warning LAND ROVER DEFENDER 1999 User Guide

10 - MAINTENANCE
CONTENTS
Page
MAINTENANCE
UNDERBONNET VIEW - Td5 1..............................................................................
SEATS AND SEAT BELTS 2..................................................................................
LAMPS, HORNS AND WARNING INDICATORS 2................................................
WIPERS AND WASHERS 3...................................................................................
HANDBRAKE 3.......................................................................................................
BATTERY CONDITION - Td5 4..............................................................................
HANDSET BATTERY 5...........................................................................................
HEADLAMP ALIGNMENT 5....................................................................................
ROAD WHEELS 6...................................................................................................
TYRE PRESSURES, CONDITION AND TREAD DEPTH 6....................................
BRAKE PADS, CALIPERS AND DISCS 7..............................................................
ROAD WHEEL SPEED SENSOR HARNESS - Td5 7............................................
FUEL FILTER ELEMENT 8.....................................................................................
FUEL FILTER SEDIMENTER - Td5 8.....................................................................
INTERCOOLER / COOLING SYSTEM 9................................................................
AMBIENT AIR PRESSURE (AAP) SENSOR - Td5 9..............................................
DOOR LOCKS AND HINGES 10............................................................................
ENGINE COOLANT 10...........................................................................................
BRAKE FLUID 11....................................................................................................
AIR FILTER ELEMENT AND DUMP VALVE 11.....................................................
AUXILIARY DRIVE BELT 12...................................................................................
PAS FLUID, CLUTCH FLUID AND SCREEN WASHER LEVELS 12.....................
STEERING BOX 13................................................................................................
ENGINE OIL 14.......................................................................................................
CENTRIFUGE ROTOR - Td5 14.............................................................................
FULL FLOW OIL FILTER 15...................................................................................
GEARBOX OIL 15...................................................................................................
TRANSFER BOX OIL 16.........................................................................................
FRONT AND REAR AXLE OIL 17..........................................................................
PROPELLER SHAFTS 18.......................................................................................
CLUTCH PIPES AND UNIONS 18..........................................................................
PAS PIPES AND UNIONS 19.................................................................................
ENGINE, GEARBOX, TRANSFER BOX AND AXLES 19.......................................
EXHAUST SYSTEM 20...........................................................................................
STEERING BOX AND SUSPENSION 20...............................................................
STEERING BALL JOINTS 21.................................................................................
SHOCK ABSORBERS 22.......................................................................................
TOWING BRACKET 22...........................................................................................
ENGINE AND TRANSMISSION MOUNTINGS 23..................................................
ProCarManuals.com

10MAINTENANCE
2
MAINTENANCE SEATS AND SEAT BELTS
1.Check seat frames are secured to floor and
show no signs of movement.
2.Check operation of seat slide and tilt
mechanisms, ensuring there is no excessive
play between seat cushion and seat back.
3.Check tightness of accessible seat fixings.
4.Fully extract seat belt and allow it to return under
its own recoil mechanism.
5.Check entire length of seat belt webbing for
signs of fraying or damage. Repeat for all belts.
6.Check security of seat belt upper mountings.
7.Check security of seat belt buckle mountings.
8.Connect each belt to the correct buckle, check
seat belt buckle and tongue are secure. Release
seat belt buckle and check for correct operation.
9.Check tightness of accessible seat belt
mountingsLAMPS, HORNS AND WARNING INDICATORS
1.Switch on side, head and tail lights and check
operation.
2.Check headlamp dim/dip operation.
3.Check headlamp levelling operation.
4.Check turn signals and hazard warning lights
operation.
5.Press brake pedal and check operation of brake
lights.
6.Check all exterior lamp lenses for clarity and
condition. Pay particular attention to head lamp
lenses for signs of stone chips or damage.
7.Check horn for loud clear sound.
8.Check operation of all instrument pack warning
and indicator lights.
9.Check for correct operation of interior courtesy
lights.
ProCarManuals.com

10MAINTENANCE
8
MAINTENANCE FUEL FILTER ELEMENT
1.Renew fuel filter element.See FUEL SYSTEM,
Repair.FUEL FILTER SEDIMENTER - Td5
WARNING: Fuel vapour is highly
flammable and in contained speces is also
explosive and toxic. Always have a fire
extinguisher containing FOAM, CO2, GAS OR
POWDER close at hand when handling or draining
fuel.
1.Disconnect battery negative lead.
2.Position suitable container beneath fuel filter
3.Disconnect multiplug from sedimenter
4.Rotate sedimenter anti-clockwise until water
flows from drain tube.
5.Allow to drain until diesel fuel flows from drain
tube.
6.Rotate sedimenter fully clockwise.
7.Connect multiplug.
8.Reconnect battery negative lead.
ProCarManuals.com

