engine oil LAND ROVER DEFENDER 1996 Workshop Manual

INTRODUCTION
3
INFORMATION SYNTHETIC RUBBER
Many 'O' ring seals, flexible pipes and other similar
items which appear to be natural rubber are made of
synthetic materials called Fluoroelastomers. Under
normal operating conditions this material is safe, and
does not present a health hazard. However, if the
material is damaged by fire or excessive heat, it can
break down and produce highly corrosive Hydrofluoric
acid which can cause serious burns on contact with
skin. Should the material be in a burnt or overheated
condition handle only with seamless industrial gloves.
Decontaminate and dispose of the gloves immediately
after use.
If skin contact does occur, remove any contaminated
clothing immediately and obtain medical assistance
without delay. In the meantime, wash the affected
area with copious amounts of cold water or limewater
for fifteen to sixty minutes.
RECOMMENDED SEALANTS
A number of branded products are recommended in
this manual for use during maintenance and repair
work.
These items include:
HYLOMAR GASKET AND JOINTING COMPOUND
and
HYLOSIL RTV SILICONE COMPOUND.
They should be available locally from garage
equipment suppliers. If there is any problem obtaining
supplies, contact the following company for advice
and the address of the nearest supplier.
MARSTON LUBRICANTS LTD.
Hylo House,
Cale Lane,
New Springs,
Wigan WN2 1JR
Tel 01942 824242USED ENGINE OIL
WARNING: Prolonged and repeated
contact with engine or motor oil will result
in the removal of natural fats from the
skin, leading to dryness, irritation and dermatitis.
Used engine oil contains potentially harmful
contaminants which may cause skin cancer.
Adequate means of skin protection and washing
facilities should be provided.
Handling precautions
1.Avoid prolonged and repeated contact with oils,
particularly used engine oils.
2.Wear protective clothing, including impervious
gloves where applicable.
3.Do not put oily rags in pockets.
4.Avoid contaminating clothes, particularly
underwear, with oil.
5.Overalls must be cleaned regularly. Discard
unwashable clothing and oil impregnated
footwear.
6.First aid treatment must be obtained immediately
for open cuts and wounds.
7.Use barrier creams, before each work period, to
help the removal of oil from the skin.
8.Wash with soap and water to ensure all oil is
removed (skin cleansers and nail brushes will
help). Preparations containing lanolin replace the
natural skin oils which have been removed.
9.Do not use gasoline, kerosene, diesel fuel,
petrol, thinners or solvents for washing the skin.
10.If skin disorders develop, obtain medical advice.
11.Where practicable, degrease components prior
to handling.
12.Where there is a risk of eye contact, eye
protection should be worn, for example, goggles
or face shields; in addition an eye wash facility
should be provided.
Disposing of used oils
Environmental protection precaution
It is illegal to pour used oil onto the ground, down
sewers or drains, or into waterways.
Dispose of used oil through authorised waste disposal
contractors. If in doubt contact your Local Authority for
advice on disposal facilities.

01INTRODUCTION
8
INFORMATION JUMP STARTING
WARNING: Hydrogen and oxygen gases
are produced during normal battery
operation. This gas mixture can explode if
flames, sparks or lighted tobacco are brought
near battery. When charging or using a battery in
an enclosed space, always provide ventilation and
shield your eyes.
Keep out of reach of children. Batteries contain
sulphuric acid. Avoid contact with skin, eyes, or
clothing. Also, shield eyes when working near
battery to protect against possible splashing of
acid solution. In case of acid contact with skin,
eyes, or clothing, flush immediately with water for
a minimum of fifteen minutes. If acid is swallowed,
drink large quantities of milk or water, followed by
milk of magnesia, a beaten egg, or vegetable oil.
SEEK MEDICAL AID IMMEDIATELY.
To Jump Start - Negative Ground Battery
WARNING: To avoid any possibility of
injury use particular care when connecting
a booster battery to a discharged battery.
1.Position vehicles so that jump leads will reach,
ensuring that vehiclesDO NOT TOUCH,
alternatively a fully charged slave battery may be
positioned on floor adjacent to vehicle.
2.Ensuring that ignition and all electrical
accessories are switched off, that parking brake
is applied and neutral is selected, connect the
jump leads as follows;
A.Connect one end of first jumper cable to positive
(+) terminal of booster battery.
B.Connect other end of first jumper cable to positive
(+) terminal of discharged battery.
C.Connect one end of second jumper cable to
negative terminal of booster battery.
D.Connect other end of second jumper cable to a
good earth point on the disabled vehicle (eg. engine
front lifting eye, as shown in J6086),NOT TO
NEGATIVE TERMINAL OF DISCHARGED
BATTERY.Keep jumper lead away from moving
parts, pulleys, drive belts and fan blade assembly.
WARNING: Making final cable connection
could cause an electrical arc which if
made near battery could cause an
explosion.
3.If booster battery is installed in another vehicle,
start engine and allow to idle.
4.Start engine of vehicle with discharged battery,
following starting procedure in Owners' Manual.
CAUTION: If vehicle fails to start within a
maximum time of 12 seconds, switch
ignition off and investigate cause. Failing
to follow this instruction could result in
irrepairable damage to catalyst, if fitted.
5.Remove negative (-) jumper cable from the
engine and then terminal of booster battery.
6.Remove positive (+) jumper cable from positive
terminals of booster battery and discharged
battery.

