seat adjustment LAND ROVER DEFENDER 1996 Workshop Manual

INTRODUCTION
13
INFORMATION FAULT DIAGNOSTIC EQUIPMENT
TESTBOOK
For Defender models fitted with the vehicle Anti-theft
Immobilisation and Alarm System, diagnostic
equipment, named TestBook, is available to assist in
the diagnostic and fault finding abilities of the Dealer
workshop. A diagnostic connector, located under the
front centre seat, or cubby box, as shown below, is
provided to facilitate the procedures.
If an exhaust gas recirculation (EGR) system is fitted,
this too can be checked using TestBook. A diagnostic
connector, also located under the front centre seat or
cubby box, is provided.
Features of Testbook include :-
Fully upgradable support for the technician.
Structured diagnostics to accommodate all skill levels.
Touch screen operation.
Direct print out of screen information and test results.READING THIS MANUAL
This manual is divided into sections shown on the
contents page, alongside a range of icons, familiar to
service technicians.
Relevant information is contained within each of these
sections. These are further divided into the following
sub-sections which appear at the foot of each page :-
Description and operation.
Fault diagnosis.
Adjustment.
Repair.
Overhaul.
Specifications, Torque.
To avoid repeating information through the sections,
where part of the repair operation impacts on another
section, a cross reference is given to direct the reader
to where the information is sited.
For example:
The maintenance section states the need to renew
drive belt. A cross reference sites this information in:
Section 12 Engine
- Sub-section: Repairs
- Heading: Drive belt renew.

MAINTENANCE
1
MAINTENANCE SERVICE SCHEDULE
The following section describes the items detailed in
the vehicle Service Schedule. Where required
instructions are given for carrying out the service
procedure, or a cross reference is given to the section
in the manual where the procedure may be found.
Service Maintenance Schedules are published
separately to reflect the needs and intervals for each
vehicle variant. Procedures in the Workshop Manual
must be used in conjunction with the Service
Schedule sheets.
Service Maintenance Schedules are available from:
Land Rover Publications,
Character Mailing,
Heysham Road,
Bootle,
Merseyside, L70 1JL
VEHICLE INTERIOR
CHECK SEATS & BELTS
Check condition and security of seat belts, seat belt
mountings, seat belt buckles and operation of inertia
seat belts.
CHECK OPERATION OF LAMPS
Check operation of all lamps, horns and warning
indicators.
CHECK OPERATION OF WIPERS
Check operation of front/rear wipers and washers and
condition of wiper blades.CHECK OPERATION OF HANDBRAKE
Handbrake check/adjust
1.Chock road wheels.
2.Raise one rear wheel clear of ground and
support securely with axle stand.
3.Release handbrake lever.
4.Underneath vehicle, tighten adjuster bolt
clockwise to
25 Nm (18 lbf/ft)to fully lock brake
drum.
5.Slacken adjusting bolt by 1.5 turns to give brake
shoes running clearance. Check that the drum is
free to rotate.
6.Adjust handbrake cable locknuts to give pawl
two notches free movement on the rachet before
being fully operational on third notch of rachet.
NOTE: Cable adjustment must ONLY be
used for initial setting and to compensate
for cable stretch. It MUST NOT be used to
take up brake shoe wear, which MUST be adjusted
at brake drum.
7.Operate handbrake to settle brake shoes.
Recheck handbrake is fully operational on third
notch of rachet pawl. Readjust if necessary.
8.Remove axle stand and wheel chocks.

