wheel LAND ROVER DEFENDER 1996 Manual PDF

STEERING
11
FAULT DIAGNOSIS STIFF STEERING CHECKLIST
NOTE: Having completed visual checks
and steering assessment and confirmed
that vehicle steering load is incorrect carry
out the following procedure in order shown.
Steering wheel 'torque to turn' loads
1.Raise vehicle so both front wheels free.
2.With engine off, centralise steering wheel, and
remove steering wheel decal. Using torque
wrench on column nut, check torque required to
turn the steering wheel one turn in each
direction.
3.Record readings obtained in each direction.
Reading should be
4.40 Nm (3.5 lbf/ft).
NOTE: If figures are in excess of that
specified carry out steering box tie bar
reset below. If figures are as specified
See
Visual Check and Basic Adjustments
.
Steering box tie bar reset
1.Loosen the tie bar fixings one complete turn.
2.Drive vehicle carefully a short distance (within
the dealership) applying full lock in both
directions in order to settle steering components.
Drive vehicle over speed bumps and include
harsh braking if possible.
WARNING: Do not drive on public
highway.
3.Near end of operation 2. ensure vehicle is driven
in a straight line on level ground and halted.
4.Tighten panhard rod mounting arm nut to
110
Nm (81 lbf/ft).
5.Tighten the 2 fixings, tie bar to steering box, to
81 Nm (60 lbf/ft).
6.Recheck steering wheel torque to turn. If torque
reading is still greater than specified, carry out
steering shaft universal joint lubrication.Lower steering shaft universal joint lubrication
1.Check lower steering shaft is correctly phased
See Repair, Lower Steering Shaft and
Universal Joints
.
2.Lubricate universal joints with an anti-seizure
type penetrating spray. Work the joints to ensure
full penetration of the spray by driving vehicle
and steering from lock to lock.
3.If steering stiffness still persists carry out swivel
pin preload setting.
Swivel pin preload setting
1.The swivel pin preload setting must be checked
and set
See FRONT AXLE AND FINAL DRIVE,
Overhaul, Front Stub Axle, Constant Velocity
Joint and Swivel Pin Housing
.
Note that a pull load of 1.16 - 1.46 kg is required
after the axle shaft and swivel housing seal have
been removed.
Steering box adjustment
1.Check steering box adjustment
See
Adjustment, Power Steering Box
.
Steering damper check
1.Check condition of steering damper
See
Steering Damper
.

57STEERING
12
FAULT DIAGNOSISREV: 05/99 VISUAL CHECK AND BASIC ADJUSTMENTS
NOTE: It is important that the following
instructions are carried out in the
sequence shown and the results recorded.
1.Road springs - check that road springs are
correctly seated and are to correct specification
for vehicle. For spring specification
See
GENERAL SPECIFICATION DATA,
Information, Road Spring Data
.
2.Ride height - measure trim height from wheel
centre to wheelarch eyebrow. Record results on
data sheet.
3.Check/top up power steering fluid
See Repair,
Power Steering Fluid Reservoir
.
4.Check tension and condition of drive belt
See
ELECTRICAL, Repair, Auxiliary drive belt
.
5.Track rod/drag link - check condition of track rod,
drag link and ball joints
See Repair, Drag Link
and Drag Link Ends
.
If either component is damaged, check operation
of steering damper and steering box for
smoothness. Replace all damaged or worn
components that impair the operation of the
steering system.
6.Suspension bushes - examine all steering and
suspension bushes for signs of wear and
deterioration. Also check all fixings for torque
relaxation. Tighten to correct torque value
See
FRONT SUSPENSION, Specifications, torque,
Torque Values
.
7.Oil leaks - check front and rear axle hubs for
leak and repair as necessary.
8.Brake system - check brake system for leaks,
pipe condition, pad wear/contamination, disc
wear/condition.
9.Hub end float - check movement in the hubs by
rocking the wheels.
10.Check front wheel alignment. Vehicles displaying
a tendency to veer more than considered
allowable, it is permissible to set the front track
to parallel.11.Having completed all the above checks and
adjustments, road test vehicle
See Road Test
Procedure
.
Attempt to reproduce the symptoms established
earlier. If symptoms still exist refer to relevant
Diagnostic Chart.
STEERING LINKAGE INSPECT
NOTE: When inspecting steering linkages
and ball joints for wear the following items
must be checked.
Steering ball joints
1.Check ball joint rubber boots for security, signs
of cracking or deterioration.
2.Check ball joint assemblies for seizure i.e. no
movement on ball joint and associated
assemblies.
3.Check for excessive wear. This will be evident
as extreme movement on track rod and steering
linkages. Renew parts as necessary
See
Repair, Track Rod and Linkage
,See Repair,
Drag Link and Drag Link Ends
.
Steering linkages
1.Check all linkages for wear, deterioration and
damage. Renew parts as necessary
See
Repair, Track Rod and Linkage
,See Repair,
Drag Link and Drag Link Ends
.

