stroke of the wipers.
If the windscreen washer is used with the rain
sensor activated, the normal washing cycle is
performed, after which the rain sensor resumes its
normal automatic operation.Deactivation
Turn the ignition key to STOP. The next time the
vehicle is started (key turned to MAR), the sensor
is not reactivated. To activate the sensor, move
the stalk upwards or downwards and then to
central position. Rain sensor activation will be
indicated by at least one wiper “stroke” even if the
windscreen is dry.
The rain sensor is able to recognise, and
automatically adjust itself in the presence of the
following conditions:
❒presence of dirt on the controlled surface (salt,
dirt, etc.);
❒presence of streaks of water caused by the worn
window wiper blades;
❒difference between day and night.
Do not activate the rain sensor when
washing the car in an automatic car
wash.Make sure the device is switched off if
there is ice on the windscreen.
WARNING
Make sure the device is switched off
whenever the windscreen
must be
cleaned.
fig. 36
L0F0188
52GETTING TO
KNOW YOUR CAR
SAFETY
STARTING
AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

EOBD SYSTEMThe EOBD system (European On Board
Diagnosis) carries out a continuous diagnosis of
the components of the car related to emissions. It
also alerts the driver about component
deterioration by switching on the warning light on
the instrument panel and the displaying of a
relevant message (for versions/markets, where
provided) (see the chapter “Warning lights and
messages”).
The aim of the EOBD system (European On Board
Diagnosis) is to:
❒monitor the system efficiency;
❒indicate an increase in emissions;
❒indicate the need to replace damaged
components.
The system also has a diagnosis connector that
can be interfaced to suitable instruments, to read
the error codes stored in the control unit together
with a series of specific parameters for engine
operation and diagnosis.
IMPORTANT After eliminating the failure, to
check the system completely, Lancia Dealerships
run a bench test and, if necessary, road tests which
may also call for a long journey.
DUALDRIVE ELECTRIC POWER
STEERINGThis only operates with the key turned to MAR
and the engine started. The steering allows the
force required at the steering wheel to be adjusted
to suit driving conditions.
IMPORTANT When turning the ignition key
quickly, full power steering functionality can be
achieved after a few seconds.
CITY FUNCTION ACTIVATION/
DEACTIVATION
Press button CITY fig. 73 to activate/deactivate
the function. The activation of the function is
signalled by the word CITY on the display (in
some versions it is signalled by the word CITY
appearing on the instrument panel).
fig. 73
L0F0082
88GETTING TO
KNOW YOUR CAR
SAFETY
STARTING
AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

Front seats (warning light no. 1 = driver and
no. 4 = passenger)
Driver
If the driver is the only occupant and the seat belt
is not fastened, when 20 km/h is exceeded or
when travelling at a speed from 10 to 20 km/h for
longer than 5 seconds, an acoustic signal sequence
will be started (front seats) consisting of a tone
for 6 seconds followed by a 90 second beep. The
warning light will flash. The warning lights will
stay on fixed at the end of the cycle until the
engine is stopped. The acoustic signal will
be interrupted immediately when the driver's seat
belt is fastened and the warning light will turn
green.
The reminder cycle (acoustic and visual) will be
repeated as described above and the red warning
light will flash if the seat belt is unfastened again
while travelling.
Passenger
A similar situation applies to the front passenger,
with the difference that the warning light turns
green and the indication is also interrupted when
the passenger leaves the car.
It both front seat belts are unfastened while the
car is travelling a few seconds apart, the acoustic
indication will refer to the most recent event
and the two warning lights will proceed with the
visual indication independently.Rear seats (warning light no. 2 and no. 3)
For rear seats, the reminder cycle occurs only
when any seat belt is unfastened (red flashing
warning light). In this condition, the warning light
referred to the seat belt which has been
unfastened will become red and blink for
approximately 30 seconds. An acoustic signal is
also issued.
The visual indication (red flashing) will start and
stop independently for each warning light if
several seat belts are unfastened. The warning
light will become green when the relevant seat belt
is fastened again.
The rear seat warning lights will switch off,
regardless of the state of the belt (red or green)
approximately 30 seconds after the last signal.
IMPORTANT When the ignition key is turned to
MAR, if all the front and rear belts are already
fastened the warning lights will remain lit with a
constant green light for about 30 seconds.
112
GETTING TO KNOW
YOUR CAR
SAFETY
STARTING AND
DRIVING
W
ARNING LIGHTS
ANDMESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

