maintenance LAND ROVER DEFENDER 1996 Owner's Manual

10MAINTENANCE
14
MAINTENANCEREV: 05/99 ADDITIONAL MAINTENANCE SCHEDULES
Camshaft drive belt
The engine timing gears are driven by a toothed
rubber belt which must be renewed at intervals
determined by the severity of operating conditions. In
reasonable, temperate climate operation, the belt
should be renewed every 120,000 km (72,000 miles)
or every six years whichever occurs earlier.
In adverse operating conditions, such as work in dusty
atmospheres, high ambient temperatures, desert and
tropical zones, renew the belt every 60,000 km
(36,000 miles) or every three years, whichever occurs
earlier.
CAUTION: If the drive belt is not renewed
at the correct interval, it could fail,
resulting in serious engine damage.
Oil change diesel engines
If the vehicle is operated on fuel with a high sulphur
content (over 1%) the oil change intervals must not
exceed 5000 km (3000 miles).
Anti-freeze
At two yearly intervals or at the onset of the second
winter, the cooling system should be drained, flushed
and refilled with the required water and anti-freeze
solution.
Hydraulic brake fluid.
It is recommended that at 40,000 km (24,000 miles)
intervals or every two years, whichever is the earlier,
the hydraulic brake fluid should be completely
renewed.
At 80,000 km (48,000 miles) intervals or every four
years, whichever is the earlier, all hydraulic brake fluid
seals and flexible hoses should be renewed. All
working surfaces of the master cylinder and caliper
cylinders should be examined and renewed where
necessary.Air cleaner
When the vehicle is used in dusty or field conditions or
deep wading, frequent attention to the air cleaner may
be required.
Dampers
At 60,000 km (36,000 miles) intervals remove all
suspension dampers, test for correct operation, refit or
renew as necessary.
SPECIAL OPERATING CONDITIONS
When the vehicle is operated in extremely arduous
conditions or on dusty, wet or muddy terrain, more
frequent attention should be paid to all servicing
requirements.
Additional daily or weekly attention depending on
operating conditions:
Check/top-up transfer box oil.
Check steering rubber boots for security and
condition. Renew if damaged.
Check brake fluid level: Investigate cause if any fluid
loss is suspected.
Clean brake discs and calipers.
Lubricate front and rear propeller shaft
universal/sliding joints. Under tropical or severe
conditions, particularly where sand is encountered,
the sliding joints must be lubricated very frequently to
prevent ingress of abrasive material.
Every week and every maintenance inspection check
tyre pressures and inspect tyre treads and side walls.
Under arduous cross-country conditions the tyre
pressures should be checked much more frequently,
even to the extent of a daily check.
Monthly
Renew gearbox oil.
Renew transfer box oil.
Check air cleaner element and renew every 6 months
or as necessary.

MAINTENANCE
15
MAINTENANCE ADDITIONAL MAINTENANCE SCHEDULES
Camshaft drive belt
The engine timing gears are driven by a toothed
rubber belt which must be renewed at intervals
determined by the severity of operating conditions. In
reasonable, temperate climate operation, the belt
should be renewed every 120,000 km (72,000 miles)
or every six years whichever occurs earlier.
In adverse operating conditions, such as work in dusty
atmospheres, high ambient temperatures, desert and
tropical zones, renew the belt every 60,000 km
(36,000 miles) or every three years, whichever occurs
earlier.
CAUTION: If the drive belt is not renewed
at the correct interval, it could fail,
resulting in serious engine damage.
Oil change diesel engines
If the vehicle is operated on fuel with a high sulpher
content (over 1%) the oil change intervals must not
exceed 5000 km (3000 miles).
Anti-freeze
At two yearly intervals or at the onset of the second
winter, the cooling system should be drained, flushed
and refilled with the required water and anti-freeze
solution.
Hydraulic brake fluid.
It is recommended that at 40,000 km (24,000 miles)
intervals or every two years, whichever is the earlier,
the hydraulic brake fluid should be completely
renewed.
At 80,000 km (48,000 miles) intervals or every four
years, whichever is the earlier, all hydraulic brake fluid
seals and flexible hoses should be renewed. All
working surfaces of the master cylinder and caliper
cylinders should be examined and renewed where
necessary.Air cleaner
When the vehicle is used in dusty or field conditions or
deep wading, frequent attention to the air cleaner may
be required.
Dampers
At 60,000 km (36,000 miles) intervals remove all
suspension dampers, test for correct operation, refit or
renew as necessary.
SPECIAL OPERATING CONDITIONS
When the vehicle is operated in extremely arduous
conditions or on dusty, wet or muddy terrain, more
frequent attention should be paid to all servicing
requirements.
Additional daily or weekly attention depending on
operating conditions:
Check/top-up transfer box oil.
Check steering rubber boots for security and
condition. Renew if damaged.
Check brake fluid level: Investigate cause if any fluid
loss is suspected.
Clean brake discs and calipers.
Lubricate front and rear propeller shaft
universal/sliding joints. Under tropical or severe
conditions, particularly where sand is encountered,
the sliding joints must be lubricated very frequently to
prevent ingress of abrasive material.
Every week and every maintenance inspection check
tyre pressures and inspect tyre treads and side walls.
Under arduous cross-country conditions the tyre
pressures should be checked much more frequently,
even to the extent of a daily check.
Monthly
Renew gearbox oil.
Renew transfer box oil.
Check air cleaner element and renew every 6 months
or as necessary.