10MAINTENANCE
14
MAINTENANCE ENGINE OIL
WARNING: Avoid excessive skin contact
with used engine oil. Used engine oil
contains potentially harmful contaminants
which may cause skin cancer or other serious
skin disorders.
1.Remove underbelly panel.See CHASSIS AND
BODY, Repair.
2.Position suitable container beneath sump.
3.Clean arear around drain plug.
4.Remove oil drain plug, discard sealing washer.
5.Allow oil to drain.
6.Fit new sealing washer to oil drain plug.
7.Fit engine drain plug and tighten to23 Nm (17
lbf.ft).
8.Fill engine with recommended grade of oil to
correct mark on dipstick.See LUBRICANTS,
FLUIDS AND CAPACITIES, Information.
9.Fit underbelly panel.See CHASSIS AND
BODY, Repair.CENTRIFUGE ROTOR - Td5
1.Renew centrifuge rotor.See ENGINE , Repair.
ProCarManuals.com

MAINTENANCE
15
MAINTENANCE FULL FLOW OIL FILTER
1.Renew full flow oil filter.See ENGINE , Repair.GEARBOX OIL
WARNING: Avoid excessive skin contact
with used gearbox oil. Used gearbox oil
contains potentially harmful contaminants
which may cause skin cancer or other serious
skin disorders.
1.Renew gearbox oil.See MANUAL GEARBOX,
Adjustment.
ProCarManuals.com

10MAINTENANCE
16
MAINTENANCE TRANSFER BOX OIL
WARNING: Avoid excessive skin contact
with mineral oil. Mineral oils remove the
natural fats from the skin, leading to
dryness, irritation and dermatitis.
Check
1.Remove underbelly panel.See CHASSIS AND
BODY, Repair.
2.Clean area around oil filler/level plug.
3.Remove oil filler/level plug.
4.Check that oil level is to bottom of oil filler/level
plug hole.
5.Remove all traces of sealant from threads of oil
filler/level plug.
6.Apply Loctite 290 to threads of oil filler/level plug
and tighten to25 Nm (18 lbf.ft).
7.Remove all traces of oil from main casing.
8.Fit underbelly panel.See CHASSIS AND
BODY, Repair.Renew
1.Remove underbelly panel.See CHASSIS AND
BODY, Repair.
2.Place a suitable container beneath transfer box
to catch any fluid spillage.
3.Clean area around oil filler/level and drain plugs.
4.Remove oil filler/level plug.
5.Remove oil drain plug.
6.Allow oil to drain.
7.Apply Loctite 290 to threads of oil drain plug.
8.Fit transfer box drain plug and tighten to30 Nm
(22 lbf.ft).
9.Fill transfer box with recommended oil to bottom
of oil filler/level plug hole.See LUBRICANTS,
FLUIDS AND CAPACITIES, Information.
10.Remove all traces of sealant from threads of oil
filler/level plug.
11.Apply Loctite 290 to threads of oil filler/level plug
and tighten to25 Nm (18 lbf.ft).
12.Remove all traces of oil from main casing.
13.Fit underbelly panel.See CHASSIS AND
BODY, Repair.
ProCarManuals.com

MAINTENANCE
17
MAINTENANCE FRONT AND REAR AXLE OIL
Renew
A- Front and rear axle, 90 models, front, 110/130
models.
B- Rear axle, 110/130 models.
WARNING: Avoid excessive skin contact
with used axle oil. Used axle oil contains
potentially harmful contaminants which
may cause skin cancer or other serious skin
disorders.1.Ensure vehicle is level and place suitable tray
under axle to be drained.
2.Using 13mm square drive wrench, remove drain
and filler/level plugs from axle and allow oil to
drain completely.
3.Clean and refit drain plug.
4.Inject new oil, until it runs out from filler/level
hole. Allow excess oil to drain and wipe clean.
See LUBRICANTS, FLUIDS AND
CAPACITIES, Information.
5.Clean and refit filler/level plug.
Check
1.Ensure vehicle is level.
2.Using 13 mm square drive wrench, remove
filler/level plug.
3.If necessary inject new oiluntil oil runs out from
filler/level hole. Allow excess oil to drain and
wipe clean.See LUBRICANTS, FLUIDS AND
CAPACITIES, Information.
4.Clean and refit filler/level plug.
ProCarManuals.com

