check engine LAND ROVER DEFENDER 1999 User Guide

12ENGINE
2
REPAIR
13.Position camshaft in camshaft carrier.
14.Check end-float of camshaft using a DTI.
Camshaft end-float = 0.06 to 0.16 mm (0.002 to
0.006in).
15.Renew components as necessary to achieve
correct end-float.
CAUTION: Cylinder head and camshaft
carrier are machined together as an
assembly. If bearing surfaces in either
component are found to be damaged, complete
assembly must be replaced.
NOTE: The procedure for checking
camshaft bearing clearances is covered in
Td5 Engine Overhaul section - Cylinder
head - overhaul.Refit
16.Using a suitable cleaning solvent, clean mating
faces of cylinder head and camshaft carrier.
17.Blow out all oilways and waterways.
18.Ensure threaded holes in cylinder head and
camshaft carrier are clean and dry.
CAUTION: Support each end of the
cylinder head on blocks of wood. With
camshaft carrier bolted down some valves
and the injector nozzles will protrude from the
face of cylinder head.
19.Fit new adjusting screws fully into rocker arms.
Fit new lock nuts to screws but do tighten.
CAUTION: Ensure screws are correct for
type of rocker arms fitted. Replacement
screws for Engine Serial No. Prefixes 15P
to 19P have a centre punch mark adjacent to the
adjusting screw slot. These screws are not
interchangeable with those fitted to Engine Serial
No. Prefixes 10P to 14P.
20.Lubricate cams and bearing journals on
camshaft, cylinder head and camshaft carrier
with clean engine oil.
21.Position camshaft in cylinder head with the
timing pin hole in the vertical position.
22.Apply an even film of sealant, Part No. STC
4600 to camshaft carrier face as shown and
spread to an even film using a roller.
CAUTION: Ensure sealant does not block
oilways (arrowed) or contaminate
camshaft bearings. Assembly and bolt
tightening must be completed within 20 minutes
of applying sealant.
23.Fit camshaft carrier ensuring that it is correctly
located on dowels.
24.Fit and lightly tighten camshaft carrier bolts.
ProCarManuals.com

12ENGINE
10
REPAIR Refit
39.Clean mating faces of cylinder head and cylinder
block.
40.Check cylinder head for warping, across centre
and from corner to corner:
Maximum warp = 0.10 mm (0.004 in)
CAUTION: Cylinder heads may not be
refaced, replace cylinder head assembly if
warping exceeds figure given.
41.Ensure coolant and oil passages are clean.
42.Clean dowel holes and fit new dowels.
43.Fit new cylinder head gasket of the correct
thickness with the word’TOP’uppermost.
44.Using assistance, fit cylinder head and locate on
to dowels.
45.Carefully enter new cylinder head bolts together
with their captive washers,DO NOT DROP.
Lightly tighten bolts.
46.Using sequence shown, tighten cylinder head
bolts to:-
Stage 1 -30 Nm (23 lbf.ft)
Stage 2 -65 Nm (48 lbf.ft)
Stage 3 -90°
Stage 4 -Further 180°
Stage 5 -Further 45°
CAUTION: Ensure correct tightening
sequence is followed for all 5 tightening
stages. Do not tighten bolts 315°in one
operation.
47.Fit nut and bolt securing cylinder head to timing
chain cover and tighten to25 Nm (18 lbf.ft).
48.Clean camshaft sprocket and mating face on
camshaft.
49.Ensure engine is set to TDC No. 1 cylinder and
mark on camshaft sprocket is positioned
between the 2 coloured links.
50.Position camshaft sprocket to camshaft, fit and
lightly tighten new bolts then loosen bolts half a
turn.
51.Clean fixed guide retaining pin and apply Loctite
242 to threads.
52.Fit and tighten fixed guide retaining pin to25 Nm
(18 lbf.ft).
53.Clean timing chain tensioner and fit new sealing
washer.
54.Fit timing chain tensioner and tighten to45 Nm
(33 lbf.ft).
55.Tighten camshaft sprocket retaining bolts to36
Nm (27 lbf.ft).
56.RemoveLRT-12-058from camshaft.
57.RemoveLRT-12-158from gearbox bell housing.
58.Clean access plug recess in cylinder head and
fit new’O’ring. Fit access plug.
59.Clean vacuum pump union.
60.Tighten vacuum pipe union to10 Nm (7lbf.ft).
61.Fit bolts securing alternator bracket to cylinder
head and tighten to25 Nm (18 lbf.ft).
62.Connect top hose, heater hoses and secure with
clips.
ProCarManuals.com

