power steering LAND ROVER DEFENDER 1996 User Guide

10MAINTENANCE
12
MAINTENANCEREV: 05/99 LUBRICATE PROPELLER SHAFT UNIVERSAL
AND SLIDING JOINTS
1.Clean all grease nipples on front and rear
propeller shafts.
2.Using a low pressure hand grease gun, apply
recommended grease
See LUBRICANTS,
FLUIDS AND CAPACITIES, Information,
Recommended lubricants and fluids
to grease
nipples at front and rear propeller shaft universal
and sliding joints.
VISUALLY CHECK BRAKE, FUEL, CLUTCH
HOSES/PIPES/UNIONS FOR CHAFING, LEAKS
AND CORROSION
CHECK EXHAUST SYSTEM FOR LEAKS,
SECURITY AND DAMAGE
RENEW CATALYTIC CONVERTERS
See
MANIFOLD AND EXHAUST SYSTEM, Repair,
manifolds and exhaust system
CHECK FOR FLUID LEAKS FROM POWER
STEERING AND SUSPENSION SYSTEMS,
HYDRAULIC PIPES AND UNIONS FOR CHAFING
AND CORROSION
CHECK/TIGHTEN STEERING UNIT AND STEERING
ROD BALL JOINT FIXINGS, CHECK CONDITION
OF BALL JOINTS AND DUST COVERSBall joints are lubricated for life during manufacture
and require no further lubrication unless the rubber
boot has been dislodged or damaged. All joints should
be checked at specified service intervals, but more
frequently if vehicle is used under arduous conditions.
1.Check for wear in joints by moving ball joint up
and down vigorously. If free movement is
apparent, fit a new joint assembly.
See
STEERING, Repair, Drop arm ball See
STEERING, Repair, Track rod and See
STEERING, Repair, Drag link and drag link
ends
CHECK/TIGHTEN FRONT AND REAR AXLE
SUSPENSION LINK FIXINGS, CHECK CONDITION
OF MOUNTING RUBBERS
DRAIN AND CLEAN FUEL SEDIMENTER, IF
FITTED
The fuel sedimenter is located on a chassis side
member on the RH side of vehicle near rear wheel. It
increases the working life of the fuel filter by removing
larger droplets of water and other matter from fuel.
NOTE: On 110/130 models with a twin tank
fuel system, two sedimenters may be
fitted, one on each side of the vehicle
chassis.
1.Slacken drain plug and allow any water to drain
off.

12ENGINE
4
REPAIR
14.Disconnect engine harness multi-plug.
15.Remove single bolt securing transmission
breather pipe clip to cylinder head and move
breather pipes aside.
16.Disconnect multi-plug and vacuum pipe from
EGR valve, if fitted.
17.Remove starter motor cover and disconnect
battery and fuse box leads.
18.Remove 3 retaining nuts and disconnect exhaust
down pipe.
19.Disconnect inlet and outlet hoses from power
steering pump.
20.Disconnect bleed hose from thermostat housing.
21.Release bleed hose from retaining clips on front
timing cover plate.
22.Remove split pin securing inner throttle cable to
injector pump lever.
23.Depress tags on outer cable adjusting nut,
remove cable from mounting bracket and move
aside.
24.If fitted, release hand throttle cable from
mounting bracket and injector pump lever and
move aside.
25.Disconnect feed pipe and spill return pipe from
injector pump.