STEERING
1
ADJUSTMENT POWER STEERING BOX - ADJUST
Service repair no - 57.35.01
WARNING: Adjustments of steering box
should not be required while in warranty
period. If box is stiff or tight and within
warranty, it must be returned to manufacturer. No
attempt must be made to introduce backlash.
1.Apply park brake brake, chock wheels and Jack
up front of vehicle until wheels are clear of
ground.
2.Support chassis front on axle stands.
3.Disconnect drag link from steering drop arm.
4.Check torque to turn
See Fault diagnosis,
Stiff Steering Checklist
.
5.Centralise steering box
See Centralise
Steering Box
.
NOTE: Only check for no backlash when
steering box is in central position.
NOTE: If steering wheel is not straight, it
should be repositioned
See Repair,
Steering Wheel
.
6.Adjustment is obtained by rocking the drop arm
about centre whilst an assistant slowly tightens
the steering box adjuster screw.
7.Tighten locknut when all backlash has been
removed.8.Repeat the check for backlash. If backlash exists
loosen locknut and repeat adjustment
procedure.
9.Turn steering wheel lock to lock and check no
tightness exists.
10.Ensure front wheels are aligned and in straight
ahead position.
11.Adjust drag link 924 mm between ball joint
centres.
12.Connect drag link and tighten to
40 Nm (30
lbf/ft).
13.Lower vehicle to ground level and remove
chocks.
14.Road test vehicle
See Fault diagnosis, Road
Test Procedure
.
Drag link adjust
1.RH drive vehicles - if steering wheel is to right,
drag link is too long. If steering wheel is to left
drag link is too short.
LH drive vehicles - if steering wheel is to right,
drag link is too short. If steering wheel is to left
drag link is too long.
2.Adjust drag link until steering wheel points
straight ahead when vehicle is travelling in a
straight line.
CENTRALISE STEERING BOX
Service repair no - 57.35.05
LH drive vehicle
1.Disconnect drag link from drop arm
See Repair,
Drag link and drag link ends
.
2.Turn steering wheel on full RH lock.
3.Turn steering wheel back exactly two turns.
4.Fit drag link
See Repair, Drag link and drag
link ends
.
RH drive vehicle
1.Repeat operation for LH drive vehicle but turn
steering wheel on full LH lock.

57STEERING
2
ADJUSTMENT STEERING LOCK STOPS
Service repair no - 57.65.03
Check
1.Measure clearance between tyre wall and radius
arm at full lock. This must be not less than 20
mm.
Adjust
2.Loosen stop bolt locknut.
3.Turn stop bolt as required.
4.Tighten locknut.
5.Check clearance between tyre wall and radius
arm on each lock.
NOTE: Alternatively lock stop adjustment
may be carried out using following
procedure.
Check
1.Measure stop bolt protrusion 'A'. Refer to table
for correct setting.
Adjust
2.Loosen stop bolt locknut.
3.Turn stop bolt as required.
4.Tighten locknut.
5.Check wheel position at full lock.LOCK STOP SETTINGS
Tyre & wheel size - alloys
Make Size Setting
BF Goodrich Mud Terrain 265 59,7 mm
Goodyear GT+4 235 55,7 mm
Michelin M+S 4x4 235 54,2 mm
Tyre & wheel size - steel
Make Size Setting
Goodyear 205 52,2 mm
Michelin 205 52,2 mm
Avon 7.50 56 mm
Michelin 7.50 56 mm
Goodyear 7.50 56 mm

