manual transmission LAND ROVER DEFENDER 1996 Workshop Manual

INTRODUCTION
11
INFORMATION VEHICLE IDENTIFICATION NUMBER (VIN)
The Vehicle Identification Number and the
recommended maximum vehicle weights are stamped
on a plate riveted to the brake pedal box in the engine
compartment. The VIN is also stamped on a plate
visible through the LH side of the windscreen, see
J6088.
A.Type approval
B.Identification
C.Maximum permitted laden weight for vehicle
D.Maximum vehicle and trailer weight
E.Maximum road weight-front axle
F.Maximum road weight-rear axle
The number is also stamped on the RH side of the
chassis to the rear of the front lashing eye, see J6089.
The Vehicle Identification Number identifies the
manufacturer, model range, wheel base, body type,
engine, steering, transmission, model year and place
of manufacture. The following example shows the
coding process.
SALLDHMF7TA
SAL= World manufacturer identifier
LD= Land Rover Defender
H= 110 inch,V= 90inch,K= 130 inch
M= 4 door Station Wagon,A= 90 Soft Top, Hard Top,
Pick-up,B= 2 door Station Wagon,E= 2 door 130
Crew cab,F= 4 door 130 Crew cab,H= 130 High
Capacity Pick-up
F= 2.5L (300Tdi)
7= RH drive, 5 speed manaul,8= LH drive, 5 speed
manual
T= 1996 MY, volume build,N= 1996 MY, non-volume
build
A= Solihull build,F= CKD, assembled locally from kit

MANUAL GEARBOX
1
FAULT DIAGNOSIS R380 GEARBOX
Symptom - Gear jumps out of engagement (any
forward gear)
1.Check condition and security of transmission
and engine mountings.
2.Check in situ, gear lever and selector
adjustments
See Adjustment, Gear change
lever bias spring - adjust
andSee
Adjustment, Fifth gear stop screw adjust
.
3.In situ, remove gearshift and check selector rail
yoke security.
Also check selector detent spring tension and
both spool retainers.
Suspect internal fault, see Overhaul Manual.
4.Check action/operation of main selector rail and
forks.
5.Check condition of synchromesh and gear dog
teeth.
6.Check main and layshaft end floats bearings and
adjustments.
7.Check condition of all gearbox components,
ensure clearances and adjustments are correct
on reassembly.
Symptom - Reverse gear only jumps out of
engagment
1.Check condition and security of transmission
and engine mountings.
2.Check in situ, gear lever and selector
adjustments
See Adjustment, Gear change
lever bias spring adjust
andSee Adjustment,
Fifth gear stop screw adjust
.
3.In situ, remove gearshift and check selector rail
yoke security.
Also check selector detent spring tension and
both spool retainers.
Suspect internal fault, see Overhaul Manual.
4.Check action/operation of main selector rail and
reverse lever.
5.Check condition of reverse gear, angled
bearings and shaft.
6.Check condition of all gearbox components,
ensure clearances and adjustments are correct
on reassembly.Symptom - Excessive force required to engage or
change gear, vehicle stationary or moving.
1.Check lubricant specification and level, if low do
not top up at this stage.
2.In situ, lubricate gear mechanism, and check
selector adjustments
See Adjustment, Gear
change lever bias spring - adjust
andSee
Adjustment, Fifth gear stop screw adjust
.
3.In situ, remove gearshift and check selector rail
is free and that the yoke is secure. Also check
selector detent spring tension and both spool
retainers.
4.Drain lubricant and check for contamination or
metal particles.
Suspect worn synchromesh unit or baulk rings
on affected gears, see Overhaul Manual.
Symptom - Noisy gear engagement, vehicle
stationary
See CLUTCH, Fault diagnosis, Clutch
Noise - Mechanical Faults
.
Symptom - Noisy gear selection, vehicle moving.
1.Confirm that clutch operation is satisfactory.
2.Establish which gear/gears is causing noise.
3.Check lubricant specification and level, if low do
not top up at this stage.
4.Drain lubricant and check for contamination or
metal particles.
Suspect worn synchromesh, see Overhaul
Manual.
5.Check condition of synchromesh unit, springs
and cones for distortion and wear. Also check
dog teeth for damage and cone mating surface
on gear for signs of overheating.
6.Check condition of all gearbox components,
ensure clearances and adjustments are correct
on reassembly.
Symptom - Noise from gearbox in neutral, which
changes tone or becomes worse when clutch is
depressed,
See CLUTCH, Fault diagnosis, Clutch
Noise - Mechanical Faults
.
Symptom - Noise from gearbox in neutral, which
disappears when clutch is depressed.
1.Check lubricant specification and level, if low do
not top up at this stage.
2.Drain lubricant and check for contamination or
metal particles.
Suspect worn bearings on layshaft, primary shaft
or front of main shaft, see Overhaul Manual.

