wheel LAND ROVER DEFENDER 1996 Repair Manual

REAR AXLE AND FINAL DRIVE
9
OVERHAUL Differential backlash checks
96.Pick up differential unit as left after instruction
52.
97.Fit differential unit and lever unit away from drive
pinion until opposite bearing cup is seated
against housing. Do not tilt unit.
98.Install a dial gauge on casing with its stylus
resting on back face of crown wheel. Zero the
gauge.
99.Lever differential unit to engage crown wheel
teeth in full mesh with drive pinion teeth. Do not
tilt unit.
100.Note total reading obtained on dial gauge.
101.From this figure subtract 0,25 mm to obtain
correct crown wheel backlash when fitted. The
result indicates value of shimming to be fitted
between differential case and bearing cone at
crown wheel side of differential.
102.Fit shim value determined in instruction 101,
taking shims from pack previously determined
during 'Differential bearing adjustment' checks,
instructions 57 to 62LRT-51-500details 1 and 2,
pressLRT-99-002, andLRT-51-504.
103.Fit remaining shims from instruction 101 to
opposite side of differential.LRT-51-501details
1 and 2, pressLRT-99-002, andLRT-51-504.
104.Fit differential unit with shims and bearings to
axle casing, using axle spreaderLRT-51-503
with pegs18G131F.
105.Remove axle spreader.106.Fit bearing caps in their correct position,
referring to relationship markings on caps and on
axle casing.
107.Tighten bearing caps fixings to
135 Nm (100
lbf/ft).
108.Mount a dial gauge on axle casing with stylus
resting on a crown wheel tooth.
109.Prevent drive pinion from rotating and check
crown wheel backlash which must be 0,15 to
0,27 mm. If backlash is not within specified
limits, repeat differential backlash checks,
instructions 96 to 102 looking for possible errors.
110.Fit differential cover and new gasket, coating
both sides of gasket with Hylomar PL 32M or an
equivalent non-setting sealant. Torque load for
fixings is
30 Nm (22 lbf/ft).
111.Reverse instructions 3 to 5 and coat threads of
hub driving member bolts with Loctite 'Studlock'
grade CVX and fit and tighten bolts evenly to
correct torque.
112.Fit rear axle assembly to vehicle
See Repair,
Rear axle
.
113.Replenish differential with recommended
lubricant
See LUBRICANTS, FLUIDS AND
CAPACITIES, Information, Recommended
lubricants and fluids
. After initial axle run,
check oil level and replenish as necessary to
filler/level plug hole.
114.Where major running parts have been replaced
during servicing, it is a recommended practice to
allow axle assembly to 'run in' by avoiding,
where possible, heavy loads and high speeds
during initial running.

51REAR AXLE AND FINAL DRIVE
10
OVERHAUL REAR HUB ASSEMBLY - 90
Service repair no - 64.15.13.
1.Remove rear hub
See Repair, Rear hub
assembly
.
2.Remove outer bearing.
3.Mark, for reassembly, position of hub to brake
disc.4.Remove 5 bolts and separate hub from brake
disc.
WARNING: A maximum of two road wheel
retaining studs can be renewed. Should
more studs be unserviceable fit new hub
with studs.
5.Remove grease seal and inner bearing from
hub.
6.Remove inner and outer bearing tracks.
REAR HUB COMPONENTS - 90
1.Axle shaft.
2.Axle shaft joint washer.
3.Axle shaft retaining bolt.
4.Lock nut.
5.Lock washer.
6.Hub adjusting nut.
7.Spacing washer.8.Outer bearing.
9.Hub.
10.Inner bearing.
11.Grease seal.
12.Brake disc.
13.Disc retaining bolt.

REAR AXLE AND FINAL DRIVE
1
SPECIFICATIONS, TORQUE REV: 05/99 TORQUE VALUES
NOTE: Torque wrenches should be regularly checked for accuracy to ensure that all fixings are
tightened to the correct torque.
Nm
REAR AXLE
Pinion housing to axle case 41.......................................................................
Crown wheel to differential case 58................................................................
Differential bearing cap to pinion housing 90..................................................
Differential drive flange to drive shaft 47.........................................................
Bevel pinion nut 129........................................................................................
Lower link to axle 176......................................................................................
Pivot bracket ball joint to axle 176...................................................................