STEERING
3
ADJUSTMENT FRONT WHEEL ALIGNMENT
Service repair no - 57.65.01
Checking Toe-out dimensions
NOTE: Recognised front wheel alignment
and tracking equipment should be used
for this operation. Only the use of basic
equipment is described below. No Adjustment is
provided for castor, camber or swivel pin
inclinations.
1.Set vehicle on level ground with road wheels
positioned straight ahead.
2.Push vehicle back and forwards to settle linkage.
3.Set up the equipment to manufacturers
instructions and check alignment as advised by
equipment supplier.
4.Position trammel probes on inner face of wheel,
not the rims, if the latter are damaged.
5.Measure toe-out at horizontal centre-line of
wheels.
6.Check tightness of clamp bolt fixings. Tighten to
14 Nm (10lbf/ft).
Adjust
7.Slacken clamps at both ends of track rod.
8.Rotate track rod to increase or decrease its
effective length until correct toe-out is obtained
See GENERAL SPECIFICATION DATA,
Information, Steering
.
9.Push vehicle rearwards turning steering wheel
from side to side to settle ball joints. With road
wheels set in straight ahead position, push
vehicle forward a short distance.
10.Recheck track and adjust if necessary.
11.When alignment is correct, tap ball joints in
direction of arrows to maximum of travel, to
ensure full unrestricted movement of track rod.
12.Tighten clamp bolts to
14 Nm (10 lbf/ft).
POWER STEERING PUMP DRIVE BELT
Service repair no - 57.20.01
Adjust
NOTE: For details of drive belt adjust
procedure.
See ELECTRICAL, Repair,
Auxiliary Drive Belt

STEERING
1
REPAIR STEERING COLUMN
Service repair no - 57.40.01
Remove
1.Remove bonnet.
2.Set road wheels and steering wheel in straight
ahead position.
3.Mark relationship of steering column inner shaft
to top universal joint.
NOTE: collapsible shaft can be
disconnected from steering column only, if
required, by removing bolts from top
universal joint and slackening top bolt of lower
universal joint.
4.Remove 2 bolts from top universal joint and
lower bolt of bottom universal joint. Slacken top
bolt of lower universal joint and withdraw shaft.5.Prise centre cap from steering wheel.
6.Remove steering wheel retaining nut and
withdraw wheel from column spline.
7.Disconnect battery.
8.Remove 4 screws securing instrument panel and
pull panel away from facia to enable
speedometer cable to be disconnected.
9.Disconnect multi-plugs, electrical leads and
connections to vehicle alarm system, if fitted.
See ELECTRICAL, Repair, Vehicle
immobilisation and alarm system
.
10.Withdraw panel complete with instruments.
11.Remove 5 screws and 2 self-tapping screws to
remove top half of nacelle.
12.Ease bottom half of nacelle from switch
gaiters/grommets and remove.

