lock LAND ROVER DEFENDER 1999 Repair Manual

ENGINE
25
REPAIR
6.Using sequence shown, remove and discard 22
bolts securing oil pump and stiffener assembly.
7.Remove oil pump and stiffener assembly.
NOTE: Dowel located.
8.Remove and discard’O’ring.Refit
9.Clean mating faces of oil pump and stiffener
assembly to main bearing caps and cylinder
block.
10.Fit new’O’ring to oil pump housing.
11.Position oil pump and stiffener assembly on to
cylinder block ensuring 2 dowels are correctly
located.
12.Fit new bolts and using sequence shown, tighten
to13 Nm (10 lbf.ft).
13.Lubricate a new’O’ring with engine oil and fit to
oil pick-up strainer.
14.Fit oil pick-up strainer, apply Loctite 242 to
threads of Torx screws; fit screws and tighten to
10 Nm (7 lbf.ft).
ProCarManuals.com

12ENGINE
26
REPAIR
15.Position oil pump drive sprocket and chain on to
oil pump ensuring that the’D’shape on the drive
sprocket is located on flat on the oil pump drive
shaft.
16.Clean oil pump drive sprocket retaining bolt and
apply Loctite 242 to bolt threads.
17.Fit oil pump drive sprocket retaining bolt and
tighten to25 Nm (18 lbf.ft).
18.Fit new sump gasket.See this Section.GASKET - ENGINE TO SUMP
Service repair no - 12.60.38
Remove
1.Remove battery cover.
2.Disconnect battery negative lead.
3.Remove exhaust front pipe.See MANIFOLD
AND EXHAUST SYSTEM, Repair.
4.Drain engine oil.
5.Loosen 4 bolts securing sump to gearbox bell
housing.
6.Remove 2 bolts securing centrifuge drain pipe to
sump and discard gasket.
7.Using sequence shown and noting their fitted
position, remove 20 bolts securing sump.
8.Remove sump, remove and discard gasket.
CAUTION: Do not lever between sump and
cylinder block.
ProCarManuals.com

12ENGINE
2
OVERHAUL GASKET - EXHAUST MANIFOLD
Service repair no - 30.15.12.01
Remove
NOTE: The following procedure covers
both EU3 and non EU3 engines
NOTE: EU3 engine illustrated.
1.Remove 3 bolts securing heater pipe to cylinder
head and turbocharger heat shield.
2.Remove heater pipe.
3.Remove bolt and remove turbocharger heat
shield.
4.Remove and discard 2 Allen screws securing
EGR pipe to exhaust manifold.
5.Remove banjo bolt securing oil feed pipe to
turbocharger and discard sealing washers.
6.Loosen turbocharger drain hose union at
cylinder block.
7.Remove 10 nuts and remove exhaust manifold
and turbocharger.
8.Remove manifold gasket.Refit
1.Clean exhaust manifold mating faces.
2.Position exhaust manifold to cylinder head using
new gasket and fit manifold nuts.
3.Working from the centre outwards, fit and tighten
nuts to25 Nm (18 lbf.ft).
4.Clean turbocharger drain and feed hose unions.
5.Fit turbocharger oil drain hose to cylinder block
and tighten union to48 Nm (35 lbf.ft).
6.Fit new sealing washers to turbocharger oil feed
pipe, fit banjo bolt and tighten to25 Nm (18
lbf.ft).
7.Position EGR pipe to exhaust manifold. Fit new
Allen screws and tighten to10 Nm (7 lbf.ft).
8.Position turbocharger heat shield.
9.Position heater pipe to cylinder head and tighten
bolts to25 Nm (18 lbf.ft).
10.Position exhaust manifold heatshield and tighten
M6 bolts to9 Nm (7 lbf.ft)and M8 bolt to25
Nm (18 lbf.ft).
ProCarManuals.com

12ENGINE
4
OVERHAUL
11.Disconnect alternator/vacuum pump oil feed pipe
union from cylinder head, remove and discard
’O’ring.
12.Remove camshaft sprocket access plug from
front of cylinder head, remove and discard’O’
ring.
13.Remove timing chain fixed guide Allen screw.
14.Remove timing chain tensioner, remove and
discard sealing washer.
15.Remove and discard 3 bolts securing camshaft
sprocket to camshaft; release sprocket from
camshaft.
16.Remove bolt and nut securing front of cylinder
head to timing chain cover.
17.Using sequence shown, progressively loosen
then remove 12 cylinder head bolts; discard
bolts together with their captive washers.
18.Using assistance, remove cylinder head and
place on 2 wooden blocks.
CAUTION: Cylinder head is dowel located,
do not tap it sideways to free it from
cylinder block. Support both ends of
cylinder head on blocks of wood. With the
camshaft carrier bolted down, the injector nozzles
and some of the valves will protrude from the face
of the cylinder head.
19.Remove the cylinder head gasket.
20.Note the gasket thickness indicator and ensure
the same thickness gasket is used on refitment
of the cylinder head.
CAUTION: If new pistons, connecting rods
or crankshaft are fitted, it will be
necessary to measure piston stand proud
in order to determine thickness of gasket
required.See this Section.
21.Remove and discard 2 plastic locating dowels
from cylinder block.
22.Carry out cylinder head overhaul procedures.
See this Section.
ProCarManuals.com

