catalytic converter LAND ROVER DEFENDER 1996 Workshop Manual

01INTRODUCTION
10
INFORMATION CROSS REFERENCE OF EMISSION SYSTEM
TERMINOLOGY
NEW TERM (ACRONYM)
Accelerator pedal (AP).................................................
Air cleaner (ACL)..........................................................
Air conditioning (AC)....................................................
Battery positive voltage (B+)........................................
Closed loop (CL)..........................................................
Closed throttle position (CTP)......................................
Canister purge valve (CANPV)....................................
Data link connector (DLC)...........................................
Diagnostic trouble code (DTC).....................................
Distributor ignition (DI).................................................
Engine control module (ECM)......................................
Engine coolant level (ECL)...........................................
Engine coolant temperature (ECT)..............................
Engine coolant temperature sensor (ECTS)................
Engine speed (RPM)....................................................
Evaporative emission system (EVAP)..........................
Engine fuel temperature sensor (EFTS)......................
4th gear, 3rd gear etc. (4GR, 3GR)..............................
Fuel pump (FP)............................................................
Fan control module (FCM)...........................................
Generator (GEN)..........................................................
Ground (GND)..............................................................
Heated oxygen sensor (H02S)....................................
Idle air control (IAC)......................................................
Idle air control valve (IACV).........................................
Ignition control module (ICM).......................................
Intake air temperature (IAT).........................................
Manifold vacuum zone (MVZ)......................................
Mass air flow sensor (MAFS).......................................
Open loop (OL)............................................................
Relay module (RM)......................................................
Solid state relay module (SSRM).................................
Three way catalytic converter (TWC)..........................
Throttle body (TB)........................................................
Throttle position sensor (TPS)......................................
Transmission range (TR)..............................................
Wide open throttle (WOT)............................................OLD TERM (ACRONYM)
Throttle pedal (-)..........................................................
Air cleaner (-)...............................................................
Air conditioning (AC)....................................................
Battery plus, bat +, bat feed (B+).................................
Closed loop (-).............................................................
Closed throttle, idle position (-)....................................
Charcoal canister purge valve (-).................................
Serial link (-)................................................................
Fault code (-)...............................................................
Electronic ignition (-)....................................................
Electronic control unit (ECU)........................................
Coolant level (-)...........................................................
Coolant temperature (temp).........................................
Coolant temperature thermistor (-)..............................
Engine speed (rev/min)................................................
Evaporative loss system (ELC)...................................
Fuel temperature thermistor (-)....................................
Fourth gear, 3rd gear (-)..............................................
Fuel pump (-)...............................................................
Condenser fan timer (-)................................................
Alternator (-)................................................................
Ground, earth (B-)........................................................
Lambda (02) sensor (-)................................................
Idle speed control (ISC)................................................
Stepper motor (-).........................................................
Ignition module (-)........................................................
Intake temperature/ambient temperature (-)................
Manifold depression, vacuum (-).................................
Air flow meter (-)..........................................................
Fault code display unit (-)............................................
Open loop (-)...............................................................
Relay (-).......................................................................
Control unit (-)..............................................................
Catalyst, catalytic converter (CAT)..............................
Throttle housing (-)......................................................
Transmission gear (-)...................................................
Full throttle, wide open throttle (WOT).........................

10MAINTENANCE
12
MAINTENANCEREV: 05/99 LUBRICATE PROPELLER SHAFT UNIVERSAL
AND SLIDING JOINTS
1.Clean all grease nipples on front and rear
propeller shafts.
2.Using a low pressure hand grease gun, apply
recommended grease
See LUBRICANTS,
FLUIDS AND CAPACITIES, Information,
Recommended lubricants and fluids
to grease
nipples at front and rear propeller shaft universal
and sliding joints.
VISUALLY CHECK BRAKE, FUEL, CLUTCH
HOSES/PIPES/UNIONS FOR CHAFING, LEAKS
AND CORROSION
CHECK EXHAUST SYSTEM FOR LEAKS,
SECURITY AND DAMAGE
RENEW CATALYTIC CONVERTERS
See
MANIFOLD AND EXHAUST SYSTEM, Repair,
manifolds and exhaust system
CHECK FOR FLUID LEAKS FROM POWER
STEERING AND SUSPENSION SYSTEMS,
HYDRAULIC PIPES AND UNIONS FOR CHAFING
AND CORROSION
CHECK/TIGHTEN STEERING UNIT AND STEERING
ROD BALL JOINT FIXINGS, CHECK CONDITION
OF BALL JOINTS AND DUST COVERSBall joints are lubricated for life during manufacture
and require no further lubrication unless the rubber
boot has been dislodged or damaged. All joints should
be checked at specified service intervals, but more
frequently if vehicle is used under arduous conditions.
1.Check for wear in joints by moving ball joint up
and down vigorously. If free movement is
apparent, fit a new joint assembly.
See
STEERING, Repair, Drop arm ball See
STEERING, Repair, Track rod and See
STEERING, Repair, Drag link and drag link
ends
CHECK/TIGHTEN FRONT AND REAR AXLE
SUSPENSION LINK FIXINGS, CHECK CONDITION
OF MOUNTING RUBBERS
DRAIN AND CLEAN FUEL SEDIMENTER, IF
FITTED
The fuel sedimenter is located on a chassis side
member on the RH side of vehicle near rear wheel. It
increases the working life of the fuel filter by removing
larger droplets of water and other matter from fuel.
NOTE: On 110/130 models with a twin tank
fuel system, two sedimenters may be
fitted, one on each side of the vehicle
chassis.
1.Slacken drain plug and allow any water to drain
off.

MANIFOLD AND EXHAUST SYSTEM
1
DESCRIPTION AND OPERATION MANIFOLDS AND EXHAUST SYSTEM
Description
The exhaust systems fitted on all models with the
300Tdi engine comprise three sections; front pipe
assembly, intermediate silencer assembly, and tail
pipe and silencer assembly. All sections, including
silencers, are manufactured from luminised steel to
give the system a durable working life under all
conditions. Special clamps are provided to ensureleak proof jointing between the various sections,
which are supported by flexible rubber mountings.
Catalytic convertor
When fitted, the catalytic converter is integral with the
front pipe assembly, which also incorporates a flexible
joint. The catalyst forms part of the engine emission
control that can also include an EGR valve system
See FUEL SYSTEM, Repair, EGR valve
Exhaust system - 90
1.Gasket
2.Front pipe
3.Front pipe with catalytic converter
4.Front mounting bracket
5.Intermediate silencer6.Intermediate mounting brackets
7.Tail pipe silencer*
8.Tail pipe silencer mounting
9.Tail pipe mounting
* Deleted on later models

30MANIFOLD AND EXHAUST SYSTEM
2
DESCRIPTION AND OPERATION The catalyst comprises platinum coated ceramic
elements. The Hydrocarbons (HC), Oxides of nitrogen
(NOx) and Carbon monoxide (CO) emitted by the
engine react with the catalytic element and exhaust
temperature to convert the toxic gas into Nitrogen
(N
2), Carbon dioxide (CO2) and water vapour.
Exhaust system - 110/130
1.Gasket
2.Front pipe
3.Front pipe with catalytic converter
4.Front mounting bracket
5.Intermediate silencer6.Intermediate mounting brackets
7.Tail pipe silencer
8.Tail pipe silencer mounting
9.Tail pipe mounting