fuel cap LAND ROVER DEFENDER 1996 Owner's Manual

19FUEL SYSTEM
2
REPAIR
13.Remove banjo bolts securing spill return, main
fuel and boost signal pipes, refit banjo bolts after
disconnecting pipes.
14.Remove 2 bolts securing rear of pump to
mounting bracket.
15.Remove 3 pump securing nuts at flange and
withdraw pump and gasket.
16.Fit suitable caps to pipe connections to prevent
ingress of dirt.
Refit
17.Clean mating faces of pump and front cover and
fit new gasket into position over pump mounting
studs.
18.Remove pump blanking plugs.
19.Slacken the 3 bolts, securing injection pump
mounting bracket to cylinder block, sufficiently
enough to allow bracket to move.
20.Fit pump to cover and secure with 3 nuts.
Tighten to
25 Nm (18 lbf/ft).
21.Loosely attach pump to mounting bracket with
nuts and bolts, then tighten bolts securing
bracket to cylinder block and bolts securing
pump to bracket, finger tight only.
22.To ensure correct fitting and alignment of
injection pump, first tighten the 2 bolts securing
pump to mounting bracket to
25 Nm (18 lbf/ft).
Then tighten the 3 bolts securing mounting
bracket to cylinder block, also to
25 Nm (18
lbf/ft).
23.Connect spill return and main fuel pipes and
secure with banjo bolts. Tighten to
25 Nm (18
lbf/ft).
24.Connect boost signal pipe and secure with banjo
bolt. Tighten to
10 Nm (7 lbf/ft).
25.Connect fuel cut-off solenoid lead and throttle
position sensor multi-plug, if fitted.
26.Connect throttle cable and where applicable,
hand throttle cable.
27.Remove pump gear retaining toolLRT-12-045.
28.Carefully turn the pump hub nut in a clockwise
direction, sufficiently enough to enable timing
tool pin to be inserted into injection pump.
29.Fit gear retaining plate and secure with 3 bolts.
Tighten to
25 Nm (18 lbf/ft).
30.Remove timing pin.
31.Ensure flywheel timing pin is disengaged from
slot in flywheel.
32.Turn crankshaft two complete revolutions, check
timing pin fromRT-12-045can be fully and
easily inserted into the pump. At the same time
check flywheel timing pinLRT-12-044can also
be inserted in the flywheel slot.
33.If, with the flywheel timing pin located, the timing
pin cannot be inserted cleanly into the injection
pump, carry out the following:
a.Ensure flywheel timing pin is disengaged from
slot in flywheel.
b.Slacken the 3 pump gear retaining bolts.
c.Turn the pump hub nut in a clockwise
direction, sufficiently to enable timing tool pin to
be easily inserted into the injection pump.
d.Keeping the tension on the hub nut, check
that flywheel timing pin locates with slot in
flywheel.
e.Tighten the 3 pump gear retaining bolts to
25
Nm (18 lbf/ft).
f.Remove timing pins from pump and flywheel
housing.
34.Using a suitable anti-seize compound, fit the
blanking plug to flywheel housing. Tighten to
12
Nm (9 lbf/ft).
35.Fit access plate with gasket to front cover plate.
Tighten bolts to
25 Nm (18 lbf/ft).
36.Refit injector pipes.
37.Reconnect battery.

