gearbox LAND ROVER DEFENDER 1996 Owner's Guide

MANUAL GEARBOX
1
ADJUSTMENT GEAR CHANGE LEVER BIAS SPRING - ADJUST
Service repair no - 37.16.26
1.Remove gear lever and transfer box lever knobs.
2.Remove gear lever cover.
3.Remove nut and washer securing gear lever.
4.Mark gear lever spline setting, remove lever and
gaiter from lower lever.
5.Remove insulation pad from tunnel aperture.
6.Fit gear lever and select 3rd or 4th gear.
7.Slacken adjustment screw locknuts.
8.Adjust screws until both legs of bias springs are
approximately 0.5mm clear of gear lever cross
pin.
9.Apply a slight load to gear lever in a LH direction
and adjust RH screw downward until RH spring
leg just makes contact with cross pin.
10.Repeat procedure for LH adjustment screw.
11.Lower both adjustment screws equal amounts
until radial play is eliminated.
12.Tighten locknuts.
13.Return gear lever to neutral position and rock
across gate several times. The gear lever should
return to 3rd and 4th gate.
14.Remove gear lever.
15.Fit insulation pad.
16.Locate gaiter over lower lever and bias springs.
17.Fit gear lever to lower lever spline, secure with
new nyloc nut and tighten to
25 Nm (18 lbf/ft).
18.Fit gear lever cover.
19.Fit gear lever and transfer box lever knobs.

37MANUAL GEARBOX
2
ADJUSTMENT FIFTH GEAR STOP SCREW - ADJUST
Service repair no - 37.16.67
1.Remove gear lever and transfer box lever knobs.
2.Remove gear lever cover.
3.Remove nut and washer securing gear lever.
4.Mark gear lever spline setting, remove lever and
gaiter from lower lever.
5.Remove insulation pad from tunnel aperture.
6.Remove tunnel carpet.
7.Remove retaining screws and release fuse box
cover.
8.Remove 2 screws and release fuse box from
bulkhead to assist next operation.
9.Remove 16 screws securing tunnel cover to
vehicle body.
10.Manouvre tunnel cover to clear handbrake lever
and remove from vehicle.
11.Fit gear lever and knob and select reverse gear.

MANUAL GEARBOX
3
ADJUSTMENT
12.Slacken stop screw locknut.
13.Apply light pressure to gear lever towards LH
side and turn screw clockwise until it abuts yoke.
14.Turn screw anti-clockwise until 25 mm freeplay
is felt at gear lever knob. Ensure 5th gear can be
engaged.
15.Tighten stop screw locknut.
16.Check that all other gears are selectable.
17.Remove gear lever.
18.Manouvre tunnel cover into position and secure
with 16 screws.
19.Fit fuse box and cover.
20.Fit tunnel carpet.
21.Fit insulation pad into tunnel aperture.
22.Locate gaiter over lower lever and bias springs.
23.Fit gear lever to lower lever spline, secure with
new nyloc nut and tighten to
25 Nm (18 lbf/ft).
24.Fit gear lever cover.
25.Fit gear lever and transfer box lever knobs.

MANUAL GEARBOX
1
REPAIR REV: 05/99 R380 GEARBOX
Service repair no - 37.20.51
Remove
The R380 gearbox should be removed from
underneath the vehicle, using a hydraulic hoist and
support plateLRT-99-007.
WARNING: Where the use of a
transmission hoist is necessary, it is
absolutely essential to follow the
manufacturer's instructions to ensure safe and
effective use of equipment.
NOTE: A chassis undertray may be fitted
on some vehicle derivatives to conform to
legal requirements. When under chassis
remove and refit procedures are required, it may
be necessary to remove the undertray
See
CHASSIS AND BODY, Repair, Front undertray
or
See CHASSIS AND BODY, Repair, Rear undertray
.
1.Install vehicle on a ramp.
2.Disconnect battery.
3.Remove gearbox carpet.
4.Remove gear lever and transfer box lever knobs.
5.Remove gear lever cover.
6.Remove nut and washer securing gear lever.
7.Mark gear lever spline setting and remove lever
and gaiter from the splined lower gear lever.
8.Release insulation pad from tunnel cover and
gear levers and remove.
9.Select low range on transfer box lever to prevent
lever from fouling tunnel when removing
gearbox.