FRONT AXLE AND FINAL DRIVE
1
DESCRIPTION AND OPERATION DESCRIPTION
The welded steel front axle casing houses a separate
spiral bevel type differential unit, which is off-set to the
right of the vehicle centre line. The differential unit
drives the front wheels via the axle shafts and
constant velocity joints which are totally enclosed in
the spherical and swivel housings.The front wheels are pivoted on tape roller bearings at
the top and bottom of the swivel housing. The wheel
hubs on all axles are supported by two taper bearings
and driven by drive flanges which are splined to the
one piece, stub shaft/constant velocity joint.
Front axle hub and swivel housing
1.Axle casing
2.Ventilation pipe
3.Axle shaft
4.Wheel studs and hub
5.Stub axle
6.Wheel bearings
7.Inner and outer hub seals
8.Axle shaft seal
9.Hub lock plate, thrust washer and nuts
10.Brake disc
11.Drive flange
12.Shim washer and circlip13.Dust cap
14.Constant velocity joint/shaft
15.Thrust collar for CV joint
16.Roller bearing
17.Spacer
18.Circlip
19.Top and bottom swivel taper bearing
20.Top and bottom swivel pins
21.Spherical housing, seal and retainer
22.Swivel housing
23.Constant velocity shaft seal

54FRONT AXLE AND FINAL DRIVE
2
DESCRIPTION AND OPERATION Lubrication
The differential, swivel pin housing and wheel hubs
are indiviudally lubricated and separated by oil seals
(7) and (8), see J6267A, to prevent oil transfer across
the axle when the vehicle is traversing steep inclines.
The wheel bearings are lubricated with grease and the
swivel housing and differential with oil. On later
vehicles, identified by having only a filler plug in the
swivel housing, grease is used to lubricate the
housing assembly,
Ventilation
Ventilation of the differential is through a plastic pipe
(2) which terminates at a high level in the vehicle axle.
The swivel housings ventilate through axle shaft oil
seals (8) into the differential and the hub bearings
vent via the oil seals into the swivel housing.

FRONT AXLE AND FINAL DRIVE
1
REPAIR REV: 05/99 FRONT AXLE ASSEMBLY
Service repair no - 54.10.01
Remove
WARNING: Remove and refit of axle
requires a further two persons to steady
axle when lowering or repositioning axle.
1.Support chassis front.
2.Remove road wheels.
3.Support axle weight with hydraulic jack.
4.Remove radius arms to chassis frame nuts.
5.Disconnect steering damper from track rod.
Using a extractor remove track rod links from
swivel pin arms.
6.Remove four nuts and bolts securing radius
arms to axle bracket.
7.Remove radius arms.
8.Remove bolts securing brake hose brackets .
Refit bolts to prevent oil leakage.
9.Remove bolts from brake calipers and tie to one
side.
10.Remove nuts and washers securing shock
absorbers to axle.
11.Disconnect drag link from swivel pin housing
arm.
12.Remove two nuts and bolts securing panhard
rod to axle bracket. Lift rod clear of axle.
13.Mark for reassembly drive shaft flanges.
Remove four nuts and bolts, tie propeller shaft to
one side.
14.Release axle ventilation pipe banjo and lower
axle assembly. Remove road springs.
15.Disconnect anti-roll bar link
See FRONT
SUSPENSION, Repair, Anti-roll bar ball
.
16.Remove axle assembly.
Refit
17.Position axle under vehicle, supporting left side
of axle, and fit anti-roll bar links
See FRONT
SUSPENSION, Repair, Anti-roll bar links
.
18.Fit propeller shaft. Tighten bolts to
47 Nm (35
lbf/ft).
19.Fit panhard rod to axle bracket. Tighten bolts to
88 Nm (65 lbf/ft).
20.Fit drag link to swivel pin arm. Tighten fixings to
40 Nm (30 lbf/ft).
21.Fit shock absorbers to axle.
22.Fit brake calipers. Tighten bolts to
82 Nm (60
lbf/ft).
23.Tighten upper swivel pin bolts to78 Nm (58
lbf/ft).
24.Fit radius arms to axle brackets. Tighten bolts to
197 Nm (145 lbf/ft).
25.Fit steering damper to track rod.
26.Fit radius arms to chassis side member. Tighten
fixings to
197 Nm (145 lbf/ft).
27.Tighten track rod end to40 Nm (30 lbf/ft)and fit
new split pin.
28.Remove chassis supports, fit road wheels and
tighten to correct torque:
Alloy wheels -
130 Nm (96 lbf/ft)
Steel wheels -100 Nm (80 lbf/ft)
Heavy duty wheels -170 Nm (125 lbf/ft)

54FRONT AXLE AND FINAL DRIVE
2
REPAIR FRONT HUB ASSEMBLY
Service repair no - 60.25.01.
Remove
1.Loosen front wheel nuts, jack up vehicle and
lower onto axle stands and remove road wheel.
2.Release brake hose clips and remove brake
caliper and brake disc shield bolts. Secure to
one side.3.Lever off dust cap.
4.Remove circlip and drive shaft shim from
driveshaft.
5.Remove 5 bolts and withdraw driving member
and joint washer.
6.Bend back lock washer tabs.
7.Remove locknut and lock washer.
8.Remove hub adjusting nut.
9.Remove spacing washer.
10.Remove hub and brake disc assembly complete
with bearings.
HUB COMPONENTS
1.Dust cap.
2.Drive shaft circlip.
3.Drive shaft shim.
4.Drive member.
5.Drive member joint washer.
6.Drive member retaining bolt.
7.Lock nut.
8.Lock washer.9.Hub adjusting nut.
10.Spacing washer.
11.Outer bearing.
12.Hub.
13.Inner bearing.
14.Grease seal.
15.Brake disc
16.Disc retaining bolt.

