ECU LAND ROVER DEFENDER 1996 Workshop Manual

57STEERING
4
REPAIR POWER STEERING BOX
Service repair no - 57.10.01
NOTE: A chassis undertray may be fitted
on some vehicle derivatives to conform to
legal requirements. When under chassis
remove and refit procedures are required, it may
be necessary to remove the undertray
See
CHASSIS AND BODY, Repair, Front undertray
.
General precautions
·Whenever any part of system, is removed or
disconnected, utmost cleanliness must be
observed.
·Disconnected ports and hoses must be
plugged to prevent ingress of dirt. If metal
sediment is found in system, establish cause,
rectify and flush system.
·Do not start engine until reservoir is full as
pump will be damaged.
·Metric pipe fittings are used with 'O' ring pipe
ends on fittings to steering box.
·Follow normal 'O' ring replacement procedure
whenever pipes are disconnected.
·Ensure compatible metric components when
fitting replacement pipes.
CAUTION: After refitting steering linkage
parts follow correct procedure to ensure
that road wheels, steering box and
steering wheel are correctly positioned relative to
each other when in straight ahead condition.
NOTE: When drag link is disconnected
from steering box, travel available at
steering wheel to each full lock is not
equal.
Remove
1.Site vehicle on level surface.
2.Apply park brake, chock rear wheels, raise
vehicle and locate axle stands. Alternatively,
raise vehicle on a hoist.
3.Remove road wheel.
4.Remove panhard rod
See FRONT
SUSPENSION, Repair, Panhard rod
.
5.Disconnect steering damper from drag link.
6.Disconnect drag link from drop arm, see J6305
on opposite page, using a suitable extractor.
7.Slacken, but do not remove nut securing tie bar
to mounting arm.8.Remove 2 bolts securing tie bar to steering box
and move aside.
9.Remove filler cap from power steering fluid
reservoir.
10.Position suitable container under steering box.
11.Disconnect feed and return pipes from steering
box and drain fluid.
12.Plug open pipes and steering box ports to
prevent ingress of dirt. Refit fluid reservoir filler
cap.
13.Centralise steering
See Centralise steering
box
.
14.Remove pinch bolt securing lower shaft
universal joint to power steering box.
15.Remove 4 bolts and 2 tab washers securing
steering box to chassis side member.
16.Withdraw steering box.
17.Clean all mounting faces, unions etc. prior to
refitting.
Refit
18.Position steering box to chassis side member,
ensuring locating peg is engaged. Fit tab
washers and tighten bolts to
81 Nm (60 lbf/ft).
19.Fit pinch bolt and nut securing universal joint to
power steering box spline. Tighten to
25 Nm (18
lbf/ft).
20.Secure tie bar to mounting arm and steering box.
Tighten fixings to
81 Nm (60 lbf/ft),starting with
tie bar to mounting nut, then loosen fixings by
one complete turn.
21.Check steering box and adjust if necessary
See
Adjustment, Power steering box - adjust
.
22.Refit drag link to drop arm and tighten nut to
40
Nm (30 lbf/ft).
Fit new split pin to retaining nut.

STEERING
7
REPAIR POWER STEERING PUMP
Service repair no - 57.20.14
Remove
NOTE: A chassis undertray may be fitted
on some vehicle derivatives to conform to
legal requirements. When under chassis
remove and refit procedures are required, it may
be necessary to remove the undertray
See
CHASSIS AND BODY, Repair, Front undertray
.
1.Disconnect battery.
2.Remove viscous fan unit
See COOLING
SYSTEM, Repair, Viscous coupling and fan
.
3.Restrain steering pump pulley, slacken but do
not remove 3 bolts securing pulley.
4.Remove drive belt
See ELECTRICAL, Repair,
Auxiliary drive belt
.
5.Remove bolts and remove pulley.
6.Position suitable container beneath steering
pump.
7.Slacken retaining clip and disconnect return
hose from steering pump.
8.Disconnect high pressure pipe from steering
pump.
9.Allow steering fluid to drain into container.
CAUTION: Plug all connections to prevent
ingress of dirt.
10.Remove 4 bolts securing steering pump bracket
to engine auxiliary mounting bracket.
11.Remove pump and bracket assembly.
12.Remove 3 bolts and detach mounting bracket
from pump.
Refit
13.Fit mounting bracket to replacement steering
pump. Tighten bolts to
9 Nm (7 lbf/ft).
14.Fit pump and bracket to auxiliary mounting
bracket. Tighten bolts to
35 Nm (26 lbf/ft).
15.Connect high pressure feed pipe to steering
pump and tighten to
20 Nm (15 lbf/ft).
16.Connect return hose to steering pump. Tighten
retaining clip to
3 Nm (2 lbf/ft).
17.Position pulley to steering pump, coat threads of
bolts with Loctite 242; fit but do not fully tighten
bolts.
18.Fit drive belt
See ELECTRICAL, Repair,
Auxiliary drive belt
.
19.Restrain steering pump pulley, tighten bolts to
10
Nm (7lbf/ft).
20.Fit viscous fan unitSee COOLING SYSTEM,
Repair, Viscous coupling and fan
.
21.Bleed power steering system
See Power
steering system - bleed
.
POWER STEERING PUMP DRIVE BELT
Service repair no - 57.20.02
NOTE: For details of drive belt remove and
refit
See ELECTRICAL, Repair, Auxiliary
drive belt
.

