wheel alignment LAND ROVER DEFENDER 1996 User Guide

57STEERING
12
FAULT DIAGNOSISREV: 05/99 VISUAL CHECK AND BASIC ADJUSTMENTS
NOTE: It is important that the following
instructions are carried out in the
sequence shown and the results recorded.
1.Road springs - check that road springs are
correctly seated and are to correct specification
for vehicle. For spring specification
See
GENERAL SPECIFICATION DATA,
Information, Road Spring Data
.
2.Ride height - measure trim height from wheel
centre to wheelarch eyebrow. Record results on
data sheet.
3.Check/top up power steering fluid
See Repair,
Power Steering Fluid Reservoir
.
4.Check tension and condition of drive belt
See
ELECTRICAL, Repair, Auxiliary drive belt
.
5.Track rod/drag link - check condition of track rod,
drag link and ball joints
See Repair, Drag Link
and Drag Link Ends
.
If either component is damaged, check operation
of steering damper and steering box for
smoothness. Replace all damaged or worn
components that impair the operation of the
steering system.
6.Suspension bushes - examine all steering and
suspension bushes for signs of wear and
deterioration. Also check all fixings for torque
relaxation. Tighten to correct torque value
See
FRONT SUSPENSION, Specifications, torque,
Torque Values
.
7.Oil leaks - check front and rear axle hubs for
leak and repair as necessary.
8.Brake system - check brake system for leaks,
pipe condition, pad wear/contamination, disc
wear/condition.
9.Hub end float - check movement in the hubs by
rocking the wheels.
10.Check front wheel alignment. Vehicles displaying
a tendency to veer more than considered
allowable, it is permissible to set the front track
to parallel.11.Having completed all the above checks and
adjustments, road test vehicle
See Road Test
Procedure
.
Attempt to reproduce the symptoms established
earlier. If symptoms still exist refer to relevant
Diagnostic Chart.
STEERING LINKAGE INSPECT
NOTE: When inspecting steering linkages
and ball joints for wear the following items
must be checked.
Steering ball joints
1.Check ball joint rubber boots for security, signs
of cracking or deterioration.
2.Check ball joint assemblies for seizure i.e. no
movement on ball joint and associated
assemblies.
3.Check for excessive wear. This will be evident
as extreme movement on track rod and steering
linkages. Renew parts as necessary
See
Repair, Track Rod and Linkage
,See Repair,
Drag Link and Drag Link Ends
.
Steering linkages
1.Check all linkages for wear, deterioration and
damage. Renew parts as necessary
See
Repair, Track Rod and Linkage
,See Repair,
Drag Link and Drag Link Ends
.

STEERING
3
ADJUSTMENT FRONT WHEEL ALIGNMENT
Service repair no - 57.65.01
Checking Toe-out dimensions
NOTE: Recognised front wheel alignment
and tracking equipment should be used
for this operation. Only the use of basic
equipment is described below. No Adjustment is
provided for castor, camber or swivel pin
inclinations.
1.Set vehicle on level ground with road wheels
positioned straight ahead.
2.Push vehicle back and forwards to settle linkage.
3.Set up the equipment to manufacturers
instructions and check alignment as advised by
equipment supplier.
4.Position trammel probes on inner face of wheel,
not the rims, if the latter are damaged.
5.Measure toe-out at horizontal centre-line of
wheels.
6.Check tightness of clamp bolt fixings. Tighten to
14 Nm (10lbf/ft).
Adjust
7.Slacken clamps at both ends of track rod.
8.Rotate track rod to increase or decrease its
effective length until correct toe-out is obtained
See GENERAL SPECIFICATION DATA,
Information, Steering
.
9.Push vehicle rearwards turning steering wheel
from side to side to settle ball joints. With road
wheels set in straight ahead position, push
vehicle forward a short distance.
10.Recheck track and adjust if necessary.
11.When alignment is correct, tap ball joints in
direction of arrows to maximum of travel, to
ensure full unrestricted movement of track rod.
12.Tighten clamp bolts to
14 Nm (10 lbf/ft).
POWER STEERING PUMP DRIVE BELT
Service repair no - 57.20.01
Adjust
NOTE: For details of drive belt adjust
procedure.
See ELECTRICAL, Repair,
Auxiliary Drive Belt