FRONT AXLE AND FINAL DRIVE
3
REPAIR REV: 05/99 Refit
11.Clean stub axle and drive shaft and fit hub
assembly to axle.
12.Fit spacing washer.
13.Fit hub adjusting nut. Tighten to
50 Nm (37
lbf/ft).
Ensure hub is free to rotate with no
bearing play.
14.Back off adjusting nut 90°and tighten to
10 Nm
(7 lbf/ft).
15.Fit a new lock washer.
16.Fit locknut. Tighten to
50 Nm (37 lbf/ft).
17.Tab over lock washer to secure adjusting nut
and locknut.
18.Fit a new joint washer to driving member and fit
member to hub. Tighten bolts to
65 Nm (48
lbf/ft).
19.Fit original drive shaft shim and secure with a
circlip.
20.To check drive shaft end play, mount a dial
gauge using bracketLRT-99-503and rest pin in
a loaded condition on end of drive shaft.
21.Fit a suitable bolt to threaded end of drive shaft.
Move drive shaft in and out noting dial gauge
reading. End play should be between 0,08 to
0,25 mm.
22.If end play requires adjustment, remove circlip,
measure shim thickness and fit an appropriate
shim to give required end-play.
23.Remove bolt from drive shaft, fit circlip and dust
cap.
24.Fit brake disc shield and brake caliper. Tighten
fixings to
82 Nm (60 lbf/ft).
25.Bleed brake systemSee BRAKES, Repair,
Brake system bleed
.
26.Fit road wheel, remove axle stands and tighten
road wheel nuts to correct torque:
Alloy wheels -
130 Nm (96 lbf/ft)
Steel wheels -100 Nm (80 lbf/ft)
Heavy duty wheels -170 Nm (125 lbf/ft)
27.Operate footbrake to locate brake pads before
driving vehicle.

FRONT AXLE AND FINAL DRIVE
1
SPECIFICATIONS, TORQUE REV: 05/99 TORQUE VALUES
NOTE: Torque wrenches should be regularly checked for accuracy to ensure that all fixings are
tightened to the correct torque.
Nm
FRONT AXLE
Hub driving member to hub 65*.......................................................................
Brake disc to hub 73.......................................................................................
Stub axle to swivel pin housing 65*.................................................................
Brake caliper to swivel pin housing 82............................................................
Upper swivel pin to swivel pin housing 78*.....................................................
Lower swivel pin to swivel pin housing 78*.....................................................
Oil seal retainer to swivel pin housing 11........................................................
Swivel bearing housing to axle case 73*.........................................................
Pinion housing to axle case 41.......................................................................
Crown wheel to differential housing 58...........................................................
Differential bearing cap to pinion housing 90..................................................
Differential drive flange to drive shaft 47.........................................................
Mudshield to bracket lower swivel pin 11........................................................
Bevel pinion nut 130........................................................................................
Draglink to hub arm 40....................................................................................
Panhard rod to axle bracket 88.......................................................................
Radius arm to axle 190....................................................................................
Radius arm to chassis side member 190.........................................................
NOTE: * These bolts to be coated with Loctite 270 prior to assembly.

STEERING
1
DESCRIPTION AND OPERATION DESCRIPTION
The steering system incorporates a compression joint
in the lower shaft and is designed to collapse on
impact. The mis-alignment of the upper steering
column with the steering box and the inclusion of two
universal joints, is also designed to prevent the
column moving toward the driver under frontal impact.
The steering box is located behind the first chassis
cross member and is connected to the road wheel
swivel housing by a drag link and track rod. A
hydraulic damper absorbs shocks in the steering,
caused by road wheel deflections when operating on
rough terrain.Power steering system
The power steering system comprises a hydraulic
pump which is belt driven from the engine and
supplied with fluid from a reservoir that also acts as a
cooler.
The steering box houses a self neutralizing rotary
valve which is part of the worm/valve assy and an
hydraulic piston/rack to assist the mechanical
operation. The rotary valve which is operated by
movement of the steering wheel, directs fluid pressure
to the appropriate side of the hydraulic piston/rack to
provide assistance.
Power steering system
1.Hydraulic pump
2.Fluid reservoir
3.Steering box
4.Upper column5.Universal joints
6.Lower shaft
7.Compression joint
8.Drag link