57STEERING
8
REPAIRREV: 05/99 LOWER STEERING SHAFT AND UNIVERSAL
JOINTS
Service repair no - 57.40.16
Remove
1.Remove vehicle bonnet.
2.Set road wheels and steering wheel in straight
ahead position.
3.Mark relationship of steering column inner shaft
to top universal joint.
4.Remove 2 bolts from top universal joint.
5.Remove lower bolt from bottom universal joint.
6.Slacken upper bolt of lower universal joint and
withdraw shaft.
7.Inspect upper and lower universal joints for wear
and excessive play, renew if necessary.
8.Inspect universal joints for stiffness, lubricate if
necessary.Refit
9.Fit universal joints so pinch bolt holes line up
with flat on shaft. Note that the long joint is fitted
to short length of shaft and short joint to long
end.
10.With steering lock engaged and road wheels in
straight ahead position, line up assembly marks.
11.Position shaft assembly onto steering column.
Move assembly up spline to enable lower
universal joint to fit onto steering box splines.
12.Align bolt holes with grooves in splines. Fit pinch
bolts and tighten to
25 Nm (18 lbf/ft).
STEERING WHEEL
Service repair no - 57.60.01
Remove
1.Set road wheels and steering wheel in straight
ahead position.
2.Prise decal from steering wheel pad.
3.Remove retaining nut and shakeproof washer.
Make alignment marks on column and wheel
pad.
4.Withdraw steering wheel from column spline.
Refit
5.Turn indicator cancelling ring so that slots are
vertical and lug with arrow points to the left, in
direction of indicator switch.
6.Ensure front road wheels are in straight ahead
position.
7.Fit steering wheel with finisher attachment lug at
the bottom, ensuring indicator cancelling forks
locate in cancelling ring slots. Align assembly
marks.
8.Secure wheel with retaining nut and new
shakeproof washer. Tighten to
43 Nm (32 lbf/ft).

STEERING
9
REPAIR REV: 05/99 STEERING COLUMN LOCK
Service repair no - 57.40.28
Remove
1.Disconnect battery.
2.Set road wheels in straight ahead position.
3.Remove steering wheel
See Steering wheel.
4.Remove instrument panel
See INSTRUMENTS,
Repair, Instrument panel
.
5.Remove steering column nacelle
See Steering
column nacelle
.
6.Note position of harness leads on back of starter
switch and disconnect lucars. If fitted, remove
alarm system passive coil from switch
See
ELECTRICAL, Repair, Vehicle immobilisation
and alarm system
.
7.Using a punch or stud extractor remove 2 shear
bolts securing steering lock/starter switch to
column.
8.Remove steering lock and collect 2 washers
between lock and clamp.
Refit
9.Fit steering lock/switch in position and line up
with switch plunger.
10.Secure lock to column with clamp and new shear
bolts. Evenly tighten bolts but do not shear them.
11.Temporarily fit steering wheel and operate lock
and switch mechanism to ensure it functions
correctly.
12.Fully tighten retaining bolts until heads shear.
13.Connect harness leads to rear of starter switch.
If applicable, fit alarm system passive coil
See
ELECTRICAL, Repair, Vehicle immobilisation
and alarm system
.14.Fit steering column nacelle
See Steering
column nacelle
.
15.Fit instrument panel
See INSTRUMENTS,
Repair, Instrument panel
.
16.Fit steering wheel
See Steering wheel.
17.Reconnect battery.

57STEERING
12
REPAIR STEERING DAMPER
Service repair no - 57.55.21
Remove
1.Park vehicle on level ground and chock rear
wheels.
2.Raise vehicle and locate axle stands or use a
ramp.
3.Remove bolt securing steering damper to drag
link bracket.
4.Remove retaining nuts, washers and rubber
bush securing damper to chassis mounting.
5.Withdraw damper.
6.Check rubber bushes and washers, renew if
necessary.Refit
7.Ensuring rubber bushes and washers are
correctly positioned, fit steering damper to
chassis mounting.
8.Fit damper to drag link bracket.
9.Remove axle stands or vehicle from ramp.

STEERING
13
REPAIR REV: 05/99 TRACK ROD AND LINKAGE
Service repair no - 57.55.09
Remove
1.Park vehicle on level ground and chock rear
wheels.
2.Raise vehicle and locate axle stands or use a
ramp.
3.Centralise steering
See Adjustment,
Centralise steering box
.
4.Unscrew 2 bolts and remove track rod protection
bracket from axle differential housing.
5.Remove split pin and castellated nut securing
track rod to swivel housing arms.
6.Disconnect track rod ball joints using
LRT-57-018.
7.Remove track rod.
8.Slacken clamp bolts.
9.Unscrew ball joints.