57STEERING
8
REPAIRREV: 05/99 LOWER STEERING SHAFT AND UNIVERSAL
JOINTS
Service repair no - 57.40.16
Remove
1.Remove vehicle bonnet.
2.Set road wheels and steering wheel in straight
ahead position.
3.Mark relationship of steering column inner shaft
to top universal joint.
4.Remove 2 bolts from top universal joint.
5.Remove lower bolt from bottom universal joint.
6.Slacken upper bolt of lower universal joint and
withdraw shaft.
7.Inspect upper and lower universal joints for wear
and excessive play, renew if necessary.
8.Inspect universal joints for stiffness, lubricate if
necessary.Refit
9.Fit universal joints so pinch bolt holes line up
with flat on shaft. Note that the long joint is fitted
to short length of shaft and short joint to long
end.
10.With steering lock engaged and road wheels in
straight ahead position, line up assembly marks.
11.Position shaft assembly onto steering column.
Move assembly up spline to enable lower
universal joint to fit onto steering box splines.
12.Align bolt holes with grooves in splines. Fit pinch
bolts and tighten to
25 Nm (18 lbf/ft).
STEERING WHEEL
Service repair no - 57.60.01
Remove
1.Set road wheels and steering wheel in straight
ahead position.
2.Prise decal from steering wheel pad.
3.Remove retaining nut and shakeproof washer.
Make alignment marks on column and wheel
pad.
4.Withdraw steering wheel from column spline.
Refit
5.Turn indicator cancelling ring so that slots are
vertical and lug with arrow points to the left, in
direction of indicator switch.
6.Ensure front road wheels are in straight ahead
position.
7.Fit steering wheel with finisher attachment lug at
the bottom, ensuring indicator cancelling forks
locate in cancelling ring slots. Align assembly
marks.
8.Secure wheel with retaining nut and new
shakeproof washer. Tighten to
43 Nm (32 lbf/ft).

57STEERING
14
REPAIRREV: 05/99 Refit
10.Fit new ball joints to track rod and loosely tighten
clamp bolts.
11.Screw in ball joints to full extent of threads and
fully tighten clamp bolts.
CAUTION: A track rod that is damaged or
bent must be renewed. DO NOT attempt to
repair or straighten it.
12.Fit track rod to swivel housing arms and tighten
ball joint nuts to
40 Nm (30 lbf/ft).Fit new split
pin.
13.Fit track rod protection bracket to axle differential
housing.
14.Check wheel alignment
See Adjustment,
Front wheel alignment
.
15.Remove axle stands or vehicle from ramp.

74WHEELS AND TYRES
2
FAULT DIAGNOSIS FAULT - SYMPTOMS
Vibration through steering wheel
1.Check tyre pressures
See Repair, Tyre
Pressures
.
2.Check condition of tyres
See Tyre Wear Chart.
3.Check front wheel alignment
See STEERING,
Adjustment, Front Wheel Alignment
.
4.Check wheel balance
See Repair, Wheel
Balancing
.
NOTE: In the event that any apparent
vibration is not eliminated at this stage
See PROPELLER SHAFTS, Fault
diagnosis, Vibration Harshness
.
NOTE: In the event that any apparent
vibration is not eliminated at this stage, go
to steering Fault Diagnosis, Fault -
Symptom (Steering vibration, road wheel
shimmy/wobble)
See STEERING, Fault diagnosis,
Steering Faults
.
NOTE: Radial ply tyres have a flexible
sidewall, which produces a sidewall bulge
making the tyre appear under-inflated.
This is a normal condition for radial ply tyres. Do
not attempt to reduce this bulge by over-inflating
the tyre.
Key to illustration
1.Correct inflation.
2.Under-inflation.
3.Over-inflation.
4.Tread contact with road.