GENERAL SPECIFICATION DATA
1
INFORMATION REV: 05/99 300Tdi ENGINE
Type Direct injection, turbocharged, intercooled.................................................................................
Number of cylinders 4.........................................................
Bore 90,47 mm.................................................................................
Stroke 97,00 mm...............................................................................
Capacity 2495 cc...........................................................................
Compression ratio 19.5:1±0.5:1 ............................................................
Valve operation O.H.V. pushrod operated................................................................
Crankshaft
Main bearing journal diameter 63,475 - 63,487 mm..........................................
Regrind dimensions 63,233 - 63,246 mm.........................................................
Crankpin journal diameter 58,725 - 58,744 mm................................................
Regrind dimensions 58,471 - 58,490 mm.........................................................
Crankshaft end thrust Taken on thrust washers at centre main bearing.......................................................
Crankshaft end float 0,05 - 0,15 mm.........................................................
Main bearings
Number and type 5 halved shells with oil grooves..............................................................
Diametrical clearance 0,0792 - 0,0307 mm.......................................................
Connecting rods
Length between centres 175,38 - 175,43 mm...................................................
Diametrical clearance (big-end bearings) 0,025 - 0,075 mm........................
End float on crankpin 0,15 - 0,356 mm.......................................................
Pistons
Type Aluminium alloy, combustion chamber in crown..................................................................................
Graphite coating on sidewalls.
Skirt diametrical clearance (at r/angle to gudgeon pin) 0,025 - 0,05 mm....
Maximum height above combustion face 0,8 mm.........................
Gudgeon pins
Type Fully floating.................................................................................
Fit in piston Hand push fit.......................................................................
Diameter 30,156 - 30,163 mm..........................................................................
Clearance in connecting rod 0,003 - 0,016 mm............................................
Piston rings
Type:
- Top Barrel edge, chrome plated........................................................................
- Second Taper faced..................................................................
- Oil control Expander and rails..............................................................
Gap in bore:
- Top 0,40 - 0,60 mm........................................................................
- Second 0,30 - 0,50 mm..................................................................
- Oil control 0,30 - 0,60 mm..............................................................
Clearance in piston grooves:
- Second 0,050 - 0,085 mm..................................................................
- Oil control 0,050 - 0,085 mm..............................................................

04GENERAL SPECIFICATION DATA
2
INFORMATION Camshaft
Drive 30 mm wide dry toothed belt.................................................................................
Location Right hand side (thrust side)...........................................................................
End float 0,1 - 0,2 mm...........................................................................
Number of bearings 4..........................................................
Material Steel shell, white metal lined............................................................................
Valves
Tappet clearance:
- Inlet and exhaust 0,20 mm...................................................
Seat angle:
- Inlet 30° .......................................................................
- Exhaust 45° .................................................................
Head diameter:
- Inlet 38,75 - 39,05 mm.......................................................................
- Exhaust 36,35 - 36,65 mm.................................................................
Stem diameter:
- Inlet 7,960 - 7,975 mm.......................................................................
- Exhaust 7,940 - 7,960 mm.................................................................
Valve lift:
- Inlet 9,67 mm.......................................................................
- Exhaust 9,97 mm.................................................................
Cam lift:
- Inlet 6,81 mm.......................................................................
- Exhaust 7,06 mm.................................................................
Valve head stand down:
- Inlet 0,81 - 1,09 mm.......................................................................
- Exhaust 0,86 - 1,14 mm.................................................................
Valve springs
Type Single coil.................................................................................
Length, free 46,28 mm......................................................................
Length, under 21 kg load 40,30 mm.................................................
Lubrication
System Wet sump, pressure fed.............................................................................
Pressure, engine warm at normal operating speeds 1,76 - 3,87Kgf/cm
2(25 - 55 Ibf/in2) ........
Oil pump:
- Type G-rotor integral with front cover.......................................................................
- Drive off crankshaft nose.....................................................................
Oil pressure relief valve Non-adjustable....................................................
Relief valve spring:
- Full length 51,6mm......................................................................
- Compressed length at 7.71Kg load 31mm................................
Oil filter Screw-on disposable canister.............................................................................
Engine oil cooler Combined with coolant radiator and intercooler...............................................................