MAINTENANCE
23
MAINTENANCE ENGINE AND TRANSMISSION MOUNTINGS
1.Check condition of front LH engine mounting.
Tighten fixings if necessary.See ENGINE ,
Repair.
2.Check condition of front RH engine mounting.
Tighten fixings if necessary.See ENGINE ,
Repair.
3.Check condition of rear LH gearbox mounting.
Tighten fixings if necessary.See ENGINE ,
Repair.
4.Check condition of rear RH gearbox mounting.
Tighten fixings if necessary.See ENGINE ,
Repair.ROAD TEST
There are two purposes for conducting a road test.
Firstly, to ensure the work completed within the
dealership meets the standards required as layed
down by dealership processes. Secondly, for a skilled
technician to assess the general condition of the
vehicle and report any conditions that the customer
should be made aware of.
CAUTION: Two wheel roller tests must not
be carried out. Four wheel roller tests
must be restricted to 3 mph (5 kph).
1.Check for correct operation of starter switch.
Ensure the engine starts in a correct manner.
Leave the engine running.
2.With vehicle stationary, turn steering from lock to
lock. Check for smooth operation and ensure
there is no undue noise from the power steering
pump or drive belt.
3.Depress clutch and select all gears in turn.
Check for smooth notch free engagement.
4.Drive vehicle on a short road test. Check all
vehicle systems for correct operation. Pay
particular attention to:
Engine noise
Gearbox noise
Suspension noise
Body noise
Braking system operation
Gear selection
Engine performance
5.Check for correct operation of all instruments
and warning devices where practical.
6.After road test, carry out a final inspection of the
vehicle on vehicle ramps.
7.Check all underbonnet fluid levels and top-up if
necessary.
ProCarManuals.com

ENGINE
21
DESCRIPTION AND OPERATION Oil pressure switch
The oil pressure switch is located in a port on the outlet side of the oil cooler housing. It detects when a safe
operating pressure has been reached during engine starting and initiates the illumination of a warning light in the
instrument pack if the pressure drops below a given value.
ProCarManuals.com

ENGINE
35
DESCRIPTION AND OPERATION 1.To cylinder block main gallery (from rear of oil cooler housing)
2.Oil cooler housing
3.Oil pressure switch
4.Full-flow filter
5.Centrifuge filter
6.Return to sump
7.Flow from oil pump (via cylinder block)
8.Oil cooler matrix
When the engine temperature is below 74°C, the thermostat in the full-flow filter adaptor housing is closed and a
proportion of the oil flow to the main oil gallery is diverted to the oil cooler to supply an oil feed to the turbocharger
bearings. Oil passes through the oil cooler to the front gallery in the oil cooler housing where there is a tapping to
connect the feed pipe to the turbocharger. Oil used by the turbocharger bearings is returned to the sump through
an oil drain pipe which connects to a port in the LH side of the cylinder block.
The remainder of the oil flow leaving the full-flow filter outlet is passed into the cylinder block via a port at the rear
of oil cooler rear gallery.
When the oil temperature rises above 74°C the thermostat in the full-flow filter housing begins to open to allow a
proportion of the oil from the full-flow filter to pass through the oil cooler before it reaches the main oil gallery in the
cylinder block. In this instance, oil supply to the turbocharger bearings is fed directly from the full-flow filter without
first passing through the oil cooler. Between 74°C and 88°C the thermostat valve plunger opens by about 9 mm
(0.3 in) to allow proportionally more oil to flow through the oil cooler before being passed to the cylinder block main
oil delivery gallery. Above 88°C the thermostat valve continues to open by about 1mm (0.03 in) for every 10°C
increase in temperature until the valve is fully open, when all the oil flow to the cylinder block is forced to pass to
the cylinder block via the oil cooler.
An oil pressure switch is located in a port in the rear gallery of the oil cooler housing to sense the oil pressure level
before flow enters the main oil gallery in the engine block. A warning lamp in the instrument cluster is switched on
if the oil pressure is detected as being too low.
Drillings from the cylinder block main oil gallery direct oil to the crankshaft main bearings and cross drillings in the
crankshaft direct oil to the big-end bearings. An additional five drillings in the cylinder block supply oil at reduced
pressure to the oil squirt jets for piston cooling and gudgeon pin lubrication.
Oil supply from the cylinder block is then passed to the cylinder head galleries through a non-return valve which is
included as an integral item in the lower face of the cylinder head.
ProCarManuals.com