STEERING
3
REPAIR REV: 05/99
NOTE: The steering column is a non
serviceable component and can only be
serviced as a complete assembly.
25.Fit main support bracket and padding to steering
column and manoeuvre column into position in
vehicle.
26.Loosely secure main support bracket and
harness bracket to bulkhead.
27.Loosely fit clamp and rubber packing strip to
column.
28.Loosely secure lower end of column to lower
support bracket.
29.Loosely secure clamp bracket to main support
bracket.
30.Working inside vehicle cab, fit tie-bar to column
bracket and secure with single bolt to
22 Nm (16
lbf/ft).
31.Finally, tighten main support bracket, clamp
bracket, upper clamp, and lower support bracket
nuts and bolts. (M6 bolts
9 Nm (6 lbf/ft),M8
bolts
22 Nm (16 lbf/ft).
32.Fit brake pedal boxSee BRAKES, Repair,
Brake pedal
.
33.Fit steering lock/switch in position and rotate
steering column inner shaft to line up slot with
switch plunger.
34.Secure lock to column with clamp and shear
bolts. Evenly tighten bolts but do not shear them.
35.Temporarily fit steering wheel and operate
switch and lock mechanism several times to
ensure it functions correctly.
36.Fully tighten switch retaining bolts until heads
shear.
37.Connect electrical leads to rear of switch. Fit
alarm system passive coil, if applicable.
See
ELECTRICAL, Repair, Vehicle immobilisation
and alarm system
.
38.Fit switch assembly on steering column and
tighten clamping screw.
39.Connect switch assembly multi-plugs and
electrical leads to main harness.
40.Offer up instrument panel, connect speedometer
cable, multi-plugs and electrical leads to main
harness. If applicable, fit vehicle alarm system
connections.
See ELECTRICAL, Repair,
Vehicle immobilisation and alarm system
.
41.Secure panel with 4 screws.
42.Locate top half of nacelle in position and fit to
switch gaiters/grommets.43.Fit lower half of nacelle and loosely tighten fixing
screws.
44.Ensure switch gaiters/grommets are correctly
located and fully tighten fixings.
45.Turn indicator cancelling ring so that slots are
vertical and lug with arrow points to the left, in
direction of indicator switch.
46.Fit steering wheel with finisher attachment lug at
bottom, ensuring that indicator cancelling forks
locate in cancelling ring slots.
47.Secure wheel with nut and new shake-proof
washer. Tighten to
43 Nm (32 lbf/ft).
48.Fit steering wheel decal.
49.If necessary, fit new universal joints to support.
Note that long joint is fitted to short length of
shaft and short joint to long end. Joints can only
be fitted one way to shaft.
50.With steering lock engaged and road wheels in
straight ahead position, align reassembly marks,
and fit collapsible shaft assembly with long leg of
shaft to steering box. Fit pinch bolts and tighten
to
25 Nm (18 lbf/ft).

57STEERING
4
REPAIR POWER STEERING BOX
Service repair no - 57.10.01
NOTE: A chassis undertray may be fitted
on some vehicle derivatives to conform to
legal requirements. When under chassis
remove and refit procedures are required, it may
be necessary to remove the undertray
See
CHASSIS AND BODY, Repair, Front undertray
.
General precautions
·Whenever any part of system, is removed or
disconnected, utmost cleanliness must be
observed.
·Disconnected ports and hoses must be
plugged to prevent ingress of dirt. If metal
sediment is found in system, establish cause,
rectify and flush system.
·Do not start engine until reservoir is full as
pump will be damaged.
·Metric pipe fittings are used with 'O' ring pipe
ends on fittings to steering box.
·Follow normal 'O' ring replacement procedure
whenever pipes are disconnected.
·Ensure compatible metric components when
fitting replacement pipes.
CAUTION: After refitting steering linkage
parts follow correct procedure to ensure
that road wheels, steering box and
steering wheel are correctly positioned relative to
each other when in straight ahead condition.
NOTE: When drag link is disconnected
from steering box, travel available at
steering wheel to each full lock is not
equal.
Remove
1.Site vehicle on level surface.
2.Apply park brake, chock rear wheels, raise
vehicle and locate axle stands. Alternatively,
raise vehicle on a hoist.
3.Remove road wheel.
4.Remove panhard rod
See FRONT
SUSPENSION, Repair, Panhard rod
.
5.Disconnect steering damper from drag link.
6.Disconnect drag link from drop arm, see J6305
on opposite page, using a suitable extractor.
7.Slacken, but do not remove nut securing tie bar
to mounting arm.8.Remove 2 bolts securing tie bar to steering box
and move aside.
9.Remove filler cap from power steering fluid
reservoir.
10.Position suitable container under steering box.
11.Disconnect feed and return pipes from steering
box and drain fluid.
12.Plug open pipes and steering box ports to
prevent ingress of dirt. Refit fluid reservoir filler
cap.
13.Centralise steering
See Centralise steering
box
.
14.Remove pinch bolt securing lower shaft
universal joint to power steering box.
15.Remove 4 bolts and 2 tab washers securing
steering box to chassis side member.
16.Withdraw steering box.
17.Clean all mounting faces, unions etc. prior to
refitting.
Refit
18.Position steering box to chassis side member,
ensuring locating peg is engaged. Fit tab
washers and tighten bolts to
81 Nm (60 lbf/ft).
19.Fit pinch bolt and nut securing universal joint to
power steering box spline. Tighten to
25 Nm (18
lbf/ft).
20.Secure tie bar to mounting arm and steering box.
Tighten fixings to
81 Nm (60 lbf/ft),starting with
tie bar to mounting nut, then loosen fixings by
one complete turn.
21.Check steering box and adjust if necessary
See
Adjustment, Power steering box - adjust
.
22.Refit drag link to drop arm and tighten nut to
40
Nm (30 lbf/ft).
Fit new split pin to retaining nut.