12ENGINE
6
REPAIR 42.Raise engine, and locate front engine mountings
to chassis.
43.Remove gearbox support and lower engine.
44.Tighten front engine mounting to chassis fixings
to
45 Nm (33 lbf/ft).
45.Release chains from engine lifting brackets and
remove hoist.
46.Connect oil cooler pipes to oil filter adaptor.
47.Fit vacuum hose to brake servo adaptor.
48.Secure fuel feed pipe in retaining clip on air
cleaner bracket.
49.Fit fuel lift pump pipes.
50.Connect feed and spill return pipes to injector
pump.
51.If fitted, reconnect hand throttle cable to
mounting bracket and injector pump.
52.Fit outer cable adjusting nut into injector pump
mounting bracket.
53.Fit inner throttle cable to injector pump and
secure with clevis and split pin.
54.Secure bleed hose in retaining clips on front
timing cover.
55.Fit bleed hose to thermostat housing.
56.Connect inlet and outlet hoses to power steering
pump.
57.Fit down pipe to exhaust manifold and secure
with 3 nuts.
58.Connect starter motor battery and fuse box
leads.
59.If fitted, connect EGR valve multi-plug and
vacuum pipe.
60.Secure breather pipe clip to cylinder head.
61.Connect engine harness multi-plug.
62.Fit heater plug feed wire.
63.Connect electrical feed plug at rear of cylinder
head.
64.Fit heater hoses to cylinder head and heater
rails.
65.Fit feed pipe/hose to turbo-charger and
intercooler.
66.Fit rocker cover insulation.
67.Fit radiator assembly.
See COOLING SYSTEM,
Repair, Radiator
If applicable, fit air
conditioning condenser, compressor pipes and
heater matrix hoses.
See AIR CONDITIONING,
Repair, Condenser
68.Fit bonnet.
69.Reconnect battery.CRANKSHAFT PULLEY
Service repair no - 12.21.01
Remove
1.Disconnect battery.
2.Drain coolant.
See COOLING SYSTEM,
Repair, Drain and refill cooling system
3.Remove top hose from radiator.
4.Remove intercooler to induction manifold hose.
5.Remove viscous coupling and fan.
See
COOLING SYSTEM, Repair, Viscous
coupling and fan
6.Remove fan cowl.See COOLING SYSTEM,
Repair, Fan cowl
7.Remove drive belt.See ELECTRICAL, Repair,
Auxiliary drive belt
8.Fit crankshaft pulley retainerLRT-12-080and
secure with 4 bolts.
9.Remove crankshaft pulley retaining bolt
anti-clockwise using socket and suitable long
bar.
10.Remove pulley retainer.
11.Remove pulley, if necessary using extractor
LRT-12-049with thrust pad fromLRT-12-031.

COOLING SYSTEM
3
REPAIR WATER PUMP
Service repair no - 26.50.01
Remove
1.Disconnect battery.
2.Drain cooling system.
See Adjustment, Drain
and refill cooling system
3.Remove radiator top hose.
4.Remove intercooler top hose.
5.Slacken water pump and power steering pump
pulley retaining bolts.
6.Remove drive belt.
See ELECTRICAL, Repair,
Auxiliary drive belt
7.Unscrew flange nut and remove belt tensioner.
8.Remove oil filler cap and remove rocker cover
insulation.
9.Slacken retaining clip and disconnect hose at
heater rail.
10.Unscrew 3 bolts and remove water pump pulley.
11.Unscrew 3 bolts and remove power steering
pump pulley.
12.Remove 8 bolts securing water pump, noting
location of 3 through bolts into cylinder block.
13.Withdraw pump and gasket from auxiliary
mounting bracket.
14.Clean all gasket material from mating faces.
Refit
15.Using new gasket, fit water pump to mounting
bracket. Tighten bolts to
25 Nm (18 lbf/ft).
16.Fit power steering pump pulley.
17.Fit water pump pulley. Tighten bolts of both
pulleys to
25 Nm (18 lbf/ft).
18.Fit drive belt.See ELECTRICAL, Repair,
Auxiliary drive belt
19.Fit hose at heater rail.
20.Fit rocker cover insulation and oil filler cap.
21.Fit drive belt tensioner. Tighten retaining nut to
45 Nm (33 lbf/ft).
22.Fit intercooler top hose.
23.Fit radiator top hose.
24.Refill cooling system.
See Adjustment, Drain
and refill cooling system
25.Reconnect battery.

26COOLING SYSTEM
4
REPAIRREV: 05/99 AUXILIARY MOUNTING BRACKET AND GASKET
Service repair no - 26.50.04
Remove
1.Disconnect battery.
2.Drain cooling system
See Adjustment, Drain
and refill cooling system
.
3.Remove radiator top hose.
4.Remove intercooler top hose.
5.Remove viscous fan unit.
See Viscous
coupling and fan
6.Remove fan cowl.See Fan cowl
7.Slacken power steering pump pulley retaining
bolts.
8.Remove drive belt.
See ELECTRICAL, Repair,
Auxiliary Drive belt
9.Unscrew 3 bolts and remove power steering
pump pulley.
10.Remove 4 bolts securing power steering pump
mounting bracket.
11.Lower pump and bracket. Do not disconnect fluid
pipes.
12.Remove generator.
See ELECTRICAL, Repair,
Generator
13.Unscrew retaining nut and remove drive belt
tensioner.
14.Release hose clip from bracket above water
pump.15.Disconnect bottom hose/heater return hose at
water pump and heater rail.
16.Disconnect by-pass hose from water pump and
thermostat housing.
17.Remove 5 bolts (one with nut) and single
retaining nut, securing auxiliary mounting
bracket to cylinder block.
18.Withdraw mounting bracket, complete with water
pump.
19.Remove gasket and clean mating faces.
Refit
20.Using 2 slave studs, fit new gasket.
NOTE: All fixing bolts and nuts should be
tightened to
25 Nm (18 lbf/ft)unless
otherwise stated.
21.Locate mounting bracket, complete with water
pump on slave studs and secure with 4 other
fixings.
22.Remove slave studs and fit remaining bolts/nuts.
23.Fit by-pass hose to thermostat housing and
water pump.
24.Fit bottom hose/heater return hose to water
pump and heater rail.
25.Fit heater hose clip to mounting bracket.
26.Fit drive belt tensioner. Tighten nut to
45 Nm (33
lbf/ft).
27.Fit generator.See ELECTRICAL, Repair,
Generator
Do not fit drive belt at this stage.

