differential LAND ROVER DEFENDER 1999 Owner's Manual

51REAR AXLE AND FINAL DRIVE
2
REPAIR Refit
15.Position axle and fit lower links. Tighten fixings
to176 Nm (130 lbf/ft).
16.If applicable, fit anti-roll bar links to axleSee
REAR SUSPENSION, Repair. Anti-roll bar
links.
17.Raise axle and locate road springs.
18.Fit coil spring retaining plates and secure with
fixing bolts.
19.Secure pivot bracket ball joint to axle bracket.
Tighten fixing to176 Nm (130 lbf/ft).
20.Align propeller shaft to differential drive flange
and tighten fixings to47 Nm (35 lbf/ft).
21.Reconnect flexible brake hose and axle breather
hose.
22.Refit shock absorbers.
23.Fit road wheels and tighten to correct torque:
Alloy wheels -130 Nm (96 lbf/ft)
Steel wheels -100 Nm (80 lbf/ft)
Heavy Duty wheels -170 Nm (125 lbf/ft)
24.Remove rear chassis support.
25.Bleed brake systemSee BRAKES, Repair.
brake system bleed.
ProCarManuals.com

REAR AXLE AND FINAL DRIVE
5
REPAIR DIFFERENTIAL ASSEMBLY - 90
Service repair no - 51.15.01
Remove
1.Using suitable container, drain axle oil.
2.Mark differential and propeller shaft flanges to
facilitate reassembly.
3.Remove 4 bolts and disconnect propeller shaft
from differential. Tie aside.
4.Remove 5 hub drive member bolts and withdraw
axle half shafts sufficiently to disengage from
differential unit.
5.Remove 10 nuts securing differential to axle
case.
6.Withdraw differential unit.
NOTE: The differential unit can only be
serviced as a complete assembly with
matching drive pinion. For advice ring
Land Rover Service Department.Refit
7.Ensure mating faces are clean and apply a bead
of RTV sealant to axle case.
8.Support differential unit and position on axle
casing.
9.Secure with self locking nuts and tighten to40
Nm (30lbf/ft).
10.Align marks on flanges and secure propeller
shaft to differential. Tighten bolts to48 Nm (35
lbf/ft).
11.Refit half shafts, using new drive member
gaskets. Tighten bolts to65 Nm (48 lbf/ft).
12.Refill axle oil with approved lubricantSee
LUBRICANTS, FLUIDS AND CAPACITIES,
Information. Recommended lubricants and
fluids.
ProCarManuals.com

REAR AXLE AND FINAL DRIVE
1
OVERHAUL DIFFERENTIAL ASSEMBLY - 110/130
Service repair no - 51.15.07
Overhaul
1.Drain off differential lubricating oil, and refit plug.
2.Remove rear axle assembly from vehicleSee
Repair. Rear axle
3.Remove hub driving member fixings.
4.Withdraw driving member and axle shaft
sufficiently to disengage differential.
5.Repeat instruction 4 for other axle shaft.
6.Remove fixings and support strip at differential
cover and withdraw cover and joint washer.
7.Note relationship marking on bearing caps and
axle casing to ensure correct refitting.
8.Remove fixings and withdraw differential bearing
caps.
9.Clean out and examine spreader tool peg holes
provided in gear casing face; ensure that holes
are free from dirt and burrs and damage.
10.Ensure that turnbuckle adjuster is free to turn.
Using axle compressor LRT-51-503
11.Place tool on to differential casing, as illustrated,
with weld seam uppermost. Ensure that plates
rest squarely on differential machined surface
and end bars butt against edges of casing.
12.Tighten adjusting nuts by hand only, until all
slack is taken up.
13.Continue to tighten both nuts alternately with a
spanner, one flat at a time, to a maximum of
three flats.
14.Carefully lever-out differential assembly.
ProCarManuals.com

51REAR AXLE AND FINAL DRIVE
2
OVERHAUL
CAUTION: To prevent permanent damage
to the gear carrier case, it must not be
over-stretched. Each flat on the turnbuckle
is numbered to enable a check to be made on the
amount turned. The maximum stretch permitted is
0,30 mm, equivalent to three flats.
15.Ease off adjuster and remove spreader.
Using axle compressor LRT-51-503
16.Place tool on to differential casing, as illustrated,
with weld seam uppermost. Ensure that plates
rest squarely on differential machined surface
and end bars butt against edges of casing.
17.Tighten adjusting nuts by hand only, until all
slack is taken up.
18.Continue to tighten both nuts alternately with a
spanner, one flat at a time, to a maximum of
three flats.
19.Carefully lever-out differential assembly.
Dismantle differential
20.Add alignment marks between crown wheel and
differential case for reassembly purposes, then
remove fixings and withdraw crown wheel.
21.Note alignment markings on two differential
casings to ensure correct refitting, then remove
fixings.
22.Lift off upper case.
23.Withdraw upper differential wheel and thrust
washer.
24.Lift out cross-shaft and pinions.
ProCarManuals.com