WHEELS AND TYRES
1
REPAIR REV: 05/99 GENERAL INFORMATION
WARNING: This is a multi-purpose vehicle
with wheels and tyres designed for both
on and off road usage. Only use wheels
and tyres specified for use on the vehicle.
The vehicle is equipped with tubeless 'S','T' or 'H'
rated radial ply tyres as standard equipment. The
tyres are of European metric size and must not be
confused with the "P" size metric tyres available in
North America.
Vehicle wheel sets, including spare wheel, must be
fitted with the same make and type of tyre to the
correct specification and tread pattern. Under no
circumstances must cross-ply or bias-belted tyres be
used.
For tyre specification and pressures
See GENERAL
SPECIFICATION DATA, Information, Wheels and
Tyres
.
Steel wheels
Tubeless tyres are mounted on 7.0 inch wide by 16
inch diameter steel wheels.
Alloy Wheels
Tubeless tyres are mounted on 7.0 inch wide by 16
inch diameter cast aluminium alloy wheels. The
surface has a paint finish covered with a clear
polyurethane lacquer. Care must be taken when
handling the wheel to avoid scratching or chipping the
finish.
The alloy wheel rim is of the asymmetric hump
type incorporating a safety hump to improve
location of the tyre bead in its seat. If difficulty is
experienced in fitting tyres to this type of rim
See
Tyre Fitting
.
WARNING: DO NOT fit an inner tube to an
alloy wheel.TYRE INSPECTION
Inspect tyres at weekly intervals to obtain maximum
tyre life and performance and to ensure compliance
with legal requirements. Check for signs of incorrect
inflation and uneven wear, which may indicate a need
for balancing or front wheel alignment,
See Fault
diagnosis, Tyre Wear Chart
, if the tyres have
abnormal or uneven wear patterns.
Check tyres at least weekly for cuts, abrasions, bulges
and for objects embedded in the tread. More frequent
inspections are recommended when the vehicle is
regularly used in off road conditions.
To assist tyre inspection, tread wear indicators are
moulded into the bottom of the tread grooves, as
shown in the illustration above.
When the tread has worn to a depth of 1.6 mm the
indicators appear at the surface as bars which
connect the tread pattern across the width of the tread
as shown in the illustration above.

CHASSIS AND BODY
3
DESCRIPTION AND OPERATION LAND ROVER 90
CHASSIS ALIGNMENT DIMENSIONS
A - Front Datum
B - Chassis Datum
C - Front axle centre line
D - Rear axle centre line
1.239,0 - 236,5 mm
2.82,0 - 79,5 mm
3.633 mm
4.2420,6 - 2418,6 mm
5.2306,4 - 2305,4 mm
6.981,2 - 978,7 mm
7.182,7 mm
8.41,5 - 37,0 mm
9.252 - 250 mm10.110 mm
11.2360mm - Wheelbase
12.636 - 634 mm
13.488 - 483 mm
14.488 - 483 mm
15.3431,1 - 3426,1 mm
16.588,3 - 586,3 mm
17.2313,8 - 2311,8 mm
18.590,5 mm
19.295,25 mm
20.519,60 - 517,00 mm
21.259,80 - 258,50 mm
22.1242,6 - 1240,6 mm
23.642,5 - 639,5 mm24.750,9 mm
25.439,5 - 436,5 mm
26.136,5 mm
27.299,5 - 295,5 mm
28.103 - 100 mm
29.131,5 - 126,5 mm
30.705,5 - 704,5 mm
31.705,5 - 704,5 mm
32.42,2 - 40,2 mm
33.491 - 486 mm
34.594,2 - 593,4 mm
35.283,0 - 282,2 mm
36.32,25 - 31,25 mm
37.397 - 395 mm