ENGINE
23
REPAIR FILTER - OIL
Service repair no - 12.60.04
Remove
1.Remove 3 bolts and remove engine acoustic
cover.
2.Release clip and disconnect breather hose from
camshaft cover.
3.Release clips and disconnect air flow meter from
air filter.
4.Disconnect multiplug from air flow meter.
5.Loosen clip screw and remove air inlet hose
from turbocharger.
6.Remove 3 bolts and remove manifold heat
shield.
7.Clean area around filter head and place a
container beneath engine.
8.Using a strap wrench, unscrew and discard filter.
Refit
9.Clean mating face of filter head.
10.Lubricate sealing ring of new filter with clean
engine oil.
11.Fit filter and tighten by hand until it seats then
tighten a further half turn.
12.Start and run engine to check for leaks.
13.Stop engine, wait a few minutes, then check oil
level.
14.Top up engine oil.
15.Position exhaust manifold heat shield and
tighten 3 bolts.
16.Position air inlet hose to turbocharger and
tighten clip screw.
17.Connect air flow meter to air filter and secure
clips.
18.Connect air flow meter multiplug.
19.Connect breather hose and secure with clip.
20.Position engine acoustic cover.
ProCarManuals.com

ENGINE
29
REPAIR VALVE - RELIEF - OIL PRESSURE
Service repair no - 12.60.56
Remove
1.Remove sump gasket.See this Section.
2.Remove and discard oil pressure relief valve
plug from oil pump housing.
3.Remove spring and valve.
Refit
4.Clean valve and spring.
5.Clean valve seating inside oil pump housing.
6.Lubricate valve and seating.
7.Fit valve and spring to pump.
8.Apply Loctite 243 sealant to threads of a new
plug.
9.Fit plug and tighten to23 Nm ( 17 lbf.ft).
10.Fit sump gasket.See this Section.
11.Check engine oil level, top-up if necessary.COOLER - ENGINE OIL
Service repair no - 12.60.68
Remove
1.Drain cooling system.See COOLING
SYSTEM, Adjustment.
2.Remove centrifuge assembly.See this
Section.
3.Remove clutch housing bolt and release coolant
pipe from rear of engine.
4.Release clip and coolant hose from oil cooler.
5.Disconnect oil pressure switch multiplug.
6.Remove oil filter element using a suitable strap
wrench.
7.Remove 3 bolts, remove oil filter adaptor and
discard gasket.
8.Remove 7 bolts, remove oil cooler and discard
gasket.
9.Remove oil pressure switch.
ProCarManuals.com

ENGINE
5
OVERHAUL Refit
1.Thoroughly clean cylinder block and cylinder
head mating faces.
2.Ensure coolant and oil passageways are clear
and bolt holes are clean and dry.
3.Ensure locating dowel holes in cylinder block are
clean and dry.
4.Fit new plastic locating dowels in cylinder block.
5.Fit new cylinder head gasket of the correct
thickness with the word’TOP’uppermost.
CAUTION: Gasket must be fitted dry.
6.Ensure that camshaft timing pinLRT-12-158is
still in position and using assistance, fit cylinder
head.
7.Carefully enter new cylinder head bolts together
with their captive washers,DO NOT DROP.
Lightly tighten bolts.
CAUTION: Cylinder head bolts are
pre-lubricated and do not require
additional lubrication.
8.Using sequence shown, tighten cylinder head
bolts to:
Stage 1 -30 Nm (23 lbf.ft)
Stage 2 -65 Nm (48 lbf.ft)
Stage 3 -90
°
Stage 4 -Further 180°
Stage 5 -Further 45°
CAUTION: Ensure correct tightening
sequence is followed for all 5 tightening
stages. Do not tighten bolts 315°in one
operation.9.Fit cylinder head to timing chain cover nut and
bolt and tighten to25 Nm (18 lbf.ft).
10.Clean camshaft sprocket and mating face on
camshaft.
11.Ensure engine is set to TDC firing - No.1
cylinder.
12.Check that mark on camshaft sprocket is
positioned between the 2 coloured links on
timing chain.
13.Position sprocket to camshaft, fit and lightly
tighten 3 new bolts then loosen bolts half a turn.
ProCarManuals.com