STEERING
1
DESCRIPTION AND OPERATION DESCRIPTION
The steering system incorporates a compression joint
in the lower shaft and is designed to collapse on
impact. The mis-alignment of the upper steering
column with the steering box and the inclusion of two
universal joints, is also designed to prevent the
column moving toward the driver under frontal impact.
The steering box is located behind the first chassis
cross member and is connected to the road wheel
swivel housing by a drag link and track rod. A
hydraulic damper absorbs shocks in the steering,
caused by road wheel deflections when operating on
rough terrain.Power steering system
The power steering system comprises a hydraulic
pump which is belt driven from the engine and
supplied with fluid from a reservoir that also acts as a
cooler.
The steering box houses a self neutralizing rotary
valve which is part of the worm/valve assy and an
hydraulic piston/rack to assist the mechanical
operation. The rotary valve which is operated by
movement of the steering wheel, directs fluid pressure
to the appropriate side of the hydraulic piston/rack to
provide assistance.
Power steering system
1.Hydraulic pump
2.Fluid reservoir
3.Steering box
4.Upper column5.Universal joints
6.Lower shaft
7.Compression joint
8.Drag link

57STEERING
2
DESCRIPTION AND OPERATION
Power steering box components
1.Housing complete with sector shaft bearings
2.Cover plate complete with bearing
3.Sector shaft
4.Hydraulic piston/rack
5.Worm/valve and torsion bar assembly
6.Shims for centralizing worm/valve
7.Ball race
8.'Teflon' seals for valve sleeve
9.Bearing adjuster, locknut and seal
10.Worm shaft pressure seal, circlip and dirt
excluder11.'Teflon' and rubber seal for piston
12.End cover seal and snap ring
13.Adjustment components for piston/rack
14.Hydraulic pipe
15.Bleed screw
16.Sector shaft adjustment lock nut with seal
17.Cover plate bolts
18.Cover plate seal
19.Seal, washer and backup seal
20.Circlip and dust cover

STEERING
1
FAULT DIAGNOSIS INSUFFICIENT POWER ASSISTANCE
1.Is fluid level correct?
YES - go to 3.
NO - Fill/bleed sytem
2.Is problem a leak?
YES - Diagnose
See Power Steering Fluid
Leaks
.
NO - continue
3.Is drive belt tension correct?
YES - go to 5.
NO - Is drive belt worn or contaminated with oil?
See ELECTRICAL, Repair, Auxiliary drive
belt
.
4.Is problem resolved?
YES - end
NO - continue
5.Carry out pressure test at idle and 1000 rev/min.
See Power Steering System - Test.
6.Is correct pressure achieved?
YES - steering box defective
Not at any speed go to 9.
Not at idle go to 7.
7.Is idle speed correct?
YES-Goto8.
NO - Correct idle speed -
See ENGINE TUNING
DATA, Information, 300 Tdi Engine
.
8.Is problem resolved?
YES - end
NO - go to 9.
9.Bypass steering box using adaptor tap
LRT-57-001
10.Is correct pressure obtained?
YES - defective steering box
NO - defective steering pump
CAUTION: Do not hold steering wheel on
full lock for more than 30 seconds in any
one minute to avoid overheating fluid and
possibly damaging seals.
NOTE: 1. Excessive pressure in the
system is almost always caused by a
faulty relief valve in the PAS pump.
NOTE: 2. Insufficient pressure in the
system is usually caused by low fluid level
or PAS pump drive belt slip, or one of the
following: PAS system leaks, faulty PAS pump
relief valve, fault in steering box valve and worm
assembly, leak at piston in steering box, worn
components in PAS pump or box.