GENERAL FITTING REMINDERS
5
INFORMATION JOINTS AND JOINT FACES
1.Always use correct gaskets where they are
specified.
2.Use jointing compound only when
recommended. Otherwise fit joints dry.
3.When jointing compound is used, apply in a thin
uniform film to metal surfaces; take great care to
prevent it from entering oilways, pipes or blind
tapped holes.
4.Remove all traces of old jointing materials prior
to reassembly. Do not use a tool which could
damage joint faces.
5.Inspect joint faces for scratches or burrs and
remove with a fine file or oil stone; do not allow
removed material or dirt to enter tapped holes or
enclosed parts.
6.Blow out any pipes, channels or crevices with
compressed air, fit new 'O' rings or seals
displaced by air blast.FLEXIBLE HYDRAULIC PIPES, HOSES
1.Before removing any brake or power steering
hose, clean end fittings and area surrounding
them as thoroughly as possible.
2.Obtain appropriate plugs or caps before
detaching hose end fittings, so that ports can be
immediately covered to exclude dirt.
3.Clean hose externally and blow through with
airline. Examine carefully for cracks, separation
of plies, security of end fittings and external
damage. Reject any hose found faulty.
4.When refitting hose, ensure that no unnecessary
bends are introduced, and that hose is not
twisted before or during tightening of union nuts.
5.Containers for hydraulic fluid must be kept
absolutely clean.
6.Do not store brake fluid in an unsealed
container. It will absorb water, and fluid in this
condition would be dangerous to use due to a
lowering of its boiling point.
7.Do not allow brake fluid to be contaminated with
mineral oil, or use a container which has
previously contained mineral oil.
8.Do not re-use brake fluid bled from system.
9.Always use clean brake fluid to clean hydraulic
components.
10.Fit a cap to seal a hydraulic union and a plug to
its socket after removal to prevent ingress of dirt.
11.Absolute cleanliness must be observed with
hydraulic components at all times.
12.After any work on hydraulic systems, inspect
carefully for leaks underneath the vehicle while a
second operator applies maximum pressure to
the brakes (engine running) and operates the
steering.

09LUBRICANTS, FLUIDS AND CAPACITIES
2
INFORMATIONREV: 05/99 Propeller shaft Front
and RearNLGI - 2 Multi-purpose Lithium based GREASE
Lubrication nipples
(hubs, ball joints
etc.)
Seat slides
Door lock striker
Brake and clutch
reservoirsBrake fluids having a minimum boiling point of 260°C (500°F) and complying with
FMVSS 116 DOT4
Engine coolant
(Pre-99MY)Use an ethylene glycol based anti-freeze (containing no methanol) with non-phosphate
corrosion inhibitors suitable for use in aluminium engines to ensure the protection of the
cooling system against frost and corrosion in all seasons. Use one part anti-freeze to
one part water for protection down to -36°C (-33°F).
IMPORTANT: Coolant solution must not fall below proportions one part
anti-freeze to three parts water, i.e. minimum 25% anti-freeze in coolant otherwise
damage to engine is liable to occur. Maximum concentration is 60%.
Engine coolant
(99MY on)Use Texaco XLC long life coolant. Use one part anti-freeze to one part water for
protection down to -36°C (-33°F).
IMPORTANT: Coolant solution must not fall below 50% anti-freeze otherwise
damage to the engine is liable to occur. Maximum concentration is 60%.
Battery lugs, Petroleum jelly.
earthing surfaces
where paint has
been removed.NOTE: Do not use Silicone Grease
Air Conditioning
System Refrigerant Use only refrigerant R134a
Compressor Oil Sanden oil
LUBRICATION PRACTICE
Use a high quality oil of the correct viscosity range and service classification in the engine during maintenance and
when topping up. The use of oil not to the correct specification can lead to high oil and fuel consumption and
ultimately to damaged components.
Oil to the correct specification contains additives which disperse the corrosive acids formed by combustion and
prevent the formation of sludge which can block the oilways. Additional oil additives should not be used. Always
adhere to the recommended servicing intervals.
WARNING: Many liquids and other substances used in motor vehicles are poisonous. They must
not be consumed and must be kept away from open wounds. These substances, among others,
include anti-freeze, windscreen washer additives, lubricants and various adhesives.

