fuel pump LAND ROVER DEFENDER 1996 Service Manual

86ELECTRICAL
4
DESCRIPTION AND OPERATION REV: 05/99 ALARM SYSTEM COMPONENT LOCATION
COMPONENT LOCATION
1. Electronic control unit (ECU) Under dash, LH and RH drive
2. Anti-theft alarm indicator light Instrument panel
3. Engine immobilisation warning light Instrument panel
4. Immobilisation spider* Inside vehicle battery box
5. Passive coil Over starter switch barrel
6. Bonnet switch Engine compartment, LH and RH drive
7. Door switches
8. Ultrasonic sensor Varies according to vehicle type
9. Handset and key
10. Alarm sounder (without battery back-up) LH inner front wing
11. Alarm sounder (with battery back-up) LH inner front wing
* Replaced in some markets by a digital diesel shut-off valve (DDS), secured directly to fuel shut-off solenoid on
injection pump.

ELECTRICAL
9
DESCRIPTION AND OPERATION IMMOBILISATION AND ALARM SYSTEM CIRCUIT
DIAGRAM
1.Anti-theft alarm indicator light (LED)
2.Engine immobilisation warning light
3.Alarm system fuse - 15 amp
4.Alarm sounder relay
5.Under bonnet lighting fuse
6.Alarm sounder (without battery back-up)
7.Alarm system fuse - 5 amp (position 20)
8.Electronic control unit (ECU)
9.Bonnet switch
10.Alarm sounder protection fuse - 20 amp
(position 10)
11.Starter switch
12.Under bonnet ignition fuse
13.Driver's door switch
14.Vehicle horn switch
15.Vehicle horn
16.Passive coil
17.Starter switch relay
18.Front passenger door switch
19.Hazard warning light fuse - 15 amp (position 1)
20.Ultrasonic sensor
21.Interior lamp and horn fuse - 20 amp (position 3)
22.Alarm sounder (with battery back-up)
23.LH direction indicator lamps
24.RH direction indicator lamps
25.Interior lamp
26.Immobilisation spider
27.Rear side doors and rear door switches
28.Diagnostic connector
29.Diagnostic fuse - 7.5 amp
30.Starter solenoid
31.Fuel switch-off solenoid (injection pump)
32.Generator
33.AerialKey to cable colours
B-Black
G-Green
K-Pink
LG-Light Green
N-Brown
O-Orange
P-Purple
R-Red
S-Slate
U-Blue
W-White
Y-Yellow
The last letter of a colour code denotes the tracer
colour

ELECTRICAL
11
DESCRIPTION AND OPERATION IMMOBILISATION AND ALARM SYSTEM CIRCUIT
DIAGRAM - WITH DDS
1.Anti-theft alarm indicator light (LED)
2.Engine immobilisation warning light
3.Alarm system fuse - 15 amp
4.Alarm sounder relay
5.Under bonnet lighting fuse
6.Alarm sounder (without battery back-up)
7.Alarm system fuse - 5 amp (position 20)
8.Electronic control unit (ECU)
9.Bonnet switch
10.Alarm sounder protection fuse - 20 amp
(position 10)
11.Starter switch
12.Under bonnet ignition fuse
13.Driver's door switch
14.Vehicle horn switch
15.Vehicle horn
16.Passive coil
17.Starter switch relay
18.Front passenger door switch
19.Hazard warning light fuse - 15 amp (position 1)
20.Ultrasonic sensor
21.Interior lamp and horn fuse - 20 amp (position 3)
22.Alarm sounder (with battery back-up)
23.LH direction indicator lamps
24.RH direction indicator lamps
25.Interior lamp
26.Digital diesel shut-off valve (DDS)
27.Rear side doors and rear door switches
28.Diagnostic connector
29.Diagnostic fuse - 7.5 amp
30.Starter solenoid
31.Fuel shut-off solenoid (injection pump)
32.Generator
33.AerialKey to cable colours
B-Black
G-Green
K-Pink
LG-Light Green
N-Brown
O-Orange
P-Purple
R-Red
S-Slate
U-Blue
W-White
Y-Yellow
The last letter of a colour code denotes the tracer
colour

ELECTRICAL
25
REPAIR DIGITAL DIESEL SHUT-OFF VALVE (DDS)
Service repair no - 86.77.00
Remove
1.Remove fuel injection pump
See FUEL
SYSTEM, Repair, Fuel injection pump.
2.Drill out 2 shear bolts securing DDS valve and
clamp, using a 3.2 mm drill, to a depth of
approximately 5 mm.
CAUTION: Use a drill bushing to guide the
drill.
3.Using an extractor, remove the 2 DDS valve
retaining bolts and discard.
4.Release DDS valve from fuel shut-off solenoid.
5.Remove protective cap from shut-off solenoid.
6.Unscrew terminal nut, release terminal lead
eyelet and remove DDS valve.7.Remove protective cap retainer and release
DDS valve clamp from behind fuel shut-off
solenoid.
Refit
8.Position DDS valve clamp behind fuel shut-off
solenoid and fit protective cap retainer.
9.Fit DDS terminal lead to fuel shut-off solenoid.
Tighten nut to
2 Nm (1.5 lbf/ft).
10.Fit protective cap to fuel shut-off solenoid,
ensuring terminal lead is correcly routed on RH
side of cap.
11.Secure DDS valve to fuel cut-off solenoid and
clamp. Tighten new shear bolts progressively
until heads shear.
12.Fit fuel injection pump
See FUEL SYSTEM,
Repair, Fuel injection pump.