57STEERING
2
FAULT DIAGNOSIS POWER STEERING SYSTEM - TEST
NOTE: If steering lacks power assistance.
Check pressure of hydraulic pump before
fitting new components. Use fault
diagnosis chart to assist in tracing faults.
A. Steering box.
B. Steering pump.
C. Existing hose, steering box to pump.
D. HoseLRT-57-030.
E. Test adaptorLRT-57-001.
F. Pressure gaugeLRT-57-005.
G. Thread adaptorLRT-57-004.
H. Thread adaptorLRT-57-022.Procedure
1.A hydraulic pressure gauge and test adaptor is
used to test power steering system. This gauge
is able to measure 140 kgf/cm
2. The maximum
power steering system pressure is 77 kgf/cm2.
2.Under certain fault conditions of the hydraulic
pump it is possible to obtain pressures up to 105
kgf/cm
2. It is important to realise that pressure on
gauge is same pressure being exerted upon
steering wheel. When testing, turn steering
wheel gradually while reading pressure gauge.
3.Check and maintain maximum fluid level of
reservoir.
4.Examine power steering units and connections
for leaks. All leaks must be rectified before
attempting to test the system.
5.Check steering pump drive belt tension and
renew belt if necessary,
See ELECTRICAL,
Repair, Auxiliary drive Belt
.
6.Assemble test equipment and fit to vehicle, as
shown in RR3959M.
7.Open tap of adaptor.
8.Bleed system, take care not to overload
pressure gauge.
9.With system in good condition, pressures should
be:
(A) Steering wheel held on full lock and engine
running at 1,000 rev/min, 70 to 77 kgf/cm
2.
(B) Steering wheel held on full lock and engine
idling, 28 kgf/cm
2.
Checks should be carried out on both full lock
positions.
CAUTION: Do not maintain this pressure
for more than 30 seconds in any one
minute to avoid overheating fluid and
possibly damaging seals.
10.Release steering wheel and with engine idling.
Pressure should read below 7 kgf/cm
2.
11.If pressures differ to those given a fault exists.
12.To determine if fault is steering box or pump.
Close adaptor tap for a maximum five seconds.
13.If gauge does not register specified pressure,
pump is faulty.
14.Fit a new pump, bleed system and repeat test. If
low pressure or a substantial imbalance exists,
fault is in steering box valve and worm
assembly.

STEERING
3
FAULT DIAGNOSIS STEERING DAMPER
The power steering system, as well as reducing the
effort required to manoeuvre the vehicle when
parking, also helps to dampen any deflections of the
road wheels, being transmitted back to the steering
wheel.
When operating the vehicle off road, the road wheels
are often deflected by ruts and boulders causing the
steering wheel to turn left and right. This phenomenon
is known as 'steering kickback'. To subdue the effects
of 'steering kickback', a hydraulic damper is fitted in
the steering linkage between the track rod and the
differential casing. The damper, which offers the same
resistance in extension and compression, is sealed for
life.
Steering damper check
Check the condition operation of the hydraulic
steering damper as follows:
Check procedure
1.Inspect damper for casing damage or leaks.
2.Clamp one end of the damper horizontally in a
vice using soft jaws. Compress and extend the
unit by hand. Resistance should be equal in both
directions.
3.If it is felt that the unit is outside acceptable
limits, fit a new steering damperSTEERING FAULTS
Symptom:-
Excessive kickback through steering wheel - when
driven on rough terrain.
1.Is the steering damper in good working order?
See Steering Damper.
NO - Renew unit
See Repair, Steering
Damper
.
YES - Continue.
2.Is there any looseness or free play in the
steering ball joints and linkage?
YES -
See Steering Linkage Inspect.
NO - Continue.
3.Is there any looseness or worn bushes in front
suspension?
YES -
See FRONT SUSPENSION, Repair,
Radius Arm
.
NOTE: When replacing suspension bushes
ALL bushes and fixings must be replaced.
NO - Continue.
4.Is the steering exceptionally light/sensitive when
driven on good road surface?
YES - See fault symptom -Steering
excessively light/sensitive and freeplay at
steering wheel.
NO - Suspect axle swivel resistance.
5.Check the resistance of the axle swivels
See
FRONT AXLE AND FINAL DRIVE, Overhaul,
Front Stub Axle, Constant Velocity Joint and
Swivel Pin Housing
.