19FUEL SYSTEM
12
REPAIR HEATER PLUG CONTROL UNIT
Service repair no - 19.60.33
Remove
1.Disconnect battery.
2.Remove screw securing control unit to bulkhead.
3.Disconnect multi-plug and release control unit.
Refit
4.Fit harness multi-plug to control unit.
5.Secure control unit to bulkhead.
6.Reconnect battery.AIR CLEANER
Service repair no - 19.10.01
Remove
1.Slacken hose clip and detach outlet hose.
2.Release clips and open air cleaner retaining
straps.
3.Lift up air cleaner, slacken hose clip and detach
inlet hose.
4.Remove air cleaner.
Refit
5.Position air cleaner and connect inlet hose.
6.Close air cleaner retaining straps and secure
lock clips.
7.Connect outlet hose.
NOTE: If an EGR fuel system is fitted,
ensure the modulator valve vacuum spill
pipe is secure in the outlet hose.
AIR CLEANER ELEMENT
Service repair no - 19.10.10
For remove and refit procedure.
See SECTION 10,
Maintenance, Under bonnet maintenance

19FUEL SYSTEM
14
REPAIR TURBOCHARGER INLET HOSE
Service repair no - 19.42.11
Remove
1.Disconnect battery.
2.Slacken retaining clip and disconnect intake
hose from turbocharger.
3.Slacken retaining clip and disconnect hose from
air cleaner.
4.If fitted, disconnect EGR modulator valve
vacuum spill pipe from inlet hose.
5.Slacken retaining clip and disconnect breather
valve hose from inlet hose.
6.Remove inlet hose.
Refit
7.Fit inlet hose to air cleaner.
8.Fit cyclone breather hose to inlet hose.
9.If applicable, fit vacuum spill pipe to inlet hose.
10.Fit inlet hose to turbocharger.
11.Reconnect battery.TURBOCHARGER OIL FEED PIPE
Service repair no - 19.42.14
Remove
1.Disconnect battery.
2.Remove exhaust front pipe.
See MANIFOLD
AND EXHAUST SYSTEM, Repair, Exhaust
front pipe
3.Remove banjo bolt securing oil feed pipe to
turbocharger and discard 2 joint sealing
washers.
4.Unscrew union and remove feed pipe from
cylinder block.
5.Plug connections to prevent ingress of dirt.
Refit
6.Using new joint washer, fit oil feed pipe to
cylinder block. Tighten union connector to
25
Nm (18 lbf/ft).
7.Fit a new joint washer to both sides of banjo and
secure feed pipe to turbocharger. Tighten banjo
bolt to
20 Nm (15 lbf/ft).
8.Fit exhaust front pipe.See MANIFOLD AND
EXHAUST SYSTEM, Repair, Exhaust front
pipe
9.Check/top-up engine oil level.See SECTION
10, Maintenance, Under bonnet maintenance
10.Reconnect battery.