MANUAL GEARBOX
1
REPAIR REV: 05/99 R380 GEARBOX
Service repair no - 37.20.51
Remove
The R380 gearbox should be removed from
underneath the vehicle, using a hydraulic hoist and
support plateLRT-99-007.
WARNING: Where the use of a
transmission hoist is necessary, it is
absolutely essential to follow the
manufacturer's instructions to ensure safe and
effective use of equipment.
NOTE: A chassis undertray may be fitted
on some vehicle derivatives to conform to
legal requirements. When under chassis
remove and refit procedures are required, it may
be necessary to remove the undertray
See
CHASSIS AND BODY, Repair, Front undertray
or
See CHASSIS AND BODY, Repair, Rear undertray
.
1.Install vehicle on a ramp.
2.Disconnect battery.
3.Remove gearbox carpet.
4.Remove gear lever and transfer box lever knobs.
5.Remove gear lever cover.
6.Remove nut and washer securing gear lever.
7.Mark gear lever spline setting and remove lever
and gaiter from the splined lower gear lever.
8.Release insulation pad from tunnel cover and
gear levers and remove.
9.Select low range on transfer box lever to prevent
lever from fouling tunnel when removing
gearbox.

37MANUAL GEARBOX
2
REPAIR
10.Remove 3 trim studs and lift up handbrake
gaiter.
11.Remove split pin, clevis pin, washer and
disconnect cable from handbrake lever. Ensure
handbrake is off.
12.Drain cooling system
See COOLING SYSTEM,
Adjustment, Drain and refill cooling system
.
13.Remove viscous fan unit
See COOLING
SYSTEM, Repair, Viscous coupling and fan
.
14.Slacken retaining clip and disconnect radiator
top hose at thermostat housing.
15.Slacken retaining clip and disconnect intake
hose at induction manifold. If EGR system is
fitted, slacken 2 retaining clips and disconnect
intake hose at intercooler.
16.Slacken retaining clip and disconnect hose at
turbocharger.
17.Remove bolt securing transmission breather
pipe clip to rear of engine.
18.Release breather pipes.
19.Release ties securing gearbox harness to
breather pipes.
20.Raise vehicle on ramp.
21.Position a suitable container under transmission
and drain main gearbox and transfer box
See
MAINTENANCE , Under vehicle maintenance
.
22.Mark front propeller shaft drive flange and
transfer box output flange for reassembly.
23.Remove 4 nuts and disconnect propeller shaft
from transfer box.

MANUAL GEARBOX
3
REPAIR
24.Remove 2 bolts, withdraw clutch slave cylinder
and backing plate from bell housing, and tie
aside.
25.Mark rear propeller shaft drive flange and
transmission brake drum for reassembly.
26.Remove 4 nuts, disconnect propeller shaft from
brake drum, and tie aside.
27.Remove front pipe from exhaust manifold
See
MANIFOLD AND EXHAUST SYSTEM, Repair,
Exhaust front pipe
.
28.Remove intermediate silencer.
See MANIFOLD
AND EXHAUST SYSTEM, Repair,
Intermediate pipe - 90
orSee MANIFOLD
AND EXHAUST SYSTEM, Repair,
Intermediate pipe - 110/130
29.Temporarily support transmission.
30.Remove nut securing gearbox LH mounting
rubber to chassis crossmember.
31.Remove 4 nuts and bolts securing crossmember
to chassis longitudinals.
32.Remove nut securing transfer box mounting
rubber to RH side of crossmember.
33.Remove 4 nuts and bolts securing crossmember
to chassis longitudinals.
34.With assistance and using a body jack between
chassis longitudinals, jack chassis sufficiently to
enable removal of crossmember.
35.Remove chasss crossmember.
36.Remove 4 bolts from both sides and remove LH
and RH mounting brackets.

37MANUAL GEARBOX
4
REPAIR
37.Pull handbrake cable through heel board and tie
aside.
38.Remove retaining nut, release clamp, and
disconnect speedometer cable from transfer box.
39.Release speedometer cable from retaining clip
on transfer box.
40.Remove retaining nut and release battery earth
strap from transfer box.
41.Secure manufactured cradleLRT-99-007to a
suitable hydraulic hoist.
42.Raise hoist and secure to gearbox with 3 bolts in
location provided.
43.Lower hoist sufficiently to allow transfer lever to
clear transmission tunnel aperture.
44.Disconnect differential lock switch and reverse
light connectors.
45.Remove bolt and release earth leads from RH
side of transfer box.
46.Support engine under sump with a jack.
47.Remove 14 bell housing to engine fixings.
48.Withdraw transmission whilst ensuring all
connections to engine and chassis are released.
49.Lower hoist and remove gearbox assembly.