MAINTENANCE
13
MAINTENANCE REV: 05/992.When pure diesel is emitted, retighten drain
plug.
3.Disconnect fuel inlet pipe at sedimenter. Raise
and support pipe above level of fuel tank to
prevent fuel draining from tank.
4.Support sedimenter bowl, unscrew bolt and
remove bowl.
5.Remove sedimenter element.
6.Clean all components in kerosene.
7.Fit new seals.
8.Fit element into sedimenter bowl.
9.Secure bowl to sedimenter head.
10.Fit fuel inlet pipe to sedimenter.
11.Slacken drain plug and when pure diesel is
emitted, retighten plug.
12.If necessary, prime the system.
See FUEL SYSTEM, Adjustment, Priming
the fuel system
CHECK CONDITION OF ENGINE MOUNTING
RUBBERS
CHECK SECURITY OF TOWING BRACKET
FITTINGSCARRY OUT ROAD OR ROLLER TEST
WARNING: Two wheel roller tests MUST
NOT be carried out.
For details of dynamometer testing.
See
INTRODUCTION, Information, Dynamometer
testing
Check the following components:
1.Engine for excessive noise.
2.Clutch for slip, judder or spin/drag.
3.Gear selection/noise - high/low range.
4.Steering for abnormal noise/effort.
5.Steering for free play.
6.All instruments, gauges and warning indicators.
7.Heater and air conditioning systems.
8.Heated rear screen.
9.Shock absorbers - ride irregularities.
10.Foot brake, on emergency stop, pulling to one
side, binding and pedal effort.
11.Handbrake operation.
12.Seat reclining and latching.
13.Fully extend seat belt, check operation of
retraction and latching. Inertia belts lock when
snatched or vehicle on slope.
14.Road wheel balance.
15.Transmissions for vibrations.
16.Body noises, squeaks and rattles.
17.Excessive exhaust smoke.
18.Engine idle speed.
19.Endorse service record.
20.Report any unusual features of vehicle condition
and additional work required.
ENDORSE SERVICE RECORD

ENGINE
1
ADJUSTMENT REV: 05/99 VALVE CLEARANCES - CHECK AND ADJUST
Service repair no - 12.29.48
Adjust
CAUTION: If the crankshaft is rotated with
excessive valve clearace, it is possible
that the push rods could be dislodged
from the cam follower seating and fracture the
cam follower slide. To prevent damage, eliminate
all clearance from any loose rockers before
turning the crankshaft to adjust clearances.
1.Rotate crankshaft until No.8 valve (counting from
front of engine) is fully open.
2.Using a 0,20 mm (0.008 in) feeler gauge adjust
clearance of No.1 valve.
3.Slacken locknut and turn adjusting screw
clockwise to reduce clearance and
anti-clockwise to increase clearance. Tighten
locknut to
16 Nm.
4.Repeat operation for remaining tappets in the
following sequence:
No.3 tappet with No.6 valve fully open.
No.5 tappet with No.4 valve fully open.
No.2 tappet with No.7 valve fully open.
No.8 tappet with No.1 valve fully open.
No.6 tappet with No.3 valve fully open.
No.4 tappet with No.5 valve fully open.
No.7 tappet with No.2 valve fully open.
5.On completion, recheck clearances and adjust
as necessary.

ENGINE
23
REPAIR
43.Check and adjust valve clearances.
See Adjustment, Valve clearances - check
and adjust
44.Fit rocker cover, ensuring oil seal is satisfactory
for continued use, and renew if necessary.
45.Secure rocker cover with special seal washers
and nuts. Tighten to
10 Nm (7 lbf/ft).
46.Fit rear engine lifting bracket, securing breather
pipe and multi-plug retaining clips. Tighten fixing
bolts to
25 Nm (18 lbf/ft).
47.Fit engine harness bracket to cylinder head.
48.Secure air cleaner mounting bracket to support
strut.
49.Connect heater hose to rear of cylinder head.
50.Position heater rail and connect hose from water
pump.
51.Fit exhaust manifold and turbocharger assembly.
See MANIFOLD AND EXHAUST SYSTEM,
Repair, Exhaust manifold
52.Fit induction manifold.See MANIFOLD AND
EXHAUST SYSTEM, Repair, Induction
manifold
53.Connect water temperature sensor lead.
54.Connect water pump hose at thermostat.
55.Fit bleed hose at thermostat.
56.Connect radiator top hose at thermostat.
57.Fit heater plugs.
See FUEL SYSTEM, Repair,
Heater plugs
58.Fit fuel injectors.See FUEL SYSTEM, Repair,
Fuel injectors
59.Fit crankcase ventilation valve and side breather
hose.
60.Fit air cleaner.
See FUEL SYSTEM, Repair,
Air cleaner
61.Refill cooling system.See COOLING SYSTEM,
Repair, Drain and refill cooling system
62.Fit bonnet.
63.Reconnect battery.OIL PUMP
Service repair no - 12.60.26
Remove
1.Remove engine front cover.
See Front cover
gasket
2.Remove 7 screws and release oil pump retaining
plate from engine front cover.
3.Mark oil pump inner gear rotor, outer gear rotor
and front cover housing for reassembly.
4.Check for rotor clearances:
Outer rotor to housing, 0,025 - 0,075 mm (0.010
- 0.030 in).
Inner rotor to outer rotor, 0,025 - 0,075 mm
(0.010 - 0.030 in).
Rotor end float, 0,026 - 0,135 mm (0.010 - 0.054
in).
5.Remove inner and outer rotors.
6.Check condition of oil pump components.
NOTE: If the oil pump seating in the front
cover or retaining plate is badly worn,
pitted or scored, a new front cover must
be fitted.
See Front cover gasket
Always renew oil pump rotors as a pair.
7.Clean sealant from pump retaining plate and
front cover.