IMPORTANT When the ignition key is turned to
MAR, the "belts fastened" warning lights will
be lit with a constant green light while those for
the belts unfastened will be lit with a constant red
light. If the last belt is also fastened, the the
warning lights will remain lit with a steady green
light for about 30 seconds then they will switch
off.
PRETENSIONERSThe car is equipped with front seat belt
pretensioners, which draw back the seat belts by
several centimetres in the event of a strong frontal
impact. This guarantees the perfect adherence of
the seat belts to the occupants bodies before
the retention action begins. It is evident that the
pretensioners have operated when the belt
withdraws toward the reel. This car is also
equipped with a second pretensioner (in the kick
plate area). Its activation is signalled by the
shortening of the metal cable. A slight discharge of
smoke may be produced during the activation of
the pretensioner which is not in harmful and does
not involve any fire hazard.
IMPORTANT To obtain the highest degree of
protection from the action of the pretensioning
device, wear the seat belt tight to the chest and
pelvis.
The pretensioner does not require any
maintenance or lubrication: any changes to its
original conditions will invalidate its efficiency. If,
due to unusual natural events (floods, sea storms,
etc.), the device has been affected by water and
mud, it must be replaced.
113GETTING TO KNOW
YOUR CARSAFETYSTARTING AND
DRIVING
W
ARNING LIGHTS
ANDMESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

AIRBAG FAILURE (red)
Turning the key to the MAR-ON position
illuminates the warning light, but it should switch
off after a few seconds. The warning light switches
on constantly (on some versions, with a message
on the display and a symbol on the display) to
indicate an airbag system fault.
WARNING
If when turning the key to MAR the
warning light
does not turn on
or stays on whilst driving, a failure may have
occurred in the restraint systems. In this
case the air bags or pretensioners may not
be deployed in an impact or, in a lower
number of cases, they may be deployed
accidentally. Before continuing, contact a
Lancia Dealership immediately to have the
system checked.
WARNING
A fault with the
warning light is
indicated by flashing of the
warning light, which signals the
deactivation of the passenger side front air
bag. In addition, the airbag system
automatically disables the air bags on the
passenger's side (both front and side airbags
for versions/markets, where provided). In
this case, the warning light
may not
indicate a fault in the restraint systems.
Before continuing, contact a Lancia
Dealership immediately to have the system
checked.
PASSENGER/SIDE AIR BAGS
DEACTIVATED (amber)
The
warning light switches on when the front
passenger's airbag and side bag are disabled. With
front passenger airbag on, when the ignition key
is turned to MAR, the
warning light switches on
constantly for several seconds, it flashes for
another few seconds and then it should switch off.
144
GETTING TO KNOW
YOUR CAR
SAFETY
STARTING AND
DRIVINGWARNING LIGHTS
AND
MESSAGESIN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICA
TIONS
INDEX

WARNING
The driving speed should always be
suitable to traffic
conditions, weather
conditions and the driver should always
comply with the Highway Code. The engine
may be turned off while the DPF light is
on; however, repeated interruption of the
regeneration process may result in
premature exhaustion of engine oil. For this
reason, always wait until the warning light
switches off before stopping the engine as
described above. It is not a good idea to
complete DPF regeneration with the
car stationary.GENERIC FAILURE INDICATION
(amber)
(for versions/markets, where provided)
The warning light switches on in the following
circumstances. In these cases contact a Lancia
Dealership to have the fault fixed as soon as
possible.
Speed limit exceeded
(for versions/markets, where provided)
The warning light switches on (together with a
message on the display) when the speed limit set
in the Setup Menu is exceeded.When the car exceeds this value, on some versions
a message and a symbol are shown in the display
and an acoustic signal is emitted.
Fuel cut-off system intervention/fault
The warning light switches on (together with a
message on the display) in the event of fuel cut-off
system intervention/fault.
Start&Stop failure
(for versions/markets, where provided)
The warning light switches on (together with a
message on the display) when a Start&Stop
system failure is detected.
Rain sensor failure
(for versions/markets, where provided)
The warning light switches on (together with a
message on the display) when a rain sensor failure
is detected.
Parking sensor failure
(for versions/markets, where provided)
The warning light switches on (together with a
message on the display) when a parking sensor
failure is detected.
151GETTING TO KNOW
YOUR CAR
SAFETY
STARTING AND
DRIVINGWARNING LIGHTS
AND
MESSAGESIN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICA
TIONS
INDEX