REAR AXLE AND FINAL DRIVE
3
OVERHAUL
25.Withdraw four dished thrust washers.
26.Withdraw lower differential wheel and thrust
washer.
27.Remove differential bearing cones using
LRT-51-500, adaptors 1 and 2 and press
LRT-99-002.
28.Withdraw shim washers fitted between bearing
cones and differential casings.
Remove final drive pinion
29.UsingLTR-51-003to prevent coupling flange
from rotating, remove flange locknut and plain
washer.
30.Support drive pinion and remove coupling flange
by tapping with a hide hammer.
31.Withdraw drive pinion together with inner bearing
cone.
32.Withdraw and discard collapsable bearing
spacer.
33.Withdraw oil seal, gasket and oil thrower.
34.Withdraw outer bearing cone.
35.UsingLRT-51-502, extract pinion inner bearing
cup and shim washers from casing. Note shim
washer thickness.
36.Extract pinion outer bearing cup from casing
usingLRT-51-502.
ProCarManuals.com

51REAR AXLE AND FINAL DRIVE
4
OVERHAUL
37.UsingLRT-51-500and pressLRT-99-002,
remove inner bearing cone from pinion.
INSPECTION
38.Examine all components for obvious wear or
damage.
39.Bearing cones must be a press fit on their
locations, except drive pinion flange and bearing
which is a slide fit.
40.The crown wheel and pinion are supplied as a
matched pair and must not be interchanged
separately. A new crown wheel and pinion
matched pair may be fitted to an original gear
carrier casing if sound. original crown wheel and
pinion, if sound, may be fitted into a replacement
casing.
41.The two parts of differential unit casing are
matched and must not be replaced separately.
42.Discard and renew all thrust washers.
43.Differential housings with worn thrust washer
seatings must be replaced as a pair.
44.Examine differential case to crown wheel joint
face for burrs and damage which could lead to
crown wheel run-out when fitted.ASSEMBLE
Differential
45.Fit differential lower wheel and thrust washer to
differential case. See illustration following
instruction 23.
46.Fit dished thrust washers.
47.Fit cross-shaft and pinions.
48.Fit differential upper wheel and thrust washer.
49.Fit differential upper case lining-up marks.
50.Secure assembly with bolts using Loctite
’Studlock’grade CVX on threads and tighten
evenly and diametrically to95 Nm (70 lbf/ft).
51.Fit crown wheel to differential casing. Use Loctite
’Studlock’grade CVX on fixing bolt threads and
tighten to correct torque.
52.Press on differential roller bearing cones less
shim washers, usingLRT-51-504, and leave to
one side until required for instruction 96.
53.Fit bearing cups to differential.
54.Fit differential unit and bearings to gear carrier
casing, and rotate unit to centralize bearings. Do
not fit bearing caps.
ProCarManuals.com

REAR AXLE AND FINAL DRIVE
5
OVERHAUL
55.Position a suitable dial gauge indicator on casing
with stylus registering on back face of crown
wheel.
56.Rotate differential and check total indicated
run-out on crown wheel back face. This must not
exceed 0,05 mm. If run-out is excessive, check
mating faces for dirt and damage; if necessary,
select a new radial position for crown wheel.
When satisfactory, continue with following check.
Differential bearing adjustment
57.Insert two levers between casing and differential
unit at one side.
58.Move differential unit fully to one side of casing;
do not tilt unit.
59.Rotate differential unit to settle bearings,
continue to lever differential to side, then zero
dial gauge indicator.
60.Lever assembly fully to other side of casing,
rotate unit to settle bearings, then note total
indicator reading.
61.Add 0,127 mm, for bearing pre-load, to total
noted in preceding instruction. The sum is then
equal to nominal value of shims required for
differential bearings. Shims are available in
range 0,07 mm, 0,12 mm, 0,25 mm and 0,76
mm. Select total value of shims required.
62.Remove differential unit and bearings and place
aside. Do not fit shim washers until subsequent
’Differential backlash’checks have been made,
instructions 96 to 102.Fit drive pinion
63.Select shim washers of same thickness value as
those removed from under pinion inner cup,
instruction 35, and place ready for fitting.
64.Position outer bearing replacerLRT-51-505,
detail 2, and outer bearing cup on press
LRT-99-502.
65.Locate assembly into pinion housing nose.
66.Place selected shim washers on to inner bearing
cup seating.
67.Position inner bearing cup in casing.
68.Position inner bearing replacerLRT-51-505,
detail 1, ontoLRT-99-502and secure with fixing
nut.
69.Hold still centre screw and turn butterfly lever to
draw in bearing cups.
Note: If above tools are not available, a suitable piece
of tubing, positioned on bearing inner race and a hand
press may be used.
ProCarManuals.com