LUBRICANTS, FLUIDS AND CAPACITIES
3
INFORMATION REV: 05/99 CAPACITIES
The following capacity figures are approximate and are provided as a guide only.
Capacities (approx.)* Litres Pints
Engine sump oil 5,8................................................................ 10.20
Extra when refilling after fitting new filter 0,85.......................... 1.50
Manual gearbox 2,67............................................................... 4.70
Transfer gearbox oil 2,30......................................................... 4.00
Front differential 1,70............................................................... 3.00
Rear differential 1,70................................................................ 3.00
Power steering box and reservoir LHD 2,90............................ 5.00
Power steering box and reservoir RHD 3,40............................ 6.00
Swivel pin housing oil/grease (each) 0,35................................ 0.60
Fuel tank usable fuel 79,5........................................................ 17.5 gall
Cooling system 11,50................................................................ 20.20
Washer bottle 3,0................................................................... 5.28
NOTE: * All levels must be checked by dipstick or level plugs as applicable.
ANTI-FREEZE
PERCENTAGE CONCENTRATION - 50%
PROTECTION - LOWER TEMPERATURE LIMIT
Complete protection
Vehicle may be driven away immediately from cold,
-33°C (-36°F).
Safe limit protection
Coolant in semi-frozen state. Engine may be started
and driven away after warm-up period, -41°C (-42°
F).Lower protection
Prevents frost damage to cylinder head, block and
radiator. Thaw out before starting engine, -47°C (-53°
F).
CAUTION: Anti-freeze content must never
be allowed to fall below 25% (pre 99MY) or
50% (99MY on) otherwise damage to the
engine is liable to occur. Anti-freeze content
should not exceed 60% (all models) as this will
greatly reduce cooling efficiency.

MAINTENANCE
3
MAINTENANCE UNDER BONNET MAINTENANCE
UNDER BONNET COMPONENTS
A - RH drive
1.Brake fluid reservoir
2.Clutch fluid reservoir
3.Air cleaner element
4.Engine breather filter
5.Oil filler cap
6.Oil level dipstick
7.Heater/air conditioning unit
8.Windscreen washer reservoir
9.Power steering pump reservoir10.Intercooler and hoses
11.Radiator filler plug
12.Radiator
13.Oil cooler
14.Fuel filter
15.Accelerator linkage
16.Expansion tank
17.Air cleaner dump valve

10MAINTENANCE
4
MAINTENANCE
UNDER BONNET COMPONENTS
B - LH drive
1.Brake fluid reservoir
2.Clutch fluid reservoir
3.Air cleaner element
4.Engine breather filter
5.Oil filler cap
6.Oil level dipstick
7.Heater/air conditioning unit
8.Windscreen washer reservoir
9.Power steering pump reservoir10.Intercooler and hoses
11.Radiator filler plug
12.Radiator
13.Oil cooler
14.Fuel filter
15.Accelerator linkage
16.Expansion tank
17.Air cleaner dump valve

MAINTENANCE
9
MAINTENANCE REV: 05/99 UNDER VEHICLE MAINTENANCE
NOTE: A chassis undertray may be fitted
on some vehicle derivatives to conform to
legal requirements. When under chassis
maintenance, or remove and refit procedures are
required, it may be necessary to remove the
undertray and/or integral access panels
See
CHASSIS AND BODY, Repair, Front undertray
or
See CHASSIS AND BODY, Repair, Rear undertray
RENEW ENGINE OIL AND FILTER
1.Ensure vehicle is level.
2.Run engine to warm oil, switch off ignition.
3.Disconnect battery.
4.Place suitable drain tray under sump drain plug.
5.Remove drain plug from sump and allow oil to
drain completely.
6.Fit new sealing washer, replace plug and tighten
to
35 Nm (26 lbf/ft).
7.Place drain tray under oil filter.
8.Unscrew filter anti-clockwise, using a strap
wrench if necessary.
9.Clean mating face of oil filter adaptor.
10.Coat rubber sealing washer of new filter with
clean engine oil.
11.Screw filter on clockwise until sealing washer
touches adaptor mating face, tighten a further
half turn by hand only. DO NOT overtighten.
12.Clean and remove filler cap from rocker cover.
13.Pour in correct quantity and grade of new oil
from a sealed container.
See LUBRICANTS,
FLUIDS AND CAPACITIES, Information,
Recommended lubricants and fluids
14.Check that oil level is between upper and lower
marks on dipstick. DO NOT fill above upper
mark.
15.Firmly replace filler cap.
16.Reconnect battery, run engine and check oil filter
for leaks.
17.Stop engine, allow oil to run back into sump for a
few minutes and check oil level again. Top up if
necessary.