brake LAND ROVER DEFENDER 1999 Owner's Manual

MAINTENANCE
7
MAINTENANCE BRAKE PADS, CALIPERS AND DISCS
1.With front road wheels removed, check brake
pad thickness and ensure that both pads are
wearing evenly.
2.Check brake discs for signs of cracking,
excessive scoring or oil contamination.
NOTE: Any requirement to replace brake
pads or brake disc should be advised to
the customer as this will incur additional
labour and/or material cost and should not be
carried out without the authorisation of the
customer.
3.Check for any signs of brake fluid leakage from
caliper seals, hoses or unions.
4.Using brake cleaner, remove excessive deposits
of brake dust from pads, calipers and disc
shields.ROAD WHEEL SPEED SENSOR HARNESS - Td5
1.Check each sensor harness is correctly and
securely routed.
2.Inspect each harness for chafing or damage.
NOTE: Any requirement to replace a road
wheel speed sensor should be advised to
the customer as this will incur additional
labour and/or material cost and should not be
carried out without the authorisation of the
customer.
ProCarManuals.com

MAINTENANCE
11
MAINTENANCE BRAKE FLUID
1.Renew brake fluid.See BRAKES,
Adjustment.AIR FILTER ELEMENT AND DUMP VALVE
1.Replace air cleaner element.See FUEL
SYSTEM, Repair.
2.Remove all dirt from dump valve.
ProCarManuals.com

10MAINTENANCE
24
MAINTENANCE ENDORSE SERVICE RECORD
1.Insert date and mileage of next service.
2.Insert current mileage.
3.Tick one of the boxes on the brake fluid
replacement indicator.
4.Endorse service record with dealer stamp.
5.Sign and date the service record.
6.Sign and date the maintenance check sheet.REPORT ANY UNUSUAL FEATURES
1.Produce a written report detailing additional work
necessary, or items which may require attention
prior to the next service.
ProCarManuals.com

EMISSION CONTROL
3
DESCRIPTION AND OPERATION 1.EGR Solenoid
2.Vacuum hose (light brown)
3.T-piece
4.Vacuum hose to brake servo
5.Non-return valve
6.Brake servo
7.Inlet manifold
8.Exhaust manifold
9.EGR pipe
10.Vacuum pump/alternator assembly
11.Air intake hose from intercooler
12.EGR valve assembly
13.Vacuum hose to vacuum pump
14.Vacuum hose to EGR valve suction port (blue)
15.To atmosphere
16.In-line filter
17.Vent hose - EGR solenoid to in-line filter (green)
ProCarManuals.com

EMISSION CONTROL
5
DESCRIPTION AND OPERATION
CAUTION: Inset A shows the Pre-EU3 condition for the EGR pipe. Inset B shows the Pre-EU3
condition filter and venting.
1.ILT valve modulator
2.ILT modulator vacuum hose (brown)
3.EGR valve modulator
4.EGR modulator vacuum hose (brown)
5.Vent hose - EGR modulator to in-line filter (green)
6.Vacuum hose to ILT valve suction port (blue)
7.Vacuum hose to EGR valve suction port (blue)
8.’T’-piece (4-way)
9.Vacuum hose to brake servo
10.Non-return valve
11.Brake servo
12.Inlet manifold
13.Exhaust manifold
14.ILT valve
15.EGR cooler - EU-3 models
16.Vacuum pump/alternator assembly
17.Air intake hose from intercooler
18.EGR valve (incorporating ILT valve) assembly
19.Vacuum hose to vacuum pump
20.Vent hose - ILT valve modulator to in-line filter (green)
21.3-way connector
22.Vent hose to air cleaner
23.ILT modulator harness connector (green)
24.EGR modulator harness connector (black)
25.To atmosphere - Pre-EU3 models
26.In-line filter - Pre-EU3 models
27.EGR pipe - Pre-EU3 models
ProCarManuals.com

EMISSION CONTROL
9
DESCRIPTION AND OPERATION EGR MODULATOR
1.Port to vacuum source (white band)
2.Port to EGR valve (blue band)3.Port to atmosphere via in-line filter (green band)
4.Harness connector
The EGR modulator is located on a plate fixed to the inner RH front wing. The modulator is attached to the plate
by two studs, each with two nuts which secure the assembly to a rubber mounting, which helps reduce noise. The
modulator must be mounted vertically with the two vacuum ports uppermost.
Modulator operation is controlled by a signal from the ECM which determines the required amount of EGR needed
in response to inputs relating to air flow, engine operation, and ambient conditions. The modulator has a two pin
connector at its base to connect it to the ECM via the engine harness.
The modulator features three ports:
The top port is identified by a white band and connects to a T-piece in the vacuum line via a small bore light
brown plastic hose. The two other ports on the T-piece connect to the vacuum line hoses of black vinyl tubing
between the vacuum pump and the brake servo assembly attached to the bulkhead. The vacuum pump end of
the tubing terminates in a rubber elbow, which gives a vacuum tight seal on the suction port of the vacuum
pump. The brake servo end of the tubing terminates with a non-return valve in a plastic housing which plugs
into the front face of the brake servo housing.
The middle port is identified by a blue band, and connects to the suction port on the EGR valve through a small
bore blue plastic hose.
The lower port is identified by a green band and connects to atmosphere through an in-line filter via a small
bore green plastic hose.
The blue and brown vacuum hoses are protected by corrugated plastic sheaths. The ends of the hoses are fitted
with rubber boots to ensure vacuum tight seals at the component ports.
ProCarManuals.com

17EMISSION CONTROL
10
DESCRIPTION AND OPERATION INLET THROTTLE (ILT) MODULATOR
1.Port to vacuum source (white band)
2.Port to ILT valve (blue band)
3.Port to atmosphere via in-line filter (green band)
4.Harness connector (green)
The ILT modulator is located on a plate fixed to the inner wing on the RH side of the engine below the EGR
modulator. The modulator is attached to the plate by two through-studs, each with two nuts which secure the
modulator assembly to a rubber mounting which helps to reduce noise. The modulator must be mounted in the
vertical orientation with the two vacuum ports uppermost.
The modulator operation is controlled by a signal from the ECM which determines the required ratio of exhaust
gas to fresh inlet air needed in response to inputs relating to air flow and engine operating and ambient conditions.
The modulator has a green two-pin connector at its base to connect it to the ECM through the engine harness.
The ILT valve modulator features three ports:
The top port is identified by a white band and connects to a’T’-piece in the vacuum line via a small-bore brown
plastic hose where it is connected in parallel with the vacuum source line to the EGR valve modulator. The two
other ports on the’T’-piece connect vacuum line hoses of black vinyl tubing between the vacuum pump
attached to the alternator and the brake-servo assembly attached to the bulkhead.
The middle port is identified by a blue band and connects to the suction port on the ILT valve through a
small-bore blue plastic hose.
The lower port is identified by a green band and connects to atmosphere through an in-line filter via a green
plastic hose and a three-way connector positioned in-line between the modulators and the filter. The ILT
modulator hose is connected opposite to the two parallel ports at the three-way connector which connect the
vent lines to the EGR valve modulator and the in-line filter. The other port of the in-line filter vents directly to
atmosphere.
The blue and brown vacuum hoses are protected by corrugated plastic sheaths. The ends of the hoses are fitted
with rubber boots to ensure vacuum tight seals at the component ports.
ProCarManuals.com

18 - ENGINE MANAGEMENT SYSTEM
CONTENTS
Page
DESCRIPTION AND OPERATION
COMPONENT LOCATION 2...................................................................................
DESCRIPTION 5.....................................................................................................
ENGINE CONTROL MODULE (ECM) 6.................................................................
SENSOR - MASS AIR FLOW (MAF) 7....................................................................
SENSOR - AMBIENT AIR PRESSURE AND 8.......................................................
SENSOR - MANIFOLD ABSOLUTE PRESSURE 9................................................
SENSOR - ENGINE COOLANT TEMPERATURE 11.............................................
SENSOR - CRANKSHAFT SPEED AND 12...........................................................
SENSOR - THROTTLE POSITION (TP) 14............................................................
SENSOR - THROTTLE POSITION (TP) 15............................................................
ELECTRONIC UNIT INJECTOR (EUI) 18...............................................................
SENSOR - FUEL TEMPERATURE (FT) 20............................................................
RELAY - FUEL PUMP 21........................................................................................
RELAY - MAIN 21...................................................................................................
SWITCH - BRAKE PEDAL 22.................................................................................
SWITCH - CLUTCH PEDAL 22...............................................................................
MODULATOR - EXHAUST GAS REGULATOR (EGR) 23.....................................
WARNING LAMP - GLOW PLUG 23......................................................................
GLOW PLUGS 24...................................................................................................
TURBOCHARGER 26.............................................................................................
INTERCOOLER 27.................................................................................................
OPERATION 28......................................................................................................
REPAIR
ENGINE CONTROL MODULE (ECM) 1.................................................................
SENSOR - ENGINE COOLANT TEMPERATURE (ECT) 1....................................
SENSOR - CRANKSHAFT SPEED AND POSITION (CKP) 2................................
ProCarManuals.com

18ENGINE MANAGEMENT SYSTEM
4
DESCRIPTION AND OPERATION Passenger Compartment
1.Brake pedal switch.
2.Clutch pedal switch.
3.Accelerator pedal switch.
4.Diagnostic connector.
ProCarManuals.com

ENGINE MANAGEMENT SYSTEM
5
DESCRIPTION AND OPERATION DESCRIPTION
General
An engine control module (ECM) controls the five cylinder direct injection diesel engine, and works on the drive by
wire principal. This means there is no throttle cable, the ECM controls the drivers needs via a signal from the
Throttle Position (TP) sensor on the throttle pedal.
The ECM is a full authoritative diesel specific microprocessor that also incorporates features for air conditioning. In
addition, the ECM supplies output control for the Exhaust Gas Recirculation (EGR) and turbocharger boost
pressure. The ECM has a self diagnostic function, which is able to provide backup strategies for most sensor
failures.
The ECM processes information from the following input sources:
Mass Air Flow (MAF) sensor.
Ambient Air Pressure (AAP) sensor.
Manifold Absolute Pressure (MAP) / Inlet Air Temperature (IAT) sensor.
Engine Coolant Temperature (ECT) sensor.
Crankshaft Speed and Position (CKP) sensor.
Throttle Position (TP) sensor.
Fuel Temperature (FT) sensor.
Air conditioning request.
Air conditioning fan request.
Brake pedal switch.
Clutch pedal switch.
The input from the sensors constantly updates the ECM with the current operating condition of the engine. Once
the ECM has compared current information with stored information within its memory, it can make any adjustment
it requires to the operation of the engine via the following:
Air conditioning clutch relay.
Air conditioning cooling fan relay.
Electronic vacuum regulator solenoid.
Fuel pump relay.
Glow plug warning lamp.
Glow plugs.
Fuel injectors.
Main relay.
Turbocharger wastegate modulator.
Temperature gauge.
The ECM interfaces with the following:
Serial communication link.
Instrument pack.
ProCarManuals.com