FUEL SYSTEM
3
REPAIR FUEL INJECTORS
Service repair no - 19.60.10
Remove
NOTE: When a fuel injector is considered
to be the cause of irregular running and
loss of power it will be necessary to fit a
donor set of injectors to determine which injector
is at fault. DO NOT attempt to dismantle or carry
out spray tests on the fuel injectors. This work
can only carried out by authorised Bosch dealers.
1.Remove oil filler cap and release sound
insulation cover from top of engine.
2.Disconnect high pressure fuel supply pipes from
injectors and injection pump. Remove in pairs.
3.Disconnect spill return hose(s) from injectors.
4.Plug pipes and injector connections to prevent
the ingress of dirt and foriegn matter.5.Remove retaining nut and release each injector
clamp plate from cylinder head.
6.Remove injector and discard copper washer.
Refit
7.Ensure injectors and seating in cylinder head are
clean.
8.Lightly grease a new copper sealing washer and
position on each injector.
9.Fit injectors in cylinder head with spill return
outlets facing outward.
10.Secure injector with clamp plate and nut. Tighten
nut to
25 Nm (18 lbf/ft).
NOTE: The clamp plates are slightly
curved and should be fitted with the
convex side uppermost.
11.Fit the spill return pipe with a single copper
washer under the head of the banjo bolt and 2
copper washers fitted between the injector and
the banjo. Tighten banjo bolt to
10 Nm (7 lbf/ft).
12.Fit high pressure pipes to injectors and injection
pump. Tighten union nuts to
28 Nm (21 lbf/ft).
13.Fit sound insulation cover and oil filler cap.

19FUEL SYSTEM
6
REPAIR SIDE MOUNTED FUEL TANK
Service repair no - 19.55.05
NOTE: This fuel tank is standard on 90
models and an option on 110/130 2 door
vehicles fitted with twin tanks.
Remove
WARNING: Before any attempt is made to
start the removal procedure it is vital that
the FUEL HANDLING PRECAUTIONS are
carefully studied and implemented in the interests
of safety.
See INTRODUCTION, Information, Fuel
Handling Precautions
1.Disconnect battery.
2.Remove fuel filler cap.3.Remove fuel tank drain plug, allow fuel to drain
into a clean container and refit plug.
4.Remove RH seat cushion.
5.Release retaining catch and remove seat base
cover to gain access to fuel tank.
6.Disconnect electrical plug from fuel gauge unit.
7.Disconnect fuel supply pipe from tank.
8.Disconnect spill return pipe from fuel tank.
9.Disconnect breather pipe from fuel filler tube.
10.Slacken hose clip and remove filler hose from
filler tube.
11.From rear of tank, remove 2 nuts and washers
securing tank mounting to captive-headed bolts.
12.Support rear of fuel tank and remove captive
bolts.