STEERING
15
REPAIR REV: 05/99 DRAG LINK AND DRAG LINK ENDS
Service repair no - 57.55.17
Remove
1.Park vehicle on level ground and chock rear
wheels.
2.Set road wheels in straight ahead position.
3.Raise vehicle and fit axle stands or use a ramp.4.Remove front road wheel.
5.Disconnect steering damper at drag link bracket.
6.Remove split pin and castellated nut securing
drag link ball joint to swivel housing arm.
7.Disconnect drag link ball joints using
LRT-57-018.
8.Remove drag link.
9.Slacken clamp bolts.
10.Unscrew ball joints and remove from drag link.
11.Clean internal threads of drag link.
12.Fit new ends to drag link and loosely fit clamp
bolts.
13.Set ball joints to drag link measurement to 28,5
mm.
14.Adjust ball pin centres to nominal length of 924
mm, this length is adjusted during refit.

STEERING
1
OVERHAUL POWER STEERING BOX - ADWEST
Service repair no - 57.10.07
Overhaul
NOTE: Overhaul of steering box should
not be carried out during the warranty
period.
WARNING: Wear safety glasses while
removing and refitting circlips and
retaining ring.
CAUTION: Absolute cleanliness is
essential when overhauling power steering
box.
1.Remove steering box from vehicleSee Repair,
Power Steering Box
. Mark drop arm and
steering box for realignment on assembly.
Remove drop arm using extractorLRT-57-012.
Loosen drop arm securing nut, but do not
remove before using extractor. Remove dirt
excluder from output shaft.
2.Drain oil, remove blanking plugs and bleed
screw. Hold steering box over suitable container,
turn input shaft from lock to lock, until oil is
drained. Refit bleed screw.
3.Rotate retainer ring until one end is 12 mm from
extractor hole. Using a drift through hole in
cylinder, lift retaining ring from groove in cylinder
bore.
4.Remove retainer ring, using a screwdriver.
5.Turn input shaft (left lock on left hand drive, right
lock on right hand drive) until piston pushes out
cover. Turn input shaft fully in opposite direction,
applying pressure to piston.
6.Remove set screw retaining rack pad adjuster.
7.Remove rack adjuster and pad.
8.Remove sector shaft adjuster locknut.
9.Remove four bolts from sector shaft cover.
10.Screw in sector shaft adjuster until cover is
removed.
NOTE: Sealant is applied to hexagon
socket to 'tamperproof' sector shaft
adjuster.
11.Slide out sector shaft.

STEERING
9
OVERHAUL Input shaft oil seal
92.Fit seal, lip side first, into housing. Use seal
saverLRT-57-016and seal installer
LRT-57-026. Note that seal is fitted to a depth of
4.75 - 5.00 mm from face of box.
93.Secure seal with circlip.
94.Smear inner lip of dirt excluder with PTFE
grease. Fit dirt excluder usingLRT-57-027.
When fitted correctly outer shoulder of excluder
is 4.00 - 4.50 mm from face of box, dimension X.
95.Remove drop arm. Smear inner lip of dirt
excluder with PTFE grease and refit, ensuring
outer lip is flush with casing.
96.With input shaft on centre, align assembly marks
on drop arm and steering box. Fit drop arm to
steering box using a new tab washer. Tighten to
176 Nm (130 lbf/ft),bend over tab.
97.Fit steering box
See Repair, Power Steering
Box
.

FRONT SUSPENSION
1
DESCRIPTION AND OPERATION DESCRIPTION
The front suspension design allows maximum wheel
travel and axle articulation providing good ground
clearance without loss of traction or directional
stability.
Long radius arms are fitted to the front axle and
provide maximum axle articulation which is vital for off
road performance. The radius arms are secured to
fabricated mounting brackets welded to the front axle.
Flexible rubber bushes are used on a stem end joint
to secure the rear of the radius arms to mountings on
the chassis cross member.
A panhard rod, which ensures that the front axle
remains centrally located, is fitted transversely and
also uses ferrule rubber bush mountings at both axle
and chassis locations.Two rubber bearing bushes, with retaining straps,
secure the rear of the anti-roll bar to the chassis
mountings, while bushed links support the front of the
bar to the front axle.
Conventional long travel coil springs and hydraulic
shock absorbers are used to control body movement
in all conditions. The shock absorbers are secured to
fabricated towers which are bolted to the chassis. The
upper and lower fixings use a single location stud with
flexible rubber bushes, support washers and securing
nuts. Retaining plates are used to secure the coil
springs to the fabricated towers and axle mountings.
Rubber bump stops are fitted underneath the chassis,
adjacent to the front road springs, and prevent
possible damage that could occur should there be
excessive axle to chassis movement.
Front suspension
1.Panhard rod
2.Radius arms
3.Coil springs
4.Shock absorber
5.Anti-roll bar