FUEL SYSTEM
7
REPAIR REV: 05/99
13.Remove single bolt fixing assembly securing
front of tank to chassis mounted bracket.
14.Remove 3 bolts securing tank mounting bracket
to chassis and release bracket.
15.Lower front of tank while turning anti-clockwise
and remove from vehicle.
16.If required, remove tank gauge unit.
See
INSTRUMENTS, Repair, Fuel gauge tank unit
- side fuel tank
orSee INSTRUMENTS,
Repair, Fuel gauge tank unit - rear fuel tank,
110/130
Refit
17.Fit filler hose and clip to tank but do not fully
tighten. Position clip screw so that it is
accessible when tank is fitted.
18.Fit breather hose and secure with clip.
19.Position fuel tank in vehicle and loosely secure
front mounting bracket to tank with special bolt
and rubber bushes.
20.Secure mounting bracket to chassis with 3 bolts
and fully tighten to
20 Nm (15 lbf/ft).
21.Secure rear of tank to chassis mounting and
tighten captive bolt plate fixings to
20 Nm (15
lbf/ft).
22.Fully tighten front fixing bolt assembly to20 Nm
(15 lbf/ft).
23.Fit spill return and fuel supply pipes and secure
union connections.
24.Fit fuel level unit electrical plug.
25.Fit hose to filler tube and tighten upper and lower
clips.
26.Check that drain plug is secure and fill fuel tank.
27.Reconnect battery.
28.Prime fuel system
See Adjustment, Priming
the fuel system
and start engine.
29.Check system for leaks and operation of fuel
gauge.
30.Fit seat base cover and seat cushion.SIDE MOUNTED FUEL TANK - 5 DOOR VEHICLES
Service repair no - 19.55.01
NOTE: This fuel tank is used on 110/130 5
door vehicles fitted with a twin tank
option.
WARNING: Before any attempt is made to
start the removal procedure it is vital that
the FUEL HANDLING PRECAUTIONS,
See
INTRODUCTION, Information, Fuel handling
precautions
are carefully studied and
implemented in the interests of safety.
Remove
1.Disconnect battery.
2.Remove tank drain plug, allow fuel to drain into a
clean container, and refit plug.
3.Remove RH seat cushion.
4.Remove retaining catch and remove seat base
cover to gain access to fuel tank.
5.Disconnect electrical plug from fuel gauge unit.
6.Disconnect fuel supply pipe from tank.
7.Disconnect spill return pipe from tank.
8.Remove 3 bolts securing tank to front mounting
bracket.
9.Support front of tank and remove single fixing
assembly securing tank to rear mounting
bracket.
10.Remove tank from vehicle.
11.If required, remove fuel gauge unit.
See
INSTRUMENTS, Repair, Fuel gauge tank unit
- side fuel tank
orSee INSTRUMENTS,
Repair, Fuel gauge tank unit - rear fuel tank,
110/130
Refit
12.Position fuel tank in vehicle and loosely secure
to rear mounting bracket with special bolt and
rubber bushes.
13.Secure tank to front mounting bracket and
tighten fixings to
20 Nm (15 lbf/ft).
14.Fully tighten rear fixing bolt assembly to20 Nm
(15 lbf/ft).
15.Fit spill return and fuel supply pipes to fuel tank
and securely tighten union connectios.
16.Fit electrical plug to fuel gauge unit.
17.Check that drain plug is secure and fill fuel tank.
18.Reconnect battery.
19.Prime fuel system.
See Adjustment, Priming
the fuel system
and start engine.
20.Check system for leaks and operation of fuel
gauge.
21.Fit seat base cover and seat cushion.