ENGINE
11
OVERHAUL
23.Remove 3 bolts and remove fuel connector
block from cylinder head.
24.Remove and discard gasket,’O’ring and fuel
filter.
25.Remove spacer block and gasket (if fitted).Cylinder head and camshaft carrier - cleaning
1.Thoroughly clean cylinder head mating faces,
ensure oil and coolant passages are clear and
bolt holes are clean and dry.
CAUTION: Take care to ensure that EUI
drillings are clear.
2.Using suitable solvent, remove all traces of
sealant and gasket material.
CAUTION: Do not use metal scrapers.
3.Remove all traces of oil from camshaft bearings
and journals.
4.Clean glow plug threads.
Cylinder head - Inspection
1.Check core plugs for signs of leakage and
corrosion, seal replacement plugs with Loctite
243.
2.Check cylinder head for warping across centre
and from corner to corner.
Maximum cylinder head warp =0.1 mm (0.004
in).
CAUTION: Cylinder heads may not be
refaced, replace the head assembly if
warping exceeds the limit given.
ProCarManuals.com

12ENGINE
12
OVERHAUL Lash adjusters and finger followers - Inspection
1.Check lash adjuster bores for scoring and signs
of wear or damage.
2.Check lash adjusters for signs of wear, scoring
and overheating, replace as necessary. Ensure
oil hole in each lash adjuster is clear.
CAUTION: Store lash adjusters upright
and in their fitted order.
3.Check finger followers for wear and that rollers
are free to rotate.
CAUTION: Store finger followers in their
fitted order.
Camshaft - Inspection
1.Check camshaft lobes and bearing journals for
signs of scoring and wear.
2.Check bearing surfaces in cylinder head and
camshaft carrier for signs of scoring and wear.
CAUTION: Cylinder head and camshaft
carrier are machined together as an
assembly, if bearing surfaces in either
component are damaged, both components must
be replaced as an assembly.Camshaft - Check end-float
1.Position camshaft in camshaft carrier.
2.Check end-float of camshaft using a DTI.
Camshaft end-float =0.06 to 0.16 mm (0.002 to
0.006 in).
3.Renew components as necessary to achieve
correct end-float.
ProCarManuals.com

ENGINE
13
OVERHAUL Camshaft bearings - check clearance
1.Position camshaft in cylinder head.
2.Place a piece of Plastigage along the centre line
of each camshaft bearing journal.
3.Carefully fit the camshaft carrier ensuring it is
located on dowels.
CAUTION: Do not rotate camshaft.
4.Fit original camshaft carrier retaining bolts and
tighten in sequence shown to25 Nm (18 lbf.ft).
5.Using sequence shown, loosen then remove
camshaft carrier retaining bolts.
CAUTION: Do not discard bolts at this
stage.
6.Carefully remove camshaft carrier.
7.Measure and record widest portion of Plastigage
on each camshaft bearing journal.
8.Compare figures obtained with camshaft bearing
clearance.
Camshaft bearing clearance =0.04 to 0.10
mm (0.002 to 0.004 in).
9.If any bearing clearance is found to exceed
figures given, repeat the above procedure using
a new camshaft.
CAUTION: If, after repeating the bearing
clearance check with a new camshaft the
bearing clearances are still excessive, a
new cylinder head and camshaft carrier assembly
must be fitted.
10.Remove all traces of Plastigage using an oily
cloth, do not use a scraper.
11.Discard camshaft carrier bolts.
ProCarManuals.com