ENGINE
5
OVERHAUL Refit
1.Thoroughly clean cylinder block and cylinder
head mating faces.
2.Ensure coolant and oil passageways are clear
and bolt holes are clean and dry.
3.Ensure locating dowel holes in cylinder block are
clean and dry.
4.Fit new plastic locating dowels in cylinder block.
5.Fit new cylinder head gasket of the correct
thickness with the word’TOP’uppermost.
CAUTION: Gasket must be fitted dry.
6.Ensure that camshaft timing pinLRT-12-158is
still in position and using assistance, fit cylinder
head.
7.Carefully enter new cylinder head bolts together
with their captive washers,DO NOT DROP.
Lightly tighten bolts.
CAUTION: Cylinder head bolts are
pre-lubricated and do not require
additional lubrication.
8.Using sequence shown, tighten cylinder head
bolts to:
Stage 1 -30 Nm (23 lbf.ft)
Stage 2 -65 Nm (48 lbf.ft)
Stage 3 -90
°
Stage 4 -Further 180°
Stage 5 -Further 45°
CAUTION: Ensure correct tightening
sequence is followed for all 5 tightening
stages. Do not tighten bolts 315°in one
operation.9.Fit cylinder head to timing chain cover nut and
bolt and tighten to25 Nm (18 lbf.ft).
10.Clean camshaft sprocket and mating face on
camshaft.
11.Ensure engine is set to TDC firing - No.1
cylinder.
12.Check that mark on camshaft sprocket is
positioned between the 2 coloured links on
timing chain.
13.Position sprocket to camshaft, fit and lightly
tighten 3 new bolts then loosen bolts half a turn.
ProCarManuals.com

12ENGINE
6
OVERHAUL 14.Clean fixed guide Allen screw and apply Loctite
242 to screw threads.
15.Fit fixed timing chain guide Allen screw and
tighten to25 Nm (18 lbf.ft).
16.Clean timing chain tensioner and fit new sealing
washer.
17.Fit timing chain tensioner and tighten to45 Nm
(33 lbf.ft).
18.Tighten camshaft sprocket bolts to36 Nm (27
lbf.ft).
19.Remove toolLRT-12-058from camshaft.
20.Lubricate a new’O’ring with engine oil and fit to
camshaft sprocket access plug.
21.Fit camshaft sprocket access plug.
22.Clean alternator/vacuum pump oil feed hose
union.
23.Lubricate a new’O’ring with engine oil and fit to
alternator/vacuum pump hose union.
24.Fit and tighten alternator/vacuum pump oil hose
union to10 Nm (7 lbf.ft).
25.Fit bolt securing alternator strap bracket to
cylinder head and tighten to25 Nm (18 lbf.ft).
26.Connect multiplugs to ECT sensor and EUIs.
CAUTION: Following cylinder head
overhaul, it will be necessary, before
fitting the camshaft cover, to adjust the
fuel injector rockers using the following
procedures:
27.Rotate engine clockwise until No. 1 EUI lobe is
at full lift.
28.Tighten No.1 rocker adjusting screw until the EUI
plunger is felt to’bottom out’.
29.Loosen rocker adjusting screw 1 complete turn
to give EUI plunger the required bump clearance
and tighten rocker adjusting screw locknut to16
Nm (12 lbf.ft).
CAUTION: Ensure screw does not turn as
locknut is tightened.30.Carry out above procedures for the remaining 4
rocker arms.
31.After completion of rocker adjustment, slowly
rotate engine clockwise 2 complete turns by
hand to ensure that no EUI’s are bottoming out
on their plungers.
32.Clean camshaft cover and mating face.
33.Fit new sealing washers and isolators as
necessary to camshaft cover.
34.Fit new camshaft cover gasket to cover.
CAUTION: Gasket must be fitted dry.
35.Fit camshaft cover to camshaft carrier, fit bolts
and working from the centre outwards, tighten
bolts to10 Nm (7 lbf.ft).
36.Fit inlet manifold gasket.See MANIFOLD AND
EXHAUST SYSTEM, Repair.
37.Fit exhaust manifold gasket.See MANIFOLD
AND EXHAUST SYSTEM, Repair.
38. EGR cooler fitted:-Position EGR pipe to cooler,
fit new Allen screws and tighten to10 Nm (7
lbf.ft).
ProCarManuals.com