MANUAL GEARBOX
5
REPAIR Separating transfer gearbox from main gearbox
50.Remove transmission assembly from hoist
cradle and position safely on a bench.
51.Remove breather pipes. Discard pipe union
sealing washers.
52.Remove 'Nyloc' nut, and remove bolt, securing
lever to high/low shaft.
53.Collect spacer washer.
54.Remove 2 clips and remove differential lock
lever link.
55.Remove lower locknut from high/low operating
rod.
56.Place a sling round transfer box and attach to
hoist.
57.Remove nut and 4 bolts securing transfer
gearbox to extension housing.
58.Withdraw transfer gearbox.
Assembling transfer gearbox to main gearbox
59.Clean extension housing and transfer gearbox
mating faces.
60.Ensuring loose upper dowel is fitted, hoist
transfer gearbox into position.
61.Secure transfer box to extension housing.
Tighten fixings to
40 Nm (30 lbf/ft).
62.Connect high/low operating rod, fit and tighten
locknut.
63.Fit link to differential lock lever and secure with 2
clips
64.Align lever to high/low shaft, position washer, fit
bolt and new Nyloc nut. Tighten to
2 Nm (1.5
lbf/ft).
65.Position breather pipes, secure pipe unions
using new sealing washers. Tighten unions to
15
Nm (11 lbf/ft).
Fitting transfer gearbox and main gearbox
assembly
66.Position transmission assembly to hoist cradle.
67.Clean bell housing and engine mating faces.
Apply sealant to both mating faces.
68.Temporarily fit gear lever and select any gear in
main gearbox to facilitate entry of gearbox input
shaft. Engage low range.
69.Position and raise hoist, fit transmission to
engine whilst keeping harness and pipes clear to
prevent trapping.
70.Secure transmission to engine. Tighten fixings to
45 Nm (33 lbf/ft).
71.Secure earth leads to RH side of transfer box.
72.Connect reverse lamp switch connectors and
differential lock switch connectors.
73.Secure breather pipes to harness with clips.
74.Remove support from engine sump.
75.Position temporary support under transmission.
76.Secure LH and RH mounting brackets to
gearbox. Tighten fixings to
55 Nm (41 lbf/ft).
77.With assistance and using a body jack between
chassis longitudinals, jack chassis sufficiently to
enable fitment of crossmember.

37MANUAL GEARBOX
6
REPAIRREV: 05/99 78.Position crossmember and locate over fixing
studs of LH and RH gearbox mounting rubbers.
79.Align crossmember and secure to chassis with 4
nuts and bolts on each side.
NOTE: Fit battery earth strap retaining clip
to LH top bolt.
80.Fit intermediate silencer.
See MANIFOLD AND
EXHAUST SYSTEM, Repair, Intermediate
pipe - 90
orSee MANIFOLD AND EXHAUST
SYSTEM, Repair, Intermediate pipe - 110/130
.
81.Fit front pipe to exhaust manifold
See
MANIFOLD AND EXHAUST SYSTEM, Repair,
Exhaust front pipe
.
82.Fit rear propeller shaft to transmission brake
drum. Tighten nuts to
47 Nm (33 lbf/ft).
83.Remove 3 bolts securing support cradle to
transmission and remove hoist.
84.Reconnect battery earth strap to transfer box
fixing.
85.Connect speedometer cable to transfer box and
secure with retaining clip.
86.Coat both sides of clutch slave clinder backing
plate with Hylomar P232M waterproof sealant.
87.Locate backing plate on slave cylinder.
88.Fit slave cylinder to bell housing, engaging
push-rod through centre of dust cover, and with
bleed screw uppermost. Tighten bolts to
25 Nm
(18 lbf/ft).
89.Fit front propeller shaft to transfer box. Tighten
nuts to
47 Nm (33 lbf/ft).
90.Refill main gearbox and transfer boxSee
MAINTENANCE , Under vehicle maintenance
.
91.Feed transmission brake cable through heel
board and ensure grommet is correctly located.
NOTE: Apply a soap solution to aid fitment
of cable.
92.Lower vehicle on ramp.
93.Fit ties to secure gearbox harness to
transmission breather pipes.
94.Fit breather pipe retaining clip to rear of engine.
95.Reconnect charge air hose at turbocharger.
96.Reconnect intake hose at induction manifold. If
EGR system is fitted, reconnect intake hose at
intercooler.
97.Reconnect radiator top hose at thermostat
housing.
98.Fit viscous fan unit
See COOLING SYSTEM,
Repair, Viscous coupling and fan
.
99.Reconnect battery.100.Refill cooling system
See COOLING SYSTEM,
Adjustment, Drain and refill cooling system
.
101.Connect cable clevis to handbrake lever and fit
handbrake gaiter.
102.Locate insulation pad over gear levers and fit to
tunnel cover.
103.Fit gear lever with gaiter to lower lever spline
and secure with retaining nut.
104.Fit gear lever cover.
105.Fit gear lever and transfer box lever knobs.
106.Fit gearbox cover carpet.
107.Check operation of handbrake and adjust as
necessary
See MAINTENANCE , Under
vehicle maintenance
.