12ENGINE
14
OVERHAUL Valve springs - Inspection
1.Check free length of valve springs:
Free length =47.0±0.25 mm (1.85±0.011 in)
CAUTION: Valve springs must be replaced
as a set, if springs are to be refitted, keep
them in their fitted order.
Valves and valve guides - Inspection
1.Clean carbon from valves, check valves for
burning, pitting or cracking; replace as
necessary.
2.Clean carbon from valve seat inserts, remove all
loose particles on completion.
3.Check valve seat inserts for pitting and burning.
CAUTION: It is not permissible to recut or
replace valve seat inserts.
4.Remove carbon deposits from valve guides
using toolLRT-12-186.
CAUTION: Tool must be inserted from
combustion chamber face side of cylinder
head, ensure all loose particles of carbon
are removed on completion.
5.Check and record diameter of each valve stem.
Valve stem diameter:
Inlet = 6.907 to 6.923 mm (0.2719 to 0.2725 in)
Exhaust = 6.897 to 6.913 mm (0.2715 to 0.2721
in)
6.Renew any valve if stem diameter is less than
specified.7.Check and record valve stem to guide clearance
using the following procedures:
8.Insert each valve into its respective guide.
9.Extend valve head 10 mm (0.375 in) out of valve
seat and position a DTI gauge to rear of valve
head.
10.Move valve towards front of cylinder head and
zero DTI gauge ensuring that stylus of gauge
remains in contact with valve head.
11.Move valve towards rear of cylinder head, record
gauge reading to give valve stem to guide
clearance.
Valve stem to guide clearance:
Inlet valve = 0.025 to 0.059 mm (0.0009 to
0.0023 in)
Exhaust valve = 0.035 to 0.069 mm (0.0013 to
0.0027 in)
CAUTION: If stem to guide clearance
exceeds figures given and valve stem
diameters were as specified, cylinder head
assembly must be replaced; it is not possible to
replace valve guides.
12.Repeat above procedures for remaining valves.
CAUTION: Keep valves in their fitted order.
13.Check face angle of each valve, renew any
valve with incorrect face angles, do not attempt
to recut.
Valve face angle:
Inlet =29°48’±12’
Exhaust =44°48’±12’
ProCarManuals.com

ENGINE
15
OVERHAUL Valves - Lapping-in
1.Lap each valve to its seat using grinding paste.
2.Apply Prussian Blue to valve seat, insert valve
into guide and press it firmly, without rotating on
to seat.
3.Remove valve and check that a continuous,
even line of Prussian Blue has been transferred
on to valve face.
NOTE: Line does not have to be across
whole width of valve face.
4.Remove all traces of grinding paste on
completion.
5.Check valve head stand-down.See this
Section.
Valve head stand down
1.Insert each valve into its respective guide.
2.Using a straight edge and feeler gauges, check
and record stand down of each valve head.
3.Compare figures obtained with figures given
below.
Valve head stand down:
Inlet valveA= 0.555 to 0.825 mm (0.022 to
0.032 in)
Exhaust valveB= 0.545 to 1.35 mm (0.021 to
0.053 in)
CAUTION: If any valve has a stand down
greater than specified, repeat check using
a new valve. If, after checking with a new
valve, stand down is still excessive, cylinder head
assembly must be replaced. It is not possible to
replace valve seat inserts.Rocker shaft - Dismantling
1.Suitably identify each rocker arm to its fitted
position.
CAUTION: Identify type of rocker arm
fitted. Engine Serial No. Prefixes 10P to
14P - Type A rocker arms. Engine Serial
No. Prefixes 15P to 19P - Type B rocker arms.
Type B rocker arms and type B rocker shaft may
be fitted to Engine Serial No. Prefixes 10P to 14P
as an assembly.
2.Remove and discard spring ring retaining rocker
arm on shaft.
3.Remove rocker arm.
4.Remove and discard 2nd spring ring.
ProCarManuals.com