37MANUAL GEARBOX
2
REPAIR
10.Remove 3 trim studs and lift up handbrake
gaiter.
11.Remove split pin, clevis pin, washer and
disconnect cable from handbrake lever. Ensure
handbrake is off.
12.Drain cooling system
See COOLING SYSTEM,
Adjustment, Drain and refill cooling system
.
13.Remove viscous fan unit
See COOLING
SYSTEM, Repair, Viscous coupling and fan
.
14.Slacken retaining clip and disconnect radiator
top hose at thermostat housing.
15.Slacken retaining clip and disconnect intake
hose at induction manifold. If EGR system is
fitted, slacken 2 retaining clips and disconnect
intake hose at intercooler.
16.Slacken retaining clip and disconnect hose at
turbocharger.
17.Remove bolt securing transmission breather
pipe clip to rear of engine.
18.Release breather pipes.
19.Release ties securing gearbox harness to
breather pipes.
20.Raise vehicle on ramp.
21.Position a suitable container under transmission
and drain main gearbox and transfer box
See
MAINTENANCE , Under vehicle maintenance
.
22.Mark front propeller shaft drive flange and
transfer box output flange for reassembly.
23.Remove 4 nuts and disconnect propeller shaft
from transfer box.

MANUAL GEARBOX
3
REPAIR
24.Remove 2 bolts, withdraw clutch slave cylinder
and backing plate from bell housing, and tie
aside.
25.Mark rear propeller shaft drive flange and
transmission brake drum for reassembly.
26.Remove 4 nuts, disconnect propeller shaft from
brake drum, and tie aside.
27.Remove front pipe from exhaust manifold
See
MANIFOLD AND EXHAUST SYSTEM, Repair,
Exhaust front pipe
.
28.Remove intermediate silencer.
See MANIFOLD
AND EXHAUST SYSTEM, Repair,
Intermediate pipe - 90
orSee MANIFOLD
AND EXHAUST SYSTEM, Repair,
Intermediate pipe - 110/130
29.Temporarily support transmission.
30.Remove nut securing gearbox LH mounting
rubber to chassis crossmember.
31.Remove 4 nuts and bolts securing crossmember
to chassis longitudinals.
32.Remove nut securing transfer box mounting
rubber to RH side of crossmember.
33.Remove 4 nuts and bolts securing crossmember
to chassis longitudinals.
34.With assistance and using a body jack between
chassis longitudinals, jack chassis sufficiently to
enable removal of crossmember.
35.Remove chasss crossmember.
36.Remove 4 bolts from both sides and remove LH
and RH mounting brackets.

37MANUAL GEARBOX
4
REPAIR
37.Pull handbrake cable through heel board and tie
aside.
38.Remove retaining nut, release clamp, and
disconnect speedometer cable from transfer box.
39.Release speedometer cable from retaining clip
on transfer box.
40.Remove retaining nut and release battery earth
strap from transfer box.
41.Secure manufactured cradleLRT-99-007to a
suitable hydraulic hoist.
42.Raise hoist and secure to gearbox with 3 bolts in
location provided.
43.Lower hoist sufficiently to allow transfer lever to
clear transmission tunnel aperture.
44.Disconnect differential lock switch and reverse
light connectors.
45.Remove bolt and release earth leads from RH
side of transfer box.
46.Support engine under sump with a jack.
47.Remove 14 bell housing to engine fixings.
48.Withdraw transmission whilst ensuring all
connections to engine and chassis are released.
49.Lower hoist and remove gearbox assembly.

MANUAL GEARBOX
5
REPAIR Separating transfer gearbox from main gearbox
50.Remove transmission assembly from hoist
cradle and position safely on a bench.
51.Remove breather pipes. Discard pipe union
sealing washers.
52.Remove 'Nyloc' nut, and remove bolt, securing
lever to high/low shaft.
53.Collect spacer washer.
54.Remove 2 clips and remove differential lock
lever link.
55.Remove lower locknut from high/low operating
rod.
56.Place a sling round transfer box and attach to
hoist.
57.Remove nut and 4 bolts securing transfer
gearbox to extension housing.
58.Withdraw transfer gearbox.
Assembling transfer gearbox to main gearbox
59.Clean extension housing and transfer gearbox
mating faces.
60.Ensuring loose upper dowel is fitted, hoist
transfer gearbox into position.
61.Secure transfer box to extension housing.
Tighten fixings to
40 Nm (30 lbf/ft).
62.Connect high/low operating rod, fit and tighten
locknut.
63.Fit link to differential lock lever and secure with 2
clips
64.Align lever to high/low shaft, position washer, fit
bolt and new Nyloc nut. Tighten to
2 Nm (1.5
lbf/ft).
65.Position breather pipes, secure pipe unions
using new sealing washers. Tighten unions to
15
Nm (11 lbf/ft).
Fitting transfer gearbox and main gearbox
assembly
66.Position transmission assembly to hoist cradle.
67.Clean bell housing and engine mating faces.
Apply sealant to both mating faces.
68.Temporarily fit gear lever and select any gear in
main gearbox to facilitate entry of gearbox input
shaft. Engage low range.
69.Position and raise hoist, fit transmission to
engine whilst keeping harness and pipes clear to
prevent trapping.
70.Secure transmission to engine. Tighten fixings to
45 Nm (33 lbf/ft).
71.Secure earth leads to RH side of transfer box.
72.Connect reverse lamp switch connectors and
differential lock switch connectors.
73.Secure breather pipes to harness with clips.
74.Remove support from engine sump.
75.Position temporary support under transmission.
76.Secure LH and RH mounting brackets to
gearbox. Tighten fixings to
55 Nm (41 lbf/ft).
77.With assistance and using a body jack between
chassis longitudinals, jack chassis sufficiently to
enable fitment of crossmember.