FUEL SYSTEM
7
REPAIR REV: 05/99
13.Remove single bolt fixing assembly securing
front of tank to chassis mounted bracket.
14.Remove 3 bolts securing tank mounting bracket
to chassis and release bracket.
15.Lower front of tank while turning anti-clockwise
and remove from vehicle.
16.If required, remove tank gauge unit.
See
INSTRUMENTS, Repair, Fuel gauge tank unit
- side fuel tank
orSee INSTRUMENTS,
Repair, Fuel gauge tank unit - rear fuel tank,
110/130
Refit
17.Fit filler hose and clip to tank but do not fully
tighten. Position clip screw so that it is
accessible when tank is fitted.
18.Fit breather hose and secure with clip.
19.Position fuel tank in vehicle and loosely secure
front mounting bracket to tank with special bolt
and rubber bushes.
20.Secure mounting bracket to chassis with 3 bolts
and fully tighten to
20 Nm (15 lbf/ft).
21.Secure rear of tank to chassis mounting and
tighten captive bolt plate fixings to
20 Nm (15
lbf/ft).
22.Fully tighten front fixing bolt assembly to20 Nm
(15 lbf/ft).
23.Fit spill return and fuel supply pipes and secure
union connections.
24.Fit fuel level unit electrical plug.
25.Fit hose to filler tube and tighten upper and lower
clips.
26.Check that drain plug is secure and fill fuel tank.
27.Reconnect battery.
28.Prime fuel system
See Adjustment, Priming
the fuel system
and start engine.
29.Check system for leaks and operation of fuel
gauge.
30.Fit seat base cover and seat cushion.SIDE MOUNTED FUEL TANK - 5 DOOR VEHICLES
Service repair no - 19.55.01
NOTE: This fuel tank is used on 110/130 5
door vehicles fitted with a twin tank
option.
WARNING: Before any attempt is made to
start the removal procedure it is vital that
the FUEL HANDLING PRECAUTIONS,
See
INTRODUCTION, Information, Fuel handling
precautions
are carefully studied and
implemented in the interests of safety.
Remove
1.Disconnect battery.
2.Remove tank drain plug, allow fuel to drain into a
clean container, and refit plug.
3.Remove RH seat cushion.
4.Remove retaining catch and remove seat base
cover to gain access to fuel tank.
5.Disconnect electrical plug from fuel gauge unit.
6.Disconnect fuel supply pipe from tank.
7.Disconnect spill return pipe from tank.
8.Remove 3 bolts securing tank to front mounting
bracket.
9.Support front of tank and remove single fixing
assembly securing tank to rear mounting
bracket.
10.Remove tank from vehicle.
11.If required, remove fuel gauge unit.
See
INSTRUMENTS, Repair, Fuel gauge tank unit
- side fuel tank
orSee INSTRUMENTS,
Repair, Fuel gauge tank unit - rear fuel tank,
110/130
Refit
12.Position fuel tank in vehicle and loosely secure
to rear mounting bracket with special bolt and
rubber bushes.
13.Secure tank to front mounting bracket and
tighten fixings to
20 Nm (15 lbf/ft).
14.Fully tighten rear fixing bolt assembly to20 Nm
(15 lbf/ft).
15.Fit spill return and fuel supply pipes to fuel tank
and securely tighten union connectios.
16.Fit electrical plug to fuel gauge unit.
17.Check that drain plug is secure and fill fuel tank.
18.Reconnect battery.
19.Prime fuel system.
See Adjustment, Priming
the fuel system
and start engine.
20.Check system for leaks and operation of fuel
gauge.
21.Fit seat base cover and seat cushion.

19FUEL SYSTEM
8
REPAIR REAR MOUNTED FUEL TANK - 110/130
Service repair no - 19.55.26
WARNING: Before any attempt is made to
start the removal procedure it is vital that
the FUEL HANDLING PRECAUTIONS
See
INTRODUCTION, Information, FUEL HANDLING
PRECAUTIONS
are carefully studied and
implemented in the interests of safety.
Remove
1.Disconnect battery.
2.Remove fuel filler cap.
3.Remove tank drain plug, allow fuel to drain into a
clean container, and refit plug.
4.Slacken retaining clips and disconnect fuel filler
hose from rear tank.5.Disconnect breather hose from filler tube.
6.Disconnect electrical plug and fuel supply pipe
from outlet pipe union on fuel gauge unit.
7.If the vehicle is fitted with a tow ball drop-plate
with support bars, the bars must be removed.
8.Remove anti-roll bar chassis mountings.
See
REAR SUSPENSION, Repair, Anti-roll bar
and push roll bar down to provide access to the
tank.
9.Remove LH lashing eye to assist access to tank.
10.Position a support under the tank, preferably one
that can be progressively lowered.