ENGINE
7
OVERHAUL CYLINDER HEAD GASKET SELECTION
NOTE: There are three thicknesses of
cylinder head gasket available and in order
that the correct gasket is fitted, it will be
necessary to determine the stand proud
(protrusion) of each piston above the top face of
the cylinder block. Gaskets have either 1, 2 or 3
identification holes and the following procedures
must be followed in order that the correct gasket
is selected.
1.Temporarily fit and lightly tighten a new
crankshaft pulley bolt.
2.Assemble a magnetic base DTI to cylinder block
top face adjacent to No. 1 cylinder bore.
3.Position stylus to cylinder block top face and
zero gauge.
4.Using crankshaft pulley bolt, rotate crankshaft in
a clockwise direction until No.1 piston is at TDC -
Woodruff key slot in crankshaft is at 12 o’clock.5.Position stylus of DTI at edge of piston and
directly over gudgeon pin axis.
6.Measure and record No.1 piston protrusion.
CAUTION: Measurement must be taken at
front and rear of piston.
7.Establish average of the 2 readings taken.
8.Repeat above procedures for remaining pistons.
9.From readings obtained, determine HIGHEST
piston protrusion figure and select the
appropriate cylinder head gasket:
Piston protrusion = 0.351 to 0.50 mm (0.014 to
0.02 in) - Select the 2 hole gasket.
Piston protrusion = 0.501 to 0.57 mm (0.021 to
0.022 in) - Select the 1 hole gasket.
Piston protrusion = 0.571 to 0.65 mm (0.022 to
0.025 in) - Select the 3 hole gasket.
10.Remove DTI.
11.Fit cylinder head gasket.See this Section.
ProCarManuals.com

12ENGINE
8
OVERHAUL CYLINDER HEAD - OVERHAUL
Service repair no - 12.29.19.01
Dismantling
1.Remove cylinder head gasket.See this
Section.
CAUTION: Due to the design of the
cylinder head which incorporates drillings
for the fuel injection system, it is important
that absolute cleanliness is adhered to when
carrying out overhaul procedures.
2.Note the gasket thickness indicator and ensure
the same thickness gasket is used on refitment
of cylinder head.
CAUTION: If new pistons, connecting rods
or crankshaft are fitted, it will be
necessary to determine thickness of
gasket required.See this Section.
3.Remove 4 glow plugs.
4.Disconnect multiplugs from EUI’s and remove
harness from camshaft carrier. Remove and
discard’O’ring from harness multiplug.
5.Loosen lock nuts and fully unscrew rocker
adjusting screws; discard locknuts and screws.
6.Remove and discard 6 bolts securing rocker
shaft, remove shaft.
NOTE: Dowel located.
7.Using sequence shown, progressively loosen 13
bolts securing camshaft carrier to cylinder head
until valve spring pressure is released; remove
bolts.
CAUTION: Do not discard bolts at this
stage.
ProCarManuals.com

12ENGINE
10
OVERHAUL
20.Using toolLRT-12-071, remove and discard
valve stem oil seal.
21.Repeat above operations to remove remaining
valves.
22. Engine Serial No. Prefixes 15P to 19P:-
Disconnect spill return pipe from cylinder head
and fuel connector block, remove and discard’O’
rings.
ProCarManuals.com

ENGINE
11
OVERHAUL
23.Remove 3 bolts and remove fuel connector
block from cylinder head.
24.Remove and discard gasket,’O’ring and fuel
filter.
25.Remove spacer block and gasket (if fitted).Cylinder head and camshaft carrier - cleaning
1.Thoroughly clean cylinder head mating faces,
ensure oil and coolant passages are clear and
bolt holes are clean and dry.
CAUTION: Take care to ensure that EUI
drillings are clear.
2.Using suitable solvent, remove all traces of
sealant and gasket material.
CAUTION: Do not use metal scrapers.
3.Remove all traces of oil from camshaft bearings
and journals.
4.Clean glow plug threads.
Cylinder head - Inspection
1.Check core plugs for signs of leakage and
corrosion, seal replacement plugs with Loctite
243.
2.Check cylinder head for warping across centre
and from corner to corner.
Maximum cylinder head warp =0.1 mm (0.004
in).
CAUTION: Cylinder heads may not be
refaced, replace the head assembly if
warping exceeds the limit given.
ProCarManuals.com