19FUEL SYSTEM
10
REPAIR TWIN TANK CHANGE-OVER TAP ASSEMBLY
Service repair no - 19.43.50 - Fuel supply tap
Service repair no - 19.43.51 - Spill return tap
Service repair no - 19.43.52 - Fuel tank
change-over lever
Remove
1.Disconnect battery.
2.Remove RH front seat cushion.
3.Release retaining clip and remove access cover
from seat base.
4.Disconnect leads from fuel tank change-over
switch.
5.Unscrew retaining nut and withdraw change-over
lever and washers from pivot pin at heelboard.
6.Disconnect spill return pipes at spill change-over
tap.
7.Remove 4 bolts, washers and nuts securing tap
support bracket assembly to heel board.
8.Lift up support bracket assembly and disconnect
control rod from spill tap lever.
9.Remove support bracket assembly from vehicle.
10.Disconnect fuel supply pipes at fuel change-over
tap.
11.Remove 2 screws and release fuel tap from
chassis mounted support bracket.12.Remove fuel tap, complete with operating rod
and lever.
13.Plug all connections to prevent ingress of dirt.
14.Dismantle spill return and fuel tap components
as necessary.
Refit
15.Fit fuel change-over tap, complete with operating
rod and lever, to chassis mounted support
bracket and fully tighten fixing screws.
16.Connect fuel supply pipes at fuel tap, ensuring
they are fitted to correct ports.
17.Position support bracket assembly behind
heelboard and connect operating rod to spill
change-over tap lever.
18.With pivot pin bush correctly seated, secure
support bracket assembly to heel board and
tighten fixings to
8 Nm (6 lbf/ft).
19.Connect spill return pipes to change-over tap,
ensuring they are fitted to correct ports.
20.Secure change-over lever to pivot pin.
21.Fit leads to fuel tank change-over switch.
22.Reconnect battery.
23.Prime vehicle fuel system,
See Adjustment,
Priming the fuel system
if necessary and
check for leaks.
24.Fit access cover to seat base and seat cushion.

19FUEL SYSTEM
18
REPAIR EGR THROTTLE POSITION SENSOR
Service repair no - 17.45.08
Remove
1.Remove 2 screws securing throttle position
sensor mounting plate to injection pump.
2.Disconnect sensor multi-plug.
3.Remove sensor assembly.
Refit
4.Position sensor assembly on injection pump and
secure with screws.
5.Connect multi-plug.
6.Adjust sensor
See Adjustment, EGR throttle
sensor
EGR CONTROL UNIT
Service repair no - 17.45.07
Remove
1.Raise centre seat, or cubby box
See CHASSIS
AND BODY, Repair, Cubby box
to gain access
to EGR control unit harness.
2.Disconnect control unit multi-plug and remove
centre seat or cubby box.
3.Remove 4 screws and detach control unit from
seat or cubby box base.
Refit
4.Secure EGR control unit to base of centre seat
or cubby box.
5.Position centre seat or cubby box and connect
control unit multi-plug.
6.Fit centre seat, or cubby box.
See CHASSIS
AND BODY, Repair, Cubby box