37MANUAL GEARBOX
6
REPAIRREV: 05/99 78.Position crossmember and locate over fixing
studs of LH and RH gearbox mounting rubbers.
79.Align crossmember and secure to chassis with 4
nuts and bolts on each side.
NOTE: Fit battery earth strap retaining clip
to LH top bolt.
80.Fit intermediate silencer.
See MANIFOLD AND
EXHAUST SYSTEM, Repair, Intermediate
pipe - 90
orSee MANIFOLD AND EXHAUST
SYSTEM, Repair, Intermediate pipe - 110/130
.
81.Fit front pipe to exhaust manifold
See
MANIFOLD AND EXHAUST SYSTEM, Repair,
Exhaust front pipe
.
82.Fit rear propeller shaft to transmission brake
drum. Tighten nuts to
47 Nm (33 lbf/ft).
83.Remove 3 bolts securing support cradle to
transmission and remove hoist.
84.Reconnect battery earth strap to transfer box
fixing.
85.Connect speedometer cable to transfer box and
secure with retaining clip.
86.Coat both sides of clutch slave clinder backing
plate with Hylomar P232M waterproof sealant.
87.Locate backing plate on slave cylinder.
88.Fit slave cylinder to bell housing, engaging
push-rod through centre of dust cover, and with
bleed screw uppermost. Tighten bolts to
25 Nm
(18 lbf/ft).
89.Fit front propeller shaft to transfer box. Tighten
nuts to
47 Nm (33 lbf/ft).
90.Refill main gearbox and transfer boxSee
MAINTENANCE , Under vehicle maintenance
.
91.Feed transmission brake cable through heel
board and ensure grommet is correctly located.
NOTE: Apply a soap solution to aid fitment
of cable.
92.Lower vehicle on ramp.
93.Fit ties to secure gearbox harness to
transmission breather pipes.
94.Fit breather pipe retaining clip to rear of engine.
95.Reconnect charge air hose at turbocharger.
96.Reconnect intake hose at induction manifold. If
EGR system is fitted, reconnect intake hose at
intercooler.
97.Reconnect radiator top hose at thermostat
housing.
98.Fit viscous fan unit
See COOLING SYSTEM,
Repair, Viscous coupling and fan
.
99.Reconnect battery.100.Refill cooling system
See COOLING SYSTEM,
Adjustment, Drain and refill cooling system
.
101.Connect cable clevis to handbrake lever and fit
handbrake gaiter.
102.Locate insulation pad over gear levers and fit to
tunnel cover.
103.Fit gear lever with gaiter to lower lever spline
and secure with retaining nut.
104.Fit gear lever cover.
105.Fit gear lever and transfer box lever knobs.
106.Fit gearbox cover carpet.
107.Check operation of handbrake and adjust as
necessary
See MAINTENANCE , Under
vehicle maintenance
.

MANUAL GEARBOX
1
SPECIFICATIONS, TORQUE REV: 05/99 TORQUE VALUES
NOTE: Torque wrenches should be regularly checked for accuracy to ensure that all fixings are
tightened to the correct torque.
Nm
Slave cylinder to bell housing 25....................................................................
Breather 15.....................................................................................................
Bell housing to cylinder block 40.....................................................................
High/low level to shaft 2.................................................................................
Transfer box to gearbox 45.............................................................................
NOTE: Torque values below apply to all screws and bolts used unless otherwise specified.
METRIC Nm
M5 6......................................................................................................
M6 9......................................................................................................
M8 25.....................................................................................................
M10 45...................................................................................................
M12 90...................................................................................................
M14 105..................................................................................................
M16 180..................................................................................................
UNC / UNF
1/4 9......................................................................................................
5/16 24...................................................................................................
3/8 39.....................................................................................................
7/16 78...................................................................................................
1/2 90.....................................................................................................
5/8 136....................................................................................................