FUEL SYSTEM
15
REPAIR TURBOCHARGER OIL DRAIN PIPE
Service repair no - 19.42.12
Remove
1.Disconnect battery.
2.Remove exhaust front pipe.
See MANIFOLD
AND EXHAUST SYSTEM, Repair, Exhaust
front pipe
3.Unscrew union and disconnect oil drain pipe
from cylinder block.
4.Remove 2 bolts securing oil drain pipe to
turbocharger.
5.Remove drain pipe and discard gasket.
6.Plug connections to prevent ingress of dirt.
Refit
7.Ensure mating surfaces of oil pipe, turbocharger
and engine block are clean.
8.Using new gasket, fit oil drain pipe to
turbocharger. Tighten bolts to
25 Nm (18 lbf/ft).
9.Fit drain pipe to cylinder block and tighten union
connector to
38 Nm (28 lbf/ft).
10.Fit exhaust front pipe.See MANIFOLD AND
EXHAUST SYSTEM, Repair, Exhaust front
pipe
11.Check/top-up engine oil level.See SECTION
10, Maintenance, Under bonnet maintenance
12.Reconnect battery.

COOLING SYSTEM
7
REPAIR EXPANSION TANK
Service repair no - 26.15.01
Remove
1.Position container to collect coolant spillage.
2.Slacken retaining clips and disconnect both
hoses from base of expansion tank.
3.Remove 3 bolts securing expansion tank to
inside wing and mounting bracket.
4.Remove expansion tank.
Refit
5.Fit expansion tank to inside wing and mounting
bracket.
6.Fit both hoses to base of tank.
7.Check and top up cooling system
See
SECTION 10, Maintenance, Under bonnet
maintenance

37MANUAL GEARBOX
2
REPAIR
10.Remove 3 trim studs and lift up handbrake
gaiter.
11.Remove split pin, clevis pin, washer and
disconnect cable from handbrake lever. Ensure
handbrake is off.
12.Drain cooling system
See COOLING SYSTEM,
Adjustment, Drain and refill cooling system
.
13.Remove viscous fan unit
See COOLING
SYSTEM, Repair, Viscous coupling and fan
.
14.Slacken retaining clip and disconnect radiator
top hose at thermostat housing.
15.Slacken retaining clip and disconnect intake
hose at induction manifold. If EGR system is
fitted, slacken 2 retaining clips and disconnect
intake hose at intercooler.
16.Slacken retaining clip and disconnect hose at
turbocharger.
17.Remove bolt securing transmission breather
pipe clip to rear of engine.
18.Release breather pipes.
19.Release ties securing gearbox harness to
breather pipes.
20.Raise vehicle on ramp.
21.Position a suitable container under transmission
and drain main gearbox and transfer box
See
MAINTENANCE , Under vehicle maintenance
.
22.Mark front propeller shaft drive flange and
transfer box output flange for reassembly.
23.Remove 4 nuts and disconnect propeller shaft
from transfer box.

37MANUAL GEARBOX
6
REPAIRREV: 05/99 78.Position crossmember and locate over fixing
studs of LH and RH gearbox mounting rubbers.
79.Align crossmember and secure to chassis with 4
nuts and bolts on each side.
NOTE: Fit battery earth strap retaining clip
to LH top bolt.
80.Fit intermediate silencer.
See MANIFOLD AND
EXHAUST SYSTEM, Repair, Intermediate
pipe - 90
orSee MANIFOLD AND EXHAUST
SYSTEM, Repair, Intermediate pipe - 110/130
.
81.Fit front pipe to exhaust manifold
See
MANIFOLD AND EXHAUST SYSTEM, Repair,
Exhaust front pipe
.
82.Fit rear propeller shaft to transmission brake
drum. Tighten nuts to
47 Nm (33 lbf/ft).
83.Remove 3 bolts securing support cradle to
transmission and remove hoist.
84.Reconnect battery earth strap to transfer box
fixing.
85.Connect speedometer cable to transfer box and
secure with retaining clip.
86.Coat both sides of clutch slave clinder backing
plate with Hylomar P232M waterproof sealant.
87.Locate backing plate on slave cylinder.
88.Fit slave cylinder to bell housing, engaging
push-rod through centre of dust cover, and with
bleed screw uppermost. Tighten bolts to
25 Nm
(18 lbf/ft).
89.Fit front propeller shaft to transfer box. Tighten
nuts to
47 Nm (33 lbf/ft).
90.Refill main gearbox and transfer boxSee
MAINTENANCE , Under vehicle maintenance
.
91.Feed transmission brake cable through heel
board and ensure grommet is correctly located.
NOTE: Apply a soap solution to aid fitment
of cable.
92.Lower vehicle on ramp.
93.Fit ties to secure gearbox harness to
transmission breather pipes.
94.Fit breather pipe retaining clip to rear of engine.
95.Reconnect charge air hose at turbocharger.
96.Reconnect intake hose at induction manifold. If
EGR system is fitted, reconnect intake hose at
intercooler.
97.Reconnect radiator top hose at thermostat
housing.
98.Fit viscous fan unit
See COOLING SYSTEM,
Repair, Viscous coupling and fan
.
99.Reconnect battery.100.Refill cooling system
See COOLING SYSTEM,
Adjustment, Drain and refill cooling system
.
101.Connect cable clevis to handbrake lever and fit
handbrake gaiter.
102.Locate insulation pad over gear levers and fit to
tunnel cover.
103.Fit gear lever with gaiter to lower lever spline
and secure with retaining nut.
104.Fit gear lever cover.
105.Fit gear lever and transfer box lever knobs.
106.Fit gearbox cover carpet.
107.Check operation of handbrake and adjust as
necessary
See MAINTENANCE , Under
vehicle maintenance
.