MANIFOLD AND EXHAUST SYSTEM
1
REPAIR INDUCTION MANIFOLD
Service repair no - 30.15.02
Remove
1.Disconnect battery.
2.Remove oil filler cap and remove rocker cover
insulation.
3.Remove hose intercooler to induction manifold. If
fitted, remove EGR valve.
See FUEL SYSTEM,
Repair, EGR valve
4.Remove 2 screws and release heat shield from
induction manifold.
5.Slacken induction manifold lower securing nuts,
located below exhaust manifold.
6.Remove induction manifold upper securing bolts.
7.Remove induction manifold. Plug apertures in
cylinder head with clean rag to prevent any items
falling into engine.
8.Check gasket is satisfactory for further use.
Refit
9.Clean induction manifold mating face.
10.Position induction manifold and secure with
upper and lower fixings.
11.Tighten securing nuts and bolts to
25 Nm (18
lbf/ft).
12.Fit manifold heat shield.
13.Fit hose intercooler to induction manifold.
14.Fit rocker cover insulation.
15.Reconnect battery.INDUCTION/EXHAUST MANIFOLD GASKET
Service repair no - 30.15.15
Remove
1.Remove induction manifold
See Induction
manifold
.
2.Remove turbocharger outlet hose.
3.Raise vehicle and slacken exhaust front pipe to
intermediate silencer flange nuts. Ensure pipe is
free to turn.
NOTE: If removing exhaust manifold and
turbocharger assembly from vehicle,
remove manifold to exhaust front pipe
nuts while working under vehicle.
4.Remove exhaust manifold securing nuts,
removing centre lower nut first.
5.Move heater rail clear of exhaust manifold.
6.With exhaust manifold and turbocharger still
attached to exhaust front pipe, withdraw from
head by turning front pipe until sufficient access
is gained to remove gasket.
7.Suitably support exhaust manifold and
turbocharger assembly to prevent damage.
8.Remove induction manifold lower nuts.
9.Remove gasket.
10.Clean mating faces.

ELECTRICAL
25
REPAIR DIGITAL DIESEL SHUT-OFF VALVE (DDS)
Service repair no - 86.77.00
Remove
1.Remove fuel injection pump
See FUEL
SYSTEM, Repair, Fuel injection pump.
2.Drill out 2 shear bolts securing DDS valve and
clamp, using a 3.2 mm drill, to a depth of
approximately 5 mm.
CAUTION: Use a drill bushing to guide the
drill.
3.Using an extractor, remove the 2 DDS valve
retaining bolts and discard.
4.Release DDS valve from fuel shut-off solenoid.
5.Remove protective cap from shut-off solenoid.
6.Unscrew terminal nut, release terminal lead
eyelet and remove DDS valve.7.Remove protective cap retainer and release
DDS valve clamp from behind fuel shut-off
solenoid.
Refit
8.Position DDS valve clamp behind fuel shut-off
solenoid and fit protective cap retainer.
9.Fit DDS terminal lead to fuel shut-off solenoid.
Tighten nut to
2 Nm (1.5 lbf/ft).
10.Fit protective cap to fuel shut-off solenoid,
ensuring terminal lead is correcly routed on RH
side of cap.
11.Secure DDS valve to fuel cut-off solenoid and
clamp. Tighten new shear bolts progressively
until heads shear.
12.Fit fuel injection pump
See FUEL SYSTEM,
Repair, Fuel injection pump.

88INSTRUMENTS
4
REPAIR PRINTED CIRCUIT - WARNING LIGHT PANEL
Service repair no - 88.20.20
Remove
1.Remove warning light panel
See Warning light
panel
.
2.Remove 13 illumination bulb holders from light
panel.
3.Release printed circuit from locating pins and
remove from panel seatings.
Refit
4.Fit new printed circuit over panel seatings and
position on locating pins.
5.Fit illumination bulbs to secure circuit.
6.Fit warning light panel
See Warning light
panel
.FUEL GAUGE TANK UNIT - REAR FUEL TANK,
110/130
Service repair no - 88.25.30
WARNING: Ensure that fuel handling
precautions given in Section 01 -
Introduction are strictly adhered to when
carrying out the following instructions.
Remove
1.Disconnect battery.
2.Remove fuel filler cap.
3.Remove tank drain plug, allow fuel to drain into a
clean container, and refit plug.
4.On LH side of tank, disconnect fuel supply pipe
from outlet pipe on fuel gauge unit.
5.Disconnect electrical plug from fuel gauge unit.
6.Release locking ring and withdraw fuel gauge
unit from tank, complete with sealing ring.
Refit
7.Insert gauge unit into tank with float positioned to
base of tank. Fit new sealing washer, if
necessary.
8.Secure gauge unit with locking ring.
9.Fit electrical plug and reconnect fuel supply pipe.
10.Refill fuel tank.
11.Reconnect battery.