CHASSIS AND BODY
5
DESCRIPTION AND OPERATION LAND ROVER 110
CHASSIS ALIGNMENT DIMENSIONS
A - Front Datum
B - Chassis Datum
C - Front axle centre line
D - Rear axle centre line
1.4148 - 4143 mm
2.4009,5 - 4005 mm
3.978,7 - 981,2 mm
4.22 - 20 mm
5.252 - 250 mm
6.239 - 236,5 mm
7.3023,3 - 3022,3 mm
8.3030,7 - 3028,7 mm
9.155 - 153 mm
10.871,2 - 869,2 mm
11.2794 mm - Wheelbase
12.488 - 483 mm13.488 - 483 mm
14.82 - 79,5 mm
15.750,9 mm
16.750,9 mm
17.439,5 - 436,5 mm
18.439,5 - 436,5 mm
19.299,5 - 295,5 mm
20.500 - 495 mm
21.500 - 495 mm
22.594,2 - 593,4 mm
23.594,2 - 593,4 mm
24.283 - 282,2 mm
25.283 - 282,2 mm
26.1970 - 1968 mm
27.642,9 - 639,5 mm
28.750,9 mm29.290,5 mm
30.295,5 mm
31.299,5 - 295,5 mm
32.103 - 100 mm
33.1177,5 - 1175,5 mm
34.1692,5 - 1689,5 mm
35.2610 - 2606 mm
36.2040,5 - 2037,5 mm
37.1912,5 - 1909,5 mm
38.1359 - 1357 mm
39.1573 - 1571 mm
40.270 - 268 mm
41.665,5 - 663,5 mm
42.440 - 438 mm
43.32,25 - 31,25 mm

WIPERS AND WASHERS
1
OVERHAUL WIPER MOTOR
Service repair no - 84.15.18.
Dismantle
1.Remove wiper motor from vehicle
See Repair,
Wiper motor and drive rack.
2.Remove wiper motor gearbox cover.
3.Remove circlip and plain washer securing
connecting rod.
4.Withdraw connecting rod.
5.Withdraw flat washer.
6.Remove circlip and washer securing shaft and
gear.
7.Clean any burrs from gear shaft and withdraw
gear.
8.Withdraw dished washer.
9.Add alignment marks to yoke and gearbox for
reassembly.
10.Remove yoke securing bolts.11.Withdraw yoke and armature.
12.Remove brush gear assembly.
13.Remove limit switch.
Inspection and test
14.Check brushes for excessive wear, if they are
worn to 4,8 mm in length, fit a new brush gear
assembly.
15.Using a push type gauge, check that brush
spring pressure is 140 to 200 g when bottom of
brush is level with bottom of slot in brush box. Fit
a new brush gear assembly if springs are not
satisfactory.
16.Test armature for insulation and open- or
short-circuits. Use a 110 V 15 W test lamp. Fit a
new armature if faulty.
17.Examine gear wheel for damage or excessive
wear.
Key to wiper motor components
1.Flexible drive
2.Gearbox cover
3.Connecting-rod retaining washer and circlip
4.Connecting-rod
5.Flat washer
6.Gear shaft retaining washer and circlip
7.Drive gear8.Dished washer
9.Alignment marks - yoke to body
10.Yoke securing bolts
11.Armature and yoke
12.Brush gear assembly
13.Limit switch

84WIPERS AND WASHERS
2
OVERHAUL Assemble
Use Ragosine Listate Grease to lubricate gear wheel
teeth, armature shaft worm gear, connecting rod and
pin, cable rack and wheelbox gear wheels.
Use Shell Turbo 41 oil sparingly to lubricate bearing
bushes, armature shaft bearing journals, gear wheel
shaft and wheelbox spindles. Thoroughly soak felt
washer in yoke bearing with oil.
18.Fit limit switch.
19.Fit brush gear assembly.
20.Fit armature and yoke to gearbox using
alignment marks, secure with yoke retaining
bolts tightening to
23 Nm (17 lbf/ft).If a
replacement armature is being fitted slacken
thrust screw to provide end-float for fitting yoke.
21.Fit dished washer beneath gear wheel with
concave side towards gear wheel.
22.Fit gear wheel to gearbox.
23.Secure gear wheel shaft with plain washer and
circlip.
24.Fit larger flat washer over crankpin.
25.Fit connecting rod and secure with smaller plain
washer and circlip.
26.Fit gearbox cover and secure with retaining
screws.
27.Connect electrical leads between wiper motor
and limit switch.
28.To adjust armature shaft end-float, hold yoke
vertically with adjuster screw uppermost.
Carefully screw in adjuster until resistance is felt,
then back-off one quarter turn.