41TRANSFER GEARBOX
2
FAULT DIAGNOSIS OIL LEAKS
Verify that oil leak is from transfer box and not main
gearbox before proceeding with checks.
Prior to road test
1.Check oil level in transfer box is correct.
2.Check tightness of level and drain plugs.
3.Check breather system for blockage. To validate
system pipe must be removed, inspected,
rectified as necessary and refitted.
4.Remove all traces of oil from exterior of transfer
box.
Take vehicle for short road test.
5.Identify source of leaks and rectify as follows.
Front or rear output seal leaking:-
1.Drain oil and remove leaking output flange.
2.Inspect seal track on flange for surface damage.
If damaged renew component.
3.Remove and discard oil seal.
4.Inspect seal locating bore and remove any sharp
edges which may damage new oil seal.
5.Fit new seal.
6.Fit output flange and all other parts.
7.Add oil to correct level into gearbox
See
SECTION 10, Maintenance, Under vehicle
maintenance
.
Cover plate sealant leaking.
1.Drain oil and remove leaking cover plate.
2.Remove all traces of joint sealant from both joint
faces.
3.Degrease all components and apply a thin film of
Hylomar sealant, to both joint faces.
4.Apply thread sealant to bolts which come into
contact with gearbox oil.
5.Refit cover plate.
CAUTION: Care must be taken not to
overtighten fixings.Leak between main and transfer gearboxes.
1.Site vehicle onto a ramp .
2.Select neutral in transfer box and select 4th gear
in main gearbox.
3.Run engine at 2000 rpm with clutch/drive
engaged.
4.Observe joint between main and transfer boxes.
5.If oil leak is found establish if it is gear oil.
6.If so, leak is originating from transfer box.
7.Check two inner (main/transfer) bolts are oil
tight, as these holes are tapped into main
transfer case.
8.Remove transfer box to inspect mainshaft collar
seal track condition, and front face of transfer
case for porosity
See Repair, Transfer
gearbox
.
9.If these areas require servicing, transfer gearbox
input seal must also be renewed.
CAUTION: Avoid damaging new seal lip
and ensure seal is fitted flush with
machined face. Also ensure new seal is
not damaged when refitting transfer gearbox.
10.If red ATF type oil is seen leaking during
workshop test, investigate main gearbox for
cause of leak.
Detent plug or electrical switch leaks.
1.Detent plugs and electrical switches do not
usually leak. It must be noted that they fit into
open tapped holes in transfer case and therefore
should be considered when looking for source of
leak.

41TRANSFER GEARBOX
2
REPAIR
11.Remove 3 trim studs and lift up handbrake
gaiter.
12.Remove split pin, clevis pin, washer and
disconnect cable from handbrake lever. Ensure
handbrake is off.
13.Release handbrake outer cable from heelboard.
14.Remove fan cowl
See COOLING SYSTEM,
Repair, Fan cowl
.
15.Raise vehicle on ramp.
16.Drain transfer box oil
See SECTION 10,
Maintenance, Under vehicle maintenance
.
17.Remove intermediate silencer.
See MANIFOLD
AND EXHAUST SYSTEM, Repair,
Intermediate pipe - 90
orSee MANIFOLD
AND EXHAUST SYSTEM, Repair,
Intermediate pipe - 110/130
.
18.Mark rear propeller shaft drive flange and
transmission brake drum for reassembly.
19.Remove 4 nuts, disconnect propeller shaft from
brake drum, and tie aside.
20.Mark front propeller shaft drive flange and
transfer box output flange for reassembly.
21.Remove 4 nuts, disconnect propeller shaft from
transfer box, and tie aside.
22.Remove retaining clip at lower end of pivot arm
and disconnect differential lock control operating
rod.