STEERING
5
REPAIR REV: 05/99
23.Fit panhard rodSee FRONT SUSPENSION,
Repair, Panhard rod
.
24.Fit road wheels. Lower vehicle to ground and
tighten wheel nuts to correct torque:
Alloy wheels - 130 Nm (96 lbf/ft)
Steel wheels - 100 Nm (80 lbf/ft)
Heavy duty wheels - 170 Nm (125 lbf/ft)
25.Remove plugs and refit feed and return pipes to
steering box. Tighten 16mm thread to
20 Nm (15
lbf/ft),
14mm thread to15 Nm (11 lbf/ft).
26.Remove filler cap. Fill reservoir to oil level mark
on dipstick, using recommended fluid
See
LUBRICANTS, FLUIDS AND CAPACITIES,
Information, Recommended lubricants and
fluids
.
27.Bleed power steering system
See Power
steering system - bleed
.
28.Recheck fluid level and replace cap.
29.With engine running, test steering system for
leaks by holding steering in both full lock
directions.
CAUTION: Do not maintain this pressure
for more than 30 seconds in any one
minute, to avoid oil overheating and
possible seal damage.
30.Test drive vehicle: using both full lock directions,
to settle steering components. If possible, drive
vehicle over uneven ground and include harsh
braking.
WARNING: Do not test drive vehicle on
public highway.
31.Drive vehicle in a straight line on level ground
and stop.
32.Tighten tie bar to mounting nut to
110 Nm (81
lbf/ft).
33.Tighten tie bar to steering box fixings to81 Nm
(60 lbf/ft).
34.Ensure steering wheel is correctly aligned when
wheels are positioned straight ahead.
35.If necessary, reposition steering wheel
See
Steering wheel
.
36.Road test vehicle.

57STEERING
6
REPAIR POWER STEERING SYSTEM - BLEED
Service repair no - 57.15.02
1.Check that fluid level is at maximum level
See
MAINTENANCE , Under bonnet maintenance.
2.Run engine to normal operating temperature.
3.Recheck reservoir fluid level, top up if necessary
NOTE: During operations 4 to 6, maintain
maximum fluid level in reservoir. Do not
increase engine speed or move steering
wheel.
4.With engine at idle speed, slacken bleed screw.
When fluid seeps past bleed screw retighten
screw.
5.Check fluid level.
6.Clean away fluid around bleed screw.
7.Check hose connections, pump and steering box
for fluid leaks by holding steering on full lock in
both directions.
CAUTION: Do not maintain this pressure
for more than 30 seconds in any one
minute to avoid overheating fluid and
possibly damaging seals.
8.Carry out road test.POWER STEERING FLUID RESERVOIR
Service repair no - 57.15.08
Remove
1.Position drain tin beneath reservoir.
2.Slacken mounting bracket clamp bolt and raise
reservoir to gain access to feed and return hose
retaining clips.
3.Slacken clips, disconnect hoses from reservoir,
allow fluid to drain.
4.Remove reservoir.
CAUTION: Plug connections to prevent
ingress of dirt.
CAUTION: Discard fluid drained from
system. Do not allow fluid to contact
paintwork, if spilled, remove fluid and
clean area with warm water.
Refit
5.Position reservoir, connect feed and return
hoses and tighten clips to
3 Nm (2 lbf/ft).
6.Fit reservoir in clamp, tighten clamp bolt.
7.Fill reservoir between upper mark and end of
dipstick with power steering fluid
See
MAINTENANCE , Under bonnet maintenance
.
8.Bleed power steering system
See Power
steering system - bleed
.