REAR AXLE AND FINAL DRIVE
5
OVERHAUL
55.Position a suitable dial gauge indicator on casing
with stylus registering on back face of crown
wheel.
56.Rotate differential and check total indicated
run-out on crown wheel back face. This must not
exceed 0,05 mm. If run-out is excessive, check
mating faces for dirt and damage; if necessary,
select a new radial position for crown wheel.
When satisfactory, continue with following check.
Differential bearing adjustment
57.Insert two levers between casing and differential
unit at one side.
58.Move differential unit fully to one side of casing;
do not tilt unit.
59.Rotate differential unit to settle bearings,
continue to lever differential to side, then zero
dial gauge indicator.
60.Lever assembly fully to other side of casing,
rotate unit to settle bearings, then note total
indicator reading.
61.Add 0,127 mm, for bearing pre-load, to total
noted in preceding instruction. The sum is then
equal to nominal value of shims required for
differential bearings. Shims are available in
range 0,07 mm, 0,12 mm, 0,25 mm and 0,76
mm. Select total value of shims required.
62.Remove differential unit and bearings and place
aside. Do not fit shim washers until subsequent
'Differential backlash' checks have been made,
instructions 96 to 102.Fit drive pinion
63.Select shim washers of same thickness value as
those removed from under pinion inner cup,
instruction 35, and place ready for fitting.
64.Position outer bearing replacerLRT-51-505,
detail 2, and outer bearing cup on press
LRT-99-502.
65.Locate assembly into pinion housing nose.
66.Place selected shim washers on to inner bearing
cup seating.
67.Position inner bearing cup in casing.
68.Position inner bearing replacerLRT-51-505,
detail 1, ontoLRT-99-502and secure with fixing
nut.
69.Hold still centre screw and turn butterfly lever to
draw in bearing cups.

REAR AXLE AND FINAL DRIVE
9
OVERHAUL Differential backlash checks
96.Pick up differential unit as left after instruction
52.
97.Fit differential unit and lever unit away from drive
pinion until opposite bearing cup is seated
against housing. Do not tilt unit.
98.Install a dial gauge on casing with its stylus
resting on back face of crown wheel. Zero the
gauge.
99.Lever differential unit to engage crown wheel
teeth in full mesh with drive pinion teeth. Do not
tilt unit.
100.Note total reading obtained on dial gauge.
101.From this figure subtract 0,25 mm to obtain
correct crown wheel backlash when fitted. The
result indicates value of shimming to be fitted
between differential case and bearing cone at
crown wheel side of differential.
102.Fit shim value determined in instruction 101,
taking shims from pack previously determined
during 'Differential bearing adjustment' checks,
instructions 57 to 62LRT-51-500details 1 and 2,
pressLRT-99-002, andLRT-51-504.
103.Fit remaining shims from instruction 101 to
opposite side of differential.LRT-51-501details
1 and 2, pressLRT-99-002, andLRT-51-504.
104.Fit differential unit with shims and bearings to
axle casing, using axle spreaderLRT-51-503
with pegs18G131F.
105.Remove axle spreader.106.Fit bearing caps in their correct position,
referring to relationship markings on caps and on
axle casing.
107.Tighten bearing caps fixings to
135 Nm (100
lbf/ft).
108.Mount a dial gauge on axle casing with stylus
resting on a crown wheel tooth.
109.Prevent drive pinion from rotating and check
crown wheel backlash which must be 0,15 to
0,27 mm. If backlash is not within specified
limits, repeat differential backlash checks,
instructions 96 to 102 looking for possible errors.
110.Fit differential cover and new gasket, coating
both sides of gasket with Hylomar PL 32M or an
equivalent non-setting sealant. Torque load for
fixings is
30 Nm (22 lbf/ft).
111.Reverse instructions 3 to 5 and coat threads of
hub driving member bolts with Loctite 'Studlock'
grade CVX and fit and tighten bolts evenly to
correct torque.
112.Fit rear axle assembly to vehicle
See Repair,
Rear axle
.
113.Replenish differential with recommended
lubricant
See LUBRICANTS, FLUIDS AND
CAPACITIES, Information, Recommended
lubricants and fluids
. After initial axle run,
check oil level and replenish as necessary to
filler/level plug hole.
114.Where major running parts have been replaced
during servicing, it is a recommended practice to
allow axle assembly to 'run in' by avoiding,
where possible, heavy loads and high speeds
during initial running.