51REAR AXLE AND FINAL DRIVE
6
OVERHAUL
70.Support inner bearing on bed of hand press and
press drive pinion into bearing.
71.Position pinion and bearing in casing; omit
collapsable spacer at this stage.
72.Fit outer bearing cone onto pinion.
73.Fit coupling flange and plain washer and loosely
fit flange nut.
74.Tighten coupling flange locknut to remove
end-float from pinion.
75.Rotate pinion to settle bearings and slowly
tighten flange locknut. Use a spring balance to
obtain a torque resistance of 11 Kgf/cm (18
lbf/in) to rotate pinion.
Drive pinion markings
76.Check that serial number marked on pinion end
face matches that marked on crown wheel.
77.The markings on end face adjacent to serial
number are of no significance during servicing.
78.The figure marked on end face opposite to serial
number indicates, in thousandths of an inch,
deviation from nominal required to correctly set
pinion. A pinion marked plus (+) must be set
below nominal, a minus (-) pinion must be set
above nominal. An unmarked pinion must be set
at nominal.
79.The nominal setting dimension is represented by
setting gauge blockLRT-54-503, which is
referenced from pinion end face to bottom radius
of differential bearing bore.
Drive pinion adjustment
80.Ensure that pinion end face is free of raised
burrs around etched markings.
81.Remove keep disc from magnetized base of dial
gauge toolLRT-99-006.
82.Place dial gauge and setting gaugeLRT-54-503
on a flat surface and zero dial gauge stylus on to
setting gauge.
ProCarManuals.com

REAR AXLE AND FINAL DRIVE
7
OVERHAUL
83.Position dial gauge centrally on pinion end face
with stylus registering on lowest point on one
differential bearing bore. Note dial gauge
deviation from zeroed setting.
84.Repeat on other bearing bore. Add together
readings, then halve sum to obtain mean
reading. Note whether stylus has moved up or
down from zeroed setting.
Example 1
Reading obtained LH side.............. + 0.1524mm
Reading obtained RH side............. - 0.0762mm
Add + 0.1524mm - 0.0762mm = + 0.0762mm
Divide by 2 (0.0762 divided by 2)= 0.0381mm
Therefore subtract 0.0381mm from shim thickness
behind pinion inner bearing track.
Example 2
Reading obtained LH side............. + 0.1524mm
Reading obtained RH side............ - 0.2032mm
Add + 0.1524mm - 0.2032mm = + 0.0508mm
Divide by 2 (0.0508 divided by 2)= 0.0254mm
Therefore add 0.0254mm from shim thickness behind
pinion inner bearing track.
Pinion height setting block LRT-54-503
85.Where stylus has moved down (85a), amount is
equivalent to thickness of shims that must be
removed from under pinion inner cup to bring
pinion down to nominal position. Where stylus
has moved up (85b), amount is equivalent to
additional thickness of shims required to bring
pinion up to nominal position.
Ensure that height marked 30.93 mm is used for this
differential.
ProCarManuals.com

REAR AXLE AND FINAL DRIVE
9
OVERHAUL Differential backlash checks
96.Pick up differential unit as left after instruction
52.
97.Fit differential unit and lever unit away from drive
pinion until opposite bearing cup is seated
against housing. Do not tilt unit.
98.Install a dial gauge on casing with its stylus
resting on back face of crown wheel. Zero the
gauge.
99.Lever differential unit to engage crown wheel
teeth in full mesh with drive pinion teeth. Do not
tilt unit.
100.Note total reading obtained on dial gauge.
101.From this figure subtract 0,25 mm to obtain
correct crown wheel backlash when fitted. The
result indicates value of shimming to be fitted
between differential case and bearing cone at
crown wheel side of differential.
102.Fit shim value determined in instruction 101,
taking shims from pack previously determined
during’Differential bearing adjustment’checks,
instructions 57 to 62LRT-51-500details 1 and 2,
pressLRT-99-002, andLRT-51-504.
103.Fit remaining shims from instruction 101 to
opposite side of differential.LRT-51-501details
1 and 2, pressLRT-99-002, andLRT-51-504.
104.Fit differential unit with shims and bearings to
axle casing, using axle compressorLRT-51-503
.
105.Remove axle compressor106.Fit bearing caps in their correct position,
referring to relationship markings on caps and on
axle casing.
107.Tighten bearing caps fixings to135 Nm (100
lbf/ft).
108.Mount a dial gauge on axle casing with stylus
resting on a crown wheel tooth.
109.Prevent drive pinion from rotating and check
crown wheel backlash which must be 0,15 to
0,27 mm. If backlash is not within specified
limits, repeat differential backlash checks,
instructions 96 to 102 looking for possible errors.
110.Fit differential cover and new gasket, coating
both sides of gasket with Hylomar PL 32M or an
equivalent non-setting sealant. Torque load for
fixings is30 Nm (22 lbf/ft).
111.Reverse instructions 3 to 5 and coat threads of
hub driving member bolts with Loctite’Studlock’
grade CVX and fit and tighten bolts evenly to
correct torque.
112.Fit rear axle assembly to vehicleSee Repair.
Rear axle.
113.Replenish differential with recommended
lubricantSee LUBRICANTS, FLUIDS AND
CAPACITIES, Information. Recommended
lubricants and fluids. After initial axle run,
check oil level and replenish as necessary to
filler/level plug hole.
114.Where major running parts have been replaced
during servicing, it is a recommended practice to
allow axle assembly to’run in’by avoiding,
where possible, heavy loads and high speeds